• Laser Solutions
• /
• v.12 no.1
• /
• pp.1-6
• /
• 2009

최근, 전자, 디스플레이, 반도체 등 여러 분야에서 광학적, 기계적 등의 성질이 우수한 유리와 세라믹 재료의 사용이 급증하고 있다. 이러한 취성 재료의 절단가공에 있어서 전통적인 기계적 방식은 미세균열로부터 자유로울 수 없다는 한계를 지닌다. 따라서 레이저로 열응력을 발생시켜 재료를 절단하는 controlled fracture 레이저 절단공정은 기존 공정을 대체하는 새로운 기술로 각광받고 있다. 따라서 controlled tincture에 대하여 많은 연구가 진행되고 왔으며 현재에도 다양한 새로운 공정이 개발되고 있다. 하지만 아직도 열응력에 의해 재료가 변형, 절단되는 물리적인 메커니즘이 명확히 규명되어 있지 않을 뿐 아니라 레이저 광원, 냉각방식 및 각종 공정변수가 절단 품질에 미치는 영향도 체계적으로 분석되지는 못한 실정이다. 따라서 보다 효과적인 공정개발을 위해서는 추후 더욱 심도 있고 많은 연구가 수행되어야 할 것으로 판단된다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.6
• /
• pp.501-517
• /
• 2011

In general, the tunnel stability during excavation is assessed by comparing measured displacements at roof and sidewall to control criteria. The control criteria were established based on the past experience that considered ground conditions, size of the tunnel cross section, construction method, supports, etc. Therefore, a number of researches on the control criteria using the critical strain have been conducted. However, the critical strain obtained from uniaxial compression tests have drawbacks of not taking damage in rock mass due to increase of stress level and longitudinal arching into account. In this paper, damage-controlled tests simulating stress level and longitudinal arching during tunnel excavation were carried out in addition to uniaxial compression tests to investigate the critical strain characteristics of granite and gneiss that are most abundant rock types in Korean peninsula. Then, the critical strains obtained from damage-controlled tests were compared to those from uniaxial compression tests; the former showed less values than the latter. These results show that the critical strain obtained from uniaxial compression tests has to be reduced a little bit to take stress history during tunnel excavation into account. Moreover, the damage critical strain was proposed to be used for assessment of the brittle failure that usually occurs in deep tunnels.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.11
• /
• pp.5-10
• /
• 2023

Slag-CB is widely used in various fields that require groundwater control. It is a type of CB where a portion of the cement mixed with CB is replaced with GGBS. In general, Slag-CB has the advantage of long-term improvement in compressive strength, permeability, durability, and chemical resistance as the GGBS replacement ratio increases. However, there are problems such as decreased flexibility and resistance to deformation of the cut-off walls, as well as brittleness upon failure. To address these problems, some quality standards recommend designing Slag-CB with lower strength, which makes it challenging to apply high-strength Slag-CB with a high GGBS replacement ratio in the field.In this study, we aimed to improve the flexibility and resistance to deformation of Slag-CB to prevent brittle failure and improve the field applicability of Slag-CB. To achieve this, we evaluated the compressive behavior of nylon fiber-reinforced Slag-CB and proposed measures for enhancing the flexibility and resistance to deformation of Slag-CB.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.4
• /
• pp.23-32
• /
• 1999

Behavior of H-beam connections under cyclic loadings is investigated experimentally in this study. The purpose of this study is to study the effect of steel properties and coping shape on the hysteretic behavior of H-beam connections. Five beam-to-column connection specimens were fabricated and tested under cyclic loadings. The load-rotation curves of the beam connections were mainly obtained. Deformation capacity and energy dissipation capacity of the connections are compared each other. The connections fabricated from SS400 showed good deformability and energy dissipation capacity, but those from SM490 showed brittle fracture at the connection. The coping shape at the connections showed a little difference in cyclic behavior.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.529-537
• /
• 2007

