• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.467-471
• /
• 2011

PET bottle is manufactured by blow molding the preform, which is molded by injection molding. The neck part of the preform of PET bottle for juice or grain-based beverage is crystallized before blowing to improve heat resistance at the entrance of the bottle. However, residual stress, developed during injection molding of preform, prevents the crystallization. In order to release the residual stress in the preform, the preform is annealed after the injection molding. If the residual stress is reduced by optimizing the injection molding conditions of preform the annealing time would be shortened. In this study, the optimum conditions for minimizing the residual stress and increasing dimensional accuracy of the injection molded preform are suggested through CAE analysis. In order to optimize the molding conditions, minimizing residual stress and shrinkage, computer simulations have been carried out with help of design of experiment scheduling. Injection temperature, initial packing pressure and filling time were selected for control parameters. Residual stress was affected by injection temperature and filling time. Shrinkage was affected by injection temperature. It was found that maximum residual stress, distribution of residual stress and shrinkage were decreased by 22%, 40% and 25%, respectively at an optimum molding condition compared with the results of previous molding condition.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.1
• /
• pp.13-19
• /
• 2014

Three heat-treatment schedules were applied to $90{\times}90mm$ dimension square lumber of Pinus koraiensis, one of major domestic species, and their colors and physical properties were investigated for obtaining an optimum schedule. Each square lumber was heat-treated three times. The temperatures of $170^{\circ}C$ and $190^{\circ}C$, and the time of 9 hours and 13 hours were used for the first heat-treatment. The schedule of $190^{\circ}C$ and 7 hours were used for the next two heat-treatments. The averages of brightness $L^*$ decreased linearly as the heat-treatment repeated and its standard deviations also decreased slightly. While the averages of color difference ${\Delta}E^*$ increased linearly as the heat-treatment repeated and its standard deviations also increased slightly. The average compressive strength of the heat-treated specimen was higher than that of the control by 9%, which deviates from previous reports. ASE and WPG of the heat-treated specimens were measured to confirm that heat-treatment improved dimensional stability significantly.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.2
• /
• pp.145-151
• /
• 1997

In concrete mix design we need the informations of the codes, the specifications, and the experiences of experts. However we can't consider all factors regarding concrete mix design. The final acceptance depends on concrete quality control test results. In this process we meet the uncertainties of materials. temperature, site environmental situations, personal skillfulness. and errors in calculations and testing process. Then the mix design adjustments must be made. Concrete mix design and adjustments arc somewhat complicated, time-consuming. and uncertain tasks. In this paper, as a tool to minimize the uncertainties and errors the neural network is applied to the concrete mix design. Input data to train and test the neural network are obtained numerically from the results of design following the concrete standard specifications of Korea. The 28-days compressive strengths which are variate according to the uncertainties and errors are considered. The results show that neural networks have a strong potential as a tool for concrete mix design.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.821-824
• /
• 2008

In this study, it is willing to present that fundamental data for proposing quantitatively shrinkage cracking evaluation method such as plat-ring type restrained test method. It is possible to decide that specimen diameter is s 150mm with evaluating restrained shrinkage crack properties of concrete according to change of ring diameter in specimen. Also, effectiveness of test method according to mixing of PVA fiber is evaluated as part of a repeatability verification experiment of plat-ring type restrained test method using ring which diameter is 150mm. As a result, it is possible to measure the crack due to the plastic shrinkage which was occurred within 48hours at early age with plat-ring type restrained test method. Hereafter, it is considered that the study concerning environmental condition and mixing factor in plat-ring type restrained test method is need.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1581-1588
• /
• 2011

In this study, flow characteristics in a multi-cavity injection molding process were investigated. One of main problems occurred in the multi-cavity molding is a flow imbalance among cavities since it affects physical properties and quality of products. Charge imbalance is caused by the uneven shear stress. Therefore, changes in viscosity affect the physical properties of resin and injection conditions differ in the filling imbalance phenomenon. Through, this study focus on experimental studies of flow imbalance for PC and PP resin occurring in a balanced delivery system. Experimental results were compared with CAE results. By experimental and CAE analysis, main cause for the flow imbalance is temperature distribution in cross section of runner. New runner system with a simple change of runner shape was suggested to avoid the flow imbalance. A series of simulation to confirm feasibility of Volume Runner's effects was conducted using injection molding CAE.

