• Journal of Convergence for Information Technology
• /
• v.9 no.7
• /
• pp.94-99
• /
• 2019

Friction stir welding was first reported by TWI(The Welding Institute) in 1991, and this welding method has been rapidly used in various industrial areas such railway, automobile, aerospace and shipbuilding industry. Here, we study core characteristics of friction stir welding (FSW) applied to Al 6005-T6 extruded sheets, which is the typical alloy used for railway car bodies. With the fixed welding speed of 500 mm/min, the rotating tool speed was varied from 600 to 1800 RPM. The results of hardness measurement revealed that the hardness of nugget area is ~70% with respect to the parent material, and for the selected range of rotation speed, no clear dependence was observed and the hardness values close to the parent materials were achieved for the area located 5 mm away from the welding interface. The tension test shows that yield strength and tensile strength were slightly decreased with increasing RPM, with no observed difference for the elongation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.71-74
• /
• 1996

절삭가공 중에서 구멍가공은 최근 광범위하게 이루어지는 작업의하나이다. 현재 대부분의 구멍가공은 두개의 절삭날을 갖는 Twist Drill에 의해 이루어지고 있다. 이 두개의 절삭날 드릴은 작업능률이 다른 절삭 공구에 비교하여 낮고, 그 가공정도도 충분하지 않다. 본 연구에서는 초경 세개의 절삭날 드릴을 사용하여 구멍가공 실험을 하고, 그 절삭성능과 관련하여가공 구멍의 형상을 측정함에 따라 가공구멍 중심축의 기울어짐, 진원도 및 표면거칠기를 연구하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.58-63
• /
• 1995

절삭가공 중에서도 높은 비중을 차지하는 구멍가공은 전자제품, 공작기계 뿐만 아니라 산업 전반에 걸쳐 소형 화, 다양화, 대량생산화 함에 따라 미세화, 고속화하게 되었다. 본 연구에서는 미세드릴 가공시에 발생하는 스러스트를 측정하여 이송, 절삭속도, 피삭재 두께 변화 등 각 절삭조건이 공구수면과 가공확대오차에 미치는 문제점을 해결하기 위한 방안으로 스텝이송 방식을 채택하여 그 효과에 대한 평가를 목적으로 한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.261-261
• /
• 2004

본 논문에서는 고속가공 시 필랫(코너-R) 엔드밀의 곡면가공 적용가능 여부를 연구하기 위하여 비교적 곡률이 완만한 곡면을 채택하여 가공실험을 수행하고 고 결과를 분석하였다. 가공재료는 금형의 재료로 많이 사용되는 SKD11 강을 선택하였다. 볼엔드밀과 필렛엔드밀의 비교를 위하여 2 종류의 공구에 동일한 가공조건으로 가공실험 하였다. 가공 중 측정된 절삭력과 가공면의 표면조도를 분석하여 일반적으로 황삭에서 주로 사용되던 필렛엔드밀을 곡률이 완만한 곡면의 정삭에 적용하였을 경우의 절삭특성과 볼엔드밀의 가공특성을 비교하였다.(중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.184-184
• /
• 2004

볼 나사는 반도체ㆍLCDㆍPDP 등 전자제품 조립장비 제조업체와 CNC 공작기계, 정밀측정기계, 직교좌표로봇, 반송장치, 항공기용 유압구동장치 대체품, 전동공구, 파워 steering, 테이블 개폐장치 등에서 구동 장치 및 물품의 이송을 위해 대부분 사용되는 중요한 기계요소 중의 하나이다. 그것은 회전운동을 직선운동으로 전환해주는 기구부에 들어가는 가장 중요한 부품이며, 원통형의 봉에 나선형의 그루브를 가공한 장축의 나사와 단축의 너트 사이에 볼을 게재시켜 축의 회전 시 적은 구름마찰로 인해, 너트부가 직선 운동하는데 원활 하게 만들어진 기계요소이다.(중략)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.6
• /
• pp.860-866
• /
• 2004

In the end milling operation the deflection of the cutter is an important factor affecting the accuracy of machining, with implications on the selection of cutting parameters and economics of the operation. Several studies were devoted to the end mill deflection and its effects, notably, providing a useful insight into the problem. Although the deflection affects adversely the accuracy, the flexibility of the cutter is beneficial in attenuating the overload in a sudden transient situation, as well as in attenuating chatter. The deflection of the end mill was studied both experimentally with strain gauge, tool dynamometer, laser measuring apparatus and on a finite element model of the cutting using ANSYS software. The deflection of machining tool with various helix angles was studied with FEM simulation and experiment. ANSYS analysis performed on the finite element model of the end mill provides deflection results which agree within 15.0% with the experimental ones.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.3 s.20
• /
• pp.44-50
• /
• 2003

