• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.55-65
• /
• 1999

An experimenta investigation of unsteady impinging DI diesel spray on the unheated plate and heated plate has been conducted in a pressurized chamber using high speed shadowgraphy. The ambient agas pressure was varied using nitrogen with chamber pressure of 1.1MPa, 2.1MPa and 2.6MPa. As the increase of ambient gas pressure of ambient gas pressure, the height of spray is increased if entrainment and circulation . At higher temperature of impinging plate, the radial penetration of the impinging spary is incresed , but the height of impinging spray is decreased.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.937-939
• /
• 2014

Recently, an intelligent APT(Advanced Persistent Threat) attack which aims to a special target is getting to be greatly increased. It is very hard to protect with existing intrusion detection methods because of the difficulties to protect the initial intrusion of malicious code. In this paper, we analyze out-bound traffics to prevent call-back step after malicious code intrusion, and propose an APT malicious traffic detection method with considering of trust. The proposed method is expected to provide a basement to improve the detection rate in comparing with that of existing detection methods.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.1
• /
• pp.66-78
• /
• 2004

The objective of this study was to apply the vibration technique to reduce the viscosity of bonding adhesives and thereby compare the bond strength and resin penetration in enamel and dentin achieved with those gained using the conventional technique and vibration technique. For enamel specimens, thirty teeth were sectioned mesio-distally. Sectioned two parts were assigned to same adhesive system but different treatment(vibration vs. non-vibration). Each specimen was embedded in 1-inch inner diameter PVC pipe with a acrylic resin. The buccal and lingual surfaces were placed so that the tooth and the embedding medium were at the same level. The samples were subsequently polished silicon carbide abrasive papers. Each adhesive system was applied according to its manufacture's instruction. Vibration groups were additionally vibrated for 15 seconds before curing. For dentin specimen, except removing the coronal part and placing occlusal surface at the mold level, the remaining procedures were same as enamel specimen. Resin composite(Z250. 3M. U.S.A.) was condensed on to the prepared surface in two increments using a mold kit(Ultradent Inc., U.S.A.). Each increments was light cured for 40 seconds. After 24 hours in tap water at room temperature, the specimens were thermocycled for 1000cycles. Shear bond strengths were measured with a universal testing machine(Instron 4465, England). To investigate infiltration patterns of adhesive materials, the surface of specimens was examined with scanning electron microscope. The results were as follows: 1. In enamel the mean values of shear bond strengths in vibration groups(group 2, 4, 6) were greater than those of non-vibration group(group 1, 3, 5). The differences were statistically significant except AQ bond group. 2. In dentin, the mean values of shear bond strengths in vibration groups(group 2, 4, 6) were greater than those of non-vibration groups(group 1, 3, 5). But the differences were not statistically significant except One-Up Bond F group. 3. The vibration group showed more mineral loss in enamel and longer resin tag and greater number of lateral branches in dentin under SEM examination.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.6
• /
• pp.576-582
• /
• 2013

To obtain the basic information on wood preservative process using copper, the penetration ACQ-2 preservative agent into Douglas fir wood and its degradational characteristics were investigated. Douglas fir is known to be difficult for preservative agent injection. To find the hindrance factor of the preservatives movement, the ray height, ray density, and length of tracheid were measured and observed by a stereoscopic microscope and scanning electron microscope. The results were compared in the well-penetrated parts of preservatives and insufficient parts. There were no significant differences in height, length, and density between both parts, except for the pits of the wood elements observed in SEM micrograph. More declosed pits were found in the well-penetrated parts of preservatives. Decay characteristics of wood specimen treated with various ACQ concentrations by brown-rot fungi was observed by an optical microscope. The decayed properties of tracheid, rays, and resin canals was found in the non-treated wood specimens and it was also found that some extent of preservatives concentration is necessary to protect the decay.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.11
• /
• pp.19-26
• /
• 2010

An influence factors for soundness evaluation of river levee include consisting embankment in case piping, permeability coefficient of ground, height of embankment, the width of crest, material characteristics of embankment and foundation ground, shape of embankment slope, an influence for penetration of rainfall or river water in case slope stability. In this study, it was operated a feasibility investigation of existing design result, stability evaluation for permeability coefficient use and permeability coefficient change of foundation ground to investigate an influence in line with permeability coefficient change for result of river levee penetration analysis. The evaluation results of influence factors, the permeability coefficient was used in design and it was evaluated influence in safety factor of piping. After the evaluation of influence factors, the permeability coefficient used in the design appears with the fact that differs in a design report about same soil.