• Polymer(Korea)
• /
• v.35 no.6
• /
• pp.599-604
• /
• 2011

The PET-PEN copolymers have been synthesized and the effect of their morphology on the physical properties of polyester flexible substrate was investigated. It was found that the block sequence of synthesized copolymer was varied depending upon DMT/NDC ratio in polymerization. Higher PET-PEN and PEN block sequence in polyester copolymer resulted in the increase of glass transition temperature and it caused the enhancement of dimensional stability as a polyester flexible substrate. The highest coefficient of thermal expansion(CTE) was obtained when DMT/NDC ratio is 50/50. Synthesized PET-PEN copolymer seems to be acceptable as a flexible substrate since it shows that their optical transmittance at 550 nm is over 80% and thermal weight loss at $280^{\circ}C$ for 1 hr is less than 0.4 wt%.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.1269-1273
• /
• 2005

자연 친화적 하천관리는 현 치수위주의 하천정비 관행으로 인한 하천의 환경 기능의 훼손을 막고, 제도적으로 자연 친화적으로 하천 사업을 추진하기 위해서 수변조사, 계획, 설계, 시공, 모니터링, 그리고 유지관리 등 일련의 체계적인 절차에 따라 하천 사업을 시행하는 것이다. 특히 이러한 표준 절차 가운데 수변조사는 하천의 특성을 결정짓는 여러 가지 자연적, 인공적 형성과정들과 그 과정들을 지배하는 생태학적 원리들을 파악하여 하천사업의 정비주제와 방향을 설정하는데 도움을 준다. 모니터링은 계획과 설계, 시공을 통해 실시된 하천사업의 효과를 평가하고, 공법적용에 따른 하천의 변화과정을 파악하여 유지관리 및 적응관리를 위한 근거를 제시하는 과정이다. 수변조사 및 모니터링 매뉴얼은 건설교통부가 수행한 '자연친화적 하천정비기법 개발' 의 연구성과로서, 경기도의 탄천, 충청북도의 달천 그리고 경기도 오산천을 대상으로 각 관련분야의 전문가가 참여하여 직접 적용$\cdot$검증한 결과를 바탕으로 제작한 것이다. 이는 하천의 관리 및 하천관련 사업을 자연 친화적으로 수행하기 위하여 필요한 '수변조사'와 '모니터링'에 대한 일반적인 절차와 방법을 체계화 한 것이다. 특히 수변조사 매뉴얼의 경우는 $\ulcorner$하천설계기준$\lrcorner$의 '제12장 하천환경조사'를 보완하는 관계에 있다. 하천설계기준에서 제시한 하천환경조사는 본 수변조사 매뉴얼상과 동일한 절차와 양식을 따르고 있다. 하천설계기준에서 자세하게 기술하지 못한 조사방법, 정리, 분석, 평가에 대한 내용을 구체적으로 적용하여 이를 보완하고 있다.은 안양천 웹페이지(http://anyang.river.or.kr)에서 구현되고 있으며, 앞서 설명한 바와 같이 1단계 프론티어 사업으로 설치된 4개의 하천수위, 2개의 지하수위 관측시설과 함께, 2단계에 (주)웹솔루스에서 자체적으로 설치 운영하고 있는 2개소의 하수관거 모니터링 관측시설, 그리고 안양시에서 운영하고 있는 5개소의 강우관측소와 7개소의 수위관측소를 모두 통합하여 실시간 자료를 제공하고 있다. 수위자료는 10분단위의 텍스트정보와 그래프형태로 지원되며, 검색기간 설정을 통해 원하는 기간내의 자료를 선별, 검색할 수 있다.. 또한 이와 같은 기초적인 정보를 바탕으로 하류하천의 탁수 피해를 최소화할 수 있는 선택취수탑의 운영방안을 수립할 수 있다 본 연구에서는 이를 위해 선택취수탑 주위의 성층흐름을 기존의 실험자료와 수치해석을 통하여 분석하였고, 온도성층구조나 취수구의 위치변화에 따른 방류수 수질특성을 조사하였다.쇄파대(artifical reef)와 같은 완충지대를 갖는 호안을 축조함으로써 월파량을 감소시키는 대안으로 제시하고자 한다. 본 연구 수행을 통해 태풍 내습시 발생 가능한 자연재해에 대한 사전 방지를 목적으로 태풍피해의 원인을 제시하고 이를 해결하여 현재의 방재대책이 항구적인 방재대책으로 전환될 수 있는 방안 마련의 기초 자료로 활용되기를 기대한다., L-arabinose, 및 D-galactose; 제3차(第三次) 가수분해물(加水分解物)(C)에서 L-rhamnose, D-xylose, L-arabinose 및 D-galactose, 비가수분해물(非加水分解物)(C')에서 D-xylose와 D-galactose를 검출(檢出)하였다. (4) 구성당(構

