• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.2004-2011
• /
• 2004

The applicability of the ultrasonic C-scan inspection is restricted due to the deterioration of mechanical properties of specimen during the test. Therefore, the aim of this research is applied to Eddy Current (EC) test substitute for the C-scan inspection in CFRP tube containing defects. This research is to evaluate the EC signals for the inspection of CFRP tube containing various circular hole defects (20% to 100% depth to the specimen thickness) using the unloading specimen and radial loading specimen. This study was considered the following points; 1) Analysis of EC signals for the inspection of saw-cut defect and circular hole defect, 2) The evaluation of defect depths and EC signals relationship. 3) Variation of EC signal owing to the radial load. In conclusions, the high frequency such as 300∼500 kHz made it possible to the inspection of 40% to 100% defects. Particularly, in case of 20% defect, the EC signal was not detected due to the noise of micro-crack and delamination. While the depth of the hole defects were decreasing, the difference of the phase angle between unloading specimen and radial loading specimen was gradually increasing.

• Tribology and Lubricants
• /
• v.26 no.6
• /
• pp.341-345
• /
• 2010

The NAUT(Non contact Air coupled Ultrasonic Testing) is one of the ultrasonic wave inspection methods. It compensates High power ultrasound Pulser Receiver, pre-amp, air probe of high sensitivity in air to generate loss energy by NAUT methods. Generally, in case of ultrasound inspection, it applies contact methods by using couplant. However it can inspect of UT without couplant by this NAUT. The ultrasound transmission reception is composed in stable condition in NAUT. It can inspect high low material or the specimen of rough part, the narrow spot, too. The spot welding is applying the inosculation of automobile component, car body, all boards. The CFRP is necessity of NDE because of the solidity changes material according to lamella tearing. Therefore it checked on realization whether and commercialization in the spot welding and CFRP inspection that the NAUT would be applied them.

• Journal of the Korean Ceramic Society
• /
• v.19 no.3
• /
• pp.199-204
• /
• 1982

Bowl 형태의 일본산 Nagano 점토에 대한 분류 및 특성화 연구를 하였다. 결정입자 크기를 1$\mu$ 이하로 침강분리 시킨후 전자현미경으로 결정형태를 관찰하였다. 아울러 결정형태, 구조적 결함 및 intercalation 반응성의 상호관계를 검토하기 위하여 tube 형태의 한국산 halloysite 및 plate 형태의 kaolinite를 비교 조사하였다. 특이한 Bowl 형 Nagano 점토는 tube형 halloysite와 화학 반응성에서 동일하여 극성 내지는 hydrogen bridge 결합을 하는 guest 분자와 반응하여 층간삽입 화합물을 형성 하였다. 화학반응성에 따른 점토분류방법에 의해 Nagano 점토가 halloysite임을 밝혔으며 아울러 결정의 형태는 반응성에 영향을 미치지 않음을 알 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.367-369
• /
• 2009

플렉서블 태양전지용 연성기판재에는 플라스틱재와 금속재가 있다. 기존의 연성기판인 플라스틱의 경우 열과, 내구성, 화학약품에 약하다는 단점이 있으며, 금속기판은 높은 생산원가, 박판화의 어려움 등의 문제를 안고 있다. 일반적으로 기판재와 cell을 구성하는 반도체 층의 열팽창 거동 차이에 의한 열 변형이 태양전지의 공정안정성에 영향을 주는 것으로 알려져 있으며, cell을 구성하는 반도체 층과 열팽창 거동이 유사한 금속기판재의 적용이 필요하다. Si 박막 태양전지의 경우 Si 열팽창 거동과 비슷한 특성을 갖는 기판재의 개발이 필요하다. 전주법을 적용하여 조성이 다른 Ni계 합금의 열팽창 거동을 TMA 장비를 사용하여 측정하였다. 그리고 전산해석 Tool을 활용하여 가상의 Si 박막 태양전지 제조공정을 설정하고 고온 공정온도에서 상온으로 냉각시 발생되는 층간 열변형 연구를 수행하였고 열팽창 거동이 다른 합금 상에 Si층을 증착하여 열 충격에 의한 결함 발생여부를 관찰하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3202-3218
• /
• 1994

Mode shapes and natural frequencies of vibrating laminated composite plates are taken using real-time and time-average holographic interferometry. Debonds and delamination in the laminated plates are measured nondestructively. During holographic testing of composite plates, it has been found that the conditions for the local resonance in debonds are strongly dependent on the frequency of excitation. A membrane resonance model was proposed to describe this behavior. Relations between characteristic length according to the size, shape of debonds and membrane resonance frequency are presented. Several experiments were performed to verify the membrane resonance model. The agreements between the predicted excitation frequency and the observed resonance frequency are good. The experimental results show that higher stresses and strains due to local resonance lead to the debond detection.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.401-407
• /
• 2017