An experiment is conducted for measuring the performance of an air tool, which is operated at 100,000 RPM in an unloaded state with very low torque. A 551 kPa in gauge pressure is supply to the inlet of an air tool. An experimental apparatus is developed as a friction type dynamometer. Inlet total pressure, air flow rate, rotational speed and operating force are measured simultaneously. Torque, output power and specific output power are obtained with different rotational speeds. Those are compared with the experimental results which were obtained by a commercial dynamometer. However, no commercial dynamometers are available for measuring the torque above 30,000 RPM. In order to reduce the rotational speed, a reduction gear is applied between the air tool and the commercial dynamometer. Torque and power obtained by the commercial dynamometer show $55\%$ lower than those obtained by the developed friction type dynamometer, because the mass is added to the rotor of air tool for the braking system of the commercial dynamometer and power loss is generated by the reduction gear. From the compared results, the friction type dynamometer should be applied for measuring the performance of the air tool operating at low torque and high RPM.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.5
• /
• pp.450-461
• /
• 1984

A new indirect tool wear sensing technique is proposed using time series analysis. The acceleration measured on the tool post in the vertical direction during turning is sampled with uniform interval, and fitted following the ARMA modeling procedures. Various signal characteristics are observed in respect with the progress of flank wear. From those observations it is believed that; *The variance of the signal is approximately proportional to the increase of flank wear. *The absolute power of a dynamic mode decreases in the beginning of cutting until the maximum flank wear increases up to 0.4-0.5mm, and then increases. *The other characteristics are not so much related to the tool wear as the signal variance and the absolute power of a dynamic mode. Hence, the absolute power of a dynamic mode seems to be a good factor for the indication of tool-change time regardless of tool material or cutting conditions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.130-130
• /
• 2018

산업 발전으로 특수합금들이 발달함에 따라 가공할 수 있는 새로운 절삭공구소재들이 개발되어지고 있다. 또한 공구소재보다 코팅개발이 상대적으로 더욱 효과적이기 때문에 코팅 기술 개발이 활발히 진행되고 있다. 일본에서는 새로운 코팅층 물질 개발보다는 기존의 코팅물질을 조합하거나 개량하여 성능을 향상시키는 추세이다. TiAlSiN 박막은 스퍼터링과 음극 아크 소스를 이용한 hybrid 공정을 이용하여 코팅 후 특성을 평가하였다. Ti-50at.%Al의 조성을 갖는 TiAl 합금 타겟은 음극 아크 소스를 이용하여 코팅하였다. 공정 가스는 Ar과 N2의 혼합 가스를 사용하였으며 공정 압력은 $1.0{\times}10^{-2}Torr$이었다. 음극 아크 소스에 인가된 전류는 70 A이었다. TiAlSiN 박막의 Si 함량을 조절하기 위해서 Si은 스퍼터링으로 코팅하였으며 스퍼터링 소스에 인가되는 전력의 세기를 0.29 kW ~ 1.05 kW까지 변화시켰다. 코팅 공정에 사용된 Si 타겟의 순도는 4N이다. TiAlSiN 박막의 Si 함량은 스퍼터링 전력에 따라 3.4 ~ 14.4at%까지 변화하는 것을 확인하였다. TiAlSiN 코팅층의 경도는 초미소 경도계를 이용하여 측정하였으며, Si 함량이 증가하면 TiAlSiN 박막의 경도도 증가하는 것을 확인할 수 있다. TiAlSiN 박막의 Si 함량이 9.2at.%일 때 3000 Hv 이상의 경도를 보였다. TiAlSiN 코팅층의 Si 함량이 14.4at%로 높아지면 경도가 낮아지는 현상을 보였다. TiAlSiN 박막의 Si 함량이 증가하면 내산화성이 향상되는 현상을 확인할 수 있었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1066-1069
• /
• 2004

Recently the monitoring system of tool setup in high speed precision machining tool is required for manufacturing products that have highly complex and small shape, high precision and high function. It is very important to reduce time to setup tool in order to improve the machining precision and productivity and to protect the breakage of cutting tool as the shape of product is smaller and more complex. Generally, the combination of errors that geometrical clamping error of fixing tool at the spindle of machining center and the asynchronized error of driving mechanism causes that the run-out of tool reaches to 3∼20 times of the thickness of cutting chip. And also the run-out is occurred by the misalignment between axis of tool shank and axis of spindle and spindle bearing in high speed rotation. Generally, high speed machining is considered when the rotating speed is more than 8,000 rpm. At that time, the life time of tool is reduced to about 50％ and the roughness of machining surface is worse as the run-out is increased to 10 micron. The life time of tool could be increased by making monitoring of tool-setting easy, quick and precise in high speed machining center. This means the consumption of tool is much more reduced. And also it reduces the manufacturing cost and increases the productivity by reducing the tool-setup time of operator. In this study, in order to establish the concept of tool-setting monitoring the measuring method of the geometrical error of tool system is studied when the spindle is stopped. And also the measuring method of run-out, dynamic error of tool system, is studied when the spindle is rotated in 8,000 ∼ 60,000 rpm. The dynamic phenomena of tool-setup is analyzed by implementing the monitoring system of rotating tool system and the noncontact measuring system of micro displacement in high speed.