The purpose of this study is to discuss how strength and ductility of each system in low-rise reinforced concrete buildings composed of extremely brittle, shear and flexural failure lateral-load resisting systems have influence on seismic capacities of the overall system, which is based on nonlinear seismic response analyses of single-degree-of-freedom structural systems. In order to simulate the triple lateral-load resisting system, structures are idealized as a parallel combination of two modified origin-oriented hysteretic models and a degrading trilinear hysteretic model that fail primarily in extremely brittle, shear and flexure, respectively. Stiffness properties of three models are varied in terms of story shear coefficients, and structures are subjected to various ground motion components. By analyzing these systems, interaction curves of demand strengths of the triple system for various levels of ductility factors are finally derived for practical purposes. The result indicates that demand strength levels derived can be used as a basic information for seismic evaluation and design criteria of low-rise reinforced concrete buildings having the triple lateral-load resisting system.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.2
• /
• pp.33-56
• /
• 2001

It is well known fact that all rocks exhibit brittle properties and time depends strain properties (creep). An understanding of the time dependent deformation behaviour of rocks is believed to be essential in the field of civil and tunnelling. The rock and concrete creep in various forms of loading conditions and physical environment are reviewed. A comparison of creep behaviour between rocks and concrete is provided, in order to bring two existing relatively independent methods of predicting creep strain closer together. It was felt that the physical process in the creep of rocks would be similar to the process in creep of concrete. Since experiments and observations have shown that non-elastic (creep) mechanical behaviour of all crystalline solids (i.e., concrete, rocks, ceramics and refractories) and single materials have a common base. Also a comparison of the results for the accepted methods of estimating creep in rocks and concrete under - multiaxial loading was attempted to extend the knowledge of deformational characteristics of these two materials.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.368-369
• /
• 2003

선진 복합재료의 매트릭스 수지로서 자장 많이 사용되고 있는 에폭시는 수지 및 경화제의 종류에 따라 여러 가지 물성을 나타낼 수 있다. 에폭시 수지는 기계적 물성 및 내화학성이 우수하고 경화시 수축변형이 적은 장점이 있으나 높은 가친밀도 때문에 순간적인 충격에 취약하다는 단점을 지니고 있다. 따라서 이러한 에폭시 수지의 취성 (brittleness)을 개선하기 위해 충격강도를 증가시킬 수 있는 강인화제를 혼합하여 경화시키는 방법이 사용되고 있다[1]. (중략)

• Magazine of the Korea Concrete Institute
• /
• v.14 no.2
• /
• pp.37-44
• /
• 2002

콘크리트의 내화성능에 대한 다각적인 연구가 1970년대부터 원자로의 안정성 확보차원에서 진행되어 왔으며 특히 콘크리트의 취성파괴(brittle failure)등에 대한 연구가 많다. 콘크리트의 내화성이란 화재로부터 보호되고 고열환경에 견디는 재료적 특성 즉 화재온도 1,00$0^{\circ}C$ 정도의 고온을 30분에서 3시간 정도를 받은 경우 콘크리트 중에 매립된 철근 등 철강을 소정의 온도 이하고 유지하기 위한 피복 역할을 유지하면서 구조물의 큰 변형이나 붕괴 등을 막기 위한 소요 압축강도 및 영계수 등의 성능을 가지고 있는 성질을 말한다.(중략)

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.509-510
• /
• 2009

In strengthening reinforced concrete beams using fiber reinforced polymer sheets, brittle structural failures occur due to the linear stress-strain relationship of the fibers. Hybrid fiber reinforced polymer sheets using two different types of fibers were investigated in this study

• Magazine of the Korea Concrete Institute
• /
• v.10 no.3
• /
• pp.107-115
• /
• 1998

반복하중을 받는 무근 및 철근 콘크리트 부재는 하중의 반복작용에 의해 과도한 균열 및 처짐을 유발하고 결과적으로 전체 구조요소의 파괴를 일으킨다. 따라서 하중반복에 의한 누적손상의 진행과정을 정량적으로 평가하여 철근콘크리트 보의 사용성과 안전성을 평가하는 것이 중요하고 특히 취성적 거동 특성을 갖는 전단거동의 경우에 더욱 의미가 있다. 본 연구에서는 반복전단하중에 의한 누적손상의 정량적 분석을 위하여 평균변형도 및 평균응력개념에 기초한 수정압축장이론(modified compression field theory)에 의하여 누적손상 모델을 제안하였다. 본 연구에서 제안된 모델을 통하여 반복전단하중에 의한 처짐과 변형도의 변화를 평가하는데 유용하게 이용될 것으로 사료된다.