• Korean Journal of Materials Research
• /
• v.8 no.3
• /
• pp.206-213
• /
• 1998

Cu, Ni, and Mo were ion-diffused into the pure steel powder in the aqueous solution of $(CuNO_3)_2$, $Ni(NO_3)_2)_2$, and $(NH_4)_6Mo_7O_{24}$, to form partial diffusion bond prealloyed steel powder. The mechanical properties, and compacting and sintering characteristics were investigated as a function of Cu. Ni and Mo contents. The results of the this research, it was found that the smallest change of size was observed, and the good degree of hardness and tensile strength was observed when 1.50wt%Cu, 1.75wt%Ni and 0.50wt%Mo was added each other. The powder metallurgy characteristics of partial diffusion bond prealloyed steel powder containing 1.50wt% of Cu, 1.75wt% of Ni and 0.5wt% of Mo were compared to those of distalloy $AB\textregistered$ which was manufactured in Hogani Corporation of Sweden. Partial diffusion bond prealloyed steel powder of this study had good degree of hardness and density, and its dimensional stability was same to that of pure steel powder. Under the same sintering density and temperature, the tensile strength of the ion powder from this research was $15~20Kg/\textrm{mm}^2$ larger than that of distalloy AB'. also the hardness was larger in the magnitude of Hv20-30. When the powder metallurgy heat-treated, hardness and tensile strength were substantially increased.

• Journal of Korean Society of Forest Science
• /
• v.36 no.1
• /
• pp.26-32
• /
• 1977

Press drying was used on sapwood and heartwood of oak (Qercus acutissima Carruthers) to find profitable means of drying low grade logs. This study was designed to investigate the process of press drying considering core temperature, current moisture content, drying rate, drying time, final moisture content, dimensional change and drying defects. The drying tests were conducted using 1.5 centimeter thick material at platen temperature of $175^{\circ}C$ and pressure of 35psi. The results were summarized as fallows. 1. Core temperature was divided into three stages of drying characterized by initial heating period, plateau temperature, and period of rising core temperature. Plateau temperature of heartwood material was higher and longer than that of sapwood material. 2. The predicting equation for change in drying rate of sapwood material was log y=-2.7925-0.0811x as function of time. That of heartwood material was log y=-3.3382-0.0468x. 3. Sapwood material reduced the moisture content from 59 to 2.5 percent in 45minutes. Heartwood material reduced the moisture content from 64 to 3.3 percent in 55 minutes. 4. Shrinkage during press drying were 20.4 percent in thickness direction and 2.5 percent in width direction. Recovery on equilibrium conditioning at 65 percent relative humidity and temperature of $20^{\circ}C$. were 11.4 percent in thickness direction and 49.4 percent in width direction. 5. Heartwood material developed severe honeycombing and moderate checking. The sapwood material dried without honeycombing, checking and collapse. All material kept wood flat.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.115-122
• /
• 1996

Heat transfer characteristics of low temperature latent heat storage systems have been examined for the circular finned and unfinned tubes using Na$_2$B$_4$O$\_$7/10H$_2$O as a phase change material. In order to reduce the supercooling of PCM, 3 wt% of Na$_2$B$_4$O$\_$7/10H$_2$O was added as the nucleating agent and 2.2 wt% of acrylic acid sodium sulfate was used as the thickener. The heat storage vessel has dimension of 530 mm height, 74 mm 1.D. and inner heat transfer tube is 480 mm height and 13.5 mm O.D. Water was employed as the heat transfer fluid. During the heat recovery experiment, the heat recovery rate was affected by the flow rates and inlet temperature of heat transfer fluid. The enhancement of heat transfer by fins over the unfinned tube system was found to be negligible in the thin finned tube systems, whereas the heat transfer coefficient in the thick finned tube system is approximately 60% higher than that in the unfinned lobe system. The experimentally determined heat transfer coefficient for the unfinned tube and thick finned tube systems are 150-260 W/㎡$^{\circ}C$ and 230-530 W/㎡$^{\circ}C$, respectively. The fin efficiency based on the heat transfer coefficient and area increased by fins was found to be 0.05 and 0.26 for the thin and the thick finned tube systems.