This paper describes wavenumber filtering for damage detection using single-frequency standing wave excitation and laser scanning sensing. An embedded piezoelectric sensor generates ultrasonic standing waves, and the responses are measured using a laser Doppler vibrometer and mirror tilting device. After scanning, newly developed damage detection techniques based on wavenumber filtering are applied to the full standing wave field. To demonstrate the performance of the proposed techniques, several experiments were performed on composite plates with delamination and aluminum plates with corrosion damage. The results demonstrated that the developed techniques could be applied to various structures to localize the damage, with the potential to improve the damage detection capability at a high interrogation speed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.3 s.258
• /
• pp.344-354
• /
• 2007

The objective of this study is to investigate the effect of arbitrarily located defect around the circular hole in the aircraft structural material such as Al/GFRP laminates and monolithic Al alloy sheet under cyclic bending moment. The fatigue behavior of these materials may be different due to the defect location. Material flaws in the from of pre-existing defects can severely affect the fatigue crack initiation and propagation behavior. The aim of this study is to evaluate effects of relative location of defects around the circular hole in monolithic Al alloy and Al/GFRP laminates under cyclic bending moment. The fatigue behavior i.e., the stress concentration factor($K_t$), the crack initiation life($N_i$), the relationship between crack length(a) and cycles(N), the relationship between crack growth rate(da/dN) and stress intensity factor range(${\Dalta}K$) near a circular hole are considered. Especially, the defects location at ${\theta}_1=0^{\circ}\;and\;{\theta}_2=30^{\circ}$ was strongly effective in stress concentration factor($K_t$) and crack initiation life($N_i$). The test results indicated the features of different fatigue crack propagation behavior and the different growing delamination shape according to each location of defect around the circular hole in Al/GFRP laminates.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.4
• /
• pp.125-133
• /
• 2016

From the first application of a thermoelectric module to nowtoday, it has been more than half a century. The application of a thermoelectric module is becoming more and more widely accepted since, people's requirement rely more and more on the efficiency of thermoelectric modules and their reliability become higher and higher. So people pay more and more attention to the thermoelectric module. In Around the world, the more research for into improving the efficiency of thermoelectric modules is focused on the current materials. at present. However, the research of into available materials had has some limitations, and the research of materials had reached a bottleneckthere are limits to current applications. On the other hand, from the production process, if we assembled by materials withoutmodules without any damages and achieve the ideal state of a joint, we can make the a product to maximize performance and have a longer service life. SoTherefore, in this study we will prove the relationship between the any defects inside and the efficiency of a thermoelectric module to improve the quality management and performance of modern thermoelectric modules at present.

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.307-318
• /
• 1999

동결건조법에 의한 저유전성 실리카 박막의 제조공정 개발 및 층간 절연물질로의 응용성이 연구되었다. 코팅용 폴리머 실리카 졸은 TEOS와 이소프로판올(iso-propanol:IPA)또는 터트부탄올(tert-butanol:TBA)을 용매로한 2단계 공정에 의하여 제조되었으며, 이들 졸을 p-Si(111)웨이퍼 상에 스핀코팅한 습윤겔 박막을 동결건조 하여 다공성 실리카 박막을 제조하였다. 균일한 박막 코팅층을 얻을 수 있는 실리카 졸의 최적 점도범위는 IPA와 TBA를 용매로 한 실리카 졸의 경우 각각 10~14 cP와 20~30cP 정도였으며 스핀속도는 2000 rpm 이상이었다. 결함이 없는 다공성 실리카 박막은 TBA(빙점 $25^{\circ}C$)를 동결용매로 하여-196$^{\circ}C$까지 급랭시킨 후 $0^{\circ}C$와 0.1 torr 까지 가열 감압한 상태에서 고상의 TBAFMF 모두 제거한 다음 20$0^{\circ}C$까지 열처리하여 제조되었다. 다공성 실리카 박막의 두께는 졸의 타입과 스핀코팅 속도에 의해 2500~15000$\AA$범위 내에서 제어가 가능하였으며 이들 막의 밀도와 유전상 수 값은 각각 0.9$\pm$0.3g/㎤(기공율 60$\pm$10%)과 2.4 정도였다.

• Journal of the Korean Vacuum Society
• /
• v.10 no.4
• /
• pp.403-410
• /
• 2001

Acceleration in integration density and speed performance of ULSI circuits require miniaturization of CMOS and interconnections as well as higher current density capabilities for transistors. A leading candidate to substitute Al-alloy is Cu, which has lower resistivity and higher melting point. So we can expect much higher electromigration resistance. In this paper, we are going to explain the major features of EM for MOCVD Cu according to variant conditions. We compared the life time and activation energy of MOCVD Cu with those of I-beam Cu and AA in the same conditions. The electromigration experiments were performed with Cu/Al/TiN multilayer. Experimental results shows that the deposition rate and electromigration characteristics of Cu thin film were improved by the Al interlayer.