• Journal of the Society of Disaster Information
• /
• v.14 no.4
• /
• pp.421-429
• /
• 2018

Purpose: This study conducted a slope stability study considering changes in the ground water level due to rain phenomena and the duration of rainfall, that is for the purpose of analyzing the stability of the slope surface of the cut section, seepage numerical analysis is performed by height of slope and rainfall accident, and the characteristics of rainfall was applied reasonably in order to determine the slope change during rain by analyzing rainfall and rainfall pattern due to climate change. Results: As a result of numerical analysis of stability for slope composed of the granite weathered soils according to the characteristics of rainfall(Uniform Rainfall, US Army Corps., Huff's method - 1/4, 4/4), Conclusion: The higher the slope, the smaller the safety factor of the slope, the smaller the elevation of the ground water level as the rainwater seepage does not reach the underground water level. In addition, the ground water level was assessed to be rose significantly in condition of case 3 Huff's method - 1/4, rain pattern with the largest initial rainfall duration, and the safety factor was analyzed to be small.

• Applied Microscopy
• /
• v.25 no.3
• /
• pp.75-81
• /
• 1995

The microstructural characterization of ternary $ZnS_{x}Se_{1-x}$(x=0.085) on GaAs(001) substrate grown up to $2{\mu}m\;at\;300^{\circ}C$ by molecular beam epitaxy(MBE) which has a single growth chamber was investigated by high resolution transmission electron microscope (HRTEM) working at 300 kV with point resolution of 0.18nm. The interface in the ZnSSe/GaAs specimen maintains a pseudomorphism with the substrate, but the epilayer has high density of stacking faults and moire fringes. The pits which had formed along <111> direction were found at the interface of ZnSSe/GaAs. The pits were responsible for producing defects in both epilayer and substrate. The wavy interface which has the difference of 15nm in height was found to maintain the pseudomorphism with the substrate and no stacking faults were found around the interface. However there exists faint and fine moire fringes in the epilayer near interface.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.3
• /
• pp.175-181
• /
• 2003

In this reseach, a seepage test is carried out for three kinds of soil using a upward seepage equipment. Reliability about the existing method of pipining investigation were verified making an estimate of the critical velocity, the critical hydraulic gradient, and hydraulic conductivity and so on. Also, sensitive analyses were carried out using Plaxis that is FEM Program about design factors of scour. The height of core had a big infulence on the hydraulic gradient of the embankment's lower part in the result of sensitive anaylsis. Also, second only to the height of core, and the slope of embankment, the width of crest had influence on scour. However, the change of hydraulic gradient in the effluent gateway had a little influence on the crest width of core. Using these results of sensitive analysis on designing, hydraulic gradient in the effluence gateway turned out to be reducing by altering design factors that change of sensitiveness is big, in case of the hydraulic gradient bigger than the standard hydraulic gradient.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.287-292
• /
• 2005

The flowfields generated by gaseous slot injection into a supersonic flow at a Mach number of 3.75 and a Reynolds number of $2.07{\times}10^7$ are simulated numerically. Fine-scale turbulence effects are represented by a two-equation(k-w SST model) closure model which includes $y^+$ effects on the turbulence model. Grid convergence index(GCI) is also considered to provide a measure of uncertainty of the grid convergence. Comparison is made with experimental data and other turbulence model in term of surface static pressure distributions, the length of the upstream separation region, and the penetration height. Results indicate that the k-w SST model correctly predicts mean surface pressure distribution and upstream separation length. However, it is also observed that the numerical simulation over predicts the pressure spike and penetration height compared with experimental data. All these results are taken within $1\%$ error band of grid convergence.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.9
• /
• pp.863-878
• /
• 2009

Unsteady three-dimensional flowfield generated by transverse fuel injection into a supersonic mainstream is simulated with a DES turbulence model. Comparisons are made with experimental results in terms of the temporal eddy position and eddy formation frequency. The vorticity field around the jet exit is also analyzed to understand the formation mechanism of the large eddy structures. Results indicate that the DES model correctly predicts the convection characteristics of the large scale eddies. However, it is also observed that the numerical results slightly over-predict the eddy formation frequency. The large eddy structures are generated as the counter-rotating vortices are detached alternately in the upstream recirculation region.