• Journal of the Korean Society for Railway
• /
• v.13 no.5
• /
• pp.476-480
• /
• 2010

In the corrugated steel panels used for railway vehicles, sound insulation performance is significantly deteriorated by local resonance effect. In this study, as a countermeasure, polyurethane foam is filled in the corrugated steel panel and glass wool layer is inserted in the layered floor panel, and then improvement effect of the sound insulation performance is experimentally estimated. Based on ASTM E2249-02, intensity transmission loss is measured and estimated on the corrugated panel and floor structure. The aim of the study is to identify how the foam filling and inserting glass wool layer improve the sound insulation performance of the train body structure in aspect of the weight increment.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.253-259
• /
• 2021

Plastic wastes generated from household waste are separated by mixed discharge with foreign substances, and recycling is relatively low. In this study, the effect of the ratio and content of mixed plastic waste coarse aggregate(MPWCA)s and mixed plastic waste fine aggregate(MPWFA)s filled with blast furnace slag fine powder on the slump and compressive strength of concrete was evaluated experimentally. The MPWCAs were found to have a similar fineness modulus, but have a single particle size distribution with a smaller particle size compared to coarse aggregates. However, the MPWFAs were found to have a single particle size distribution with a larger fineness modulus and particle size compared to fine aggregates. Meanwhile, the effect of improving the density and filling pores by the blast furnace slag fine power was found to be greater in the MPWFA compared to the MPWCA. As the amount of the mixed plastic waste aggregate(MPWA)s increased, the slump and compressive strength of concrete decreased. In particular, the lower the slump and compressive strength of concrete was found to decrease the greater the amount of MPWFA than MPWCA when the amount of MPWA was the same. This is because of the entrapped air and voids formed under the angular- and ROD-shaped aggregates among the MPWFAs. On the other hand, the addition of the admixture and the increase in the unit amount of cement were found to be effective in improving the compressive strength of the concrete with MPWAs.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.06a
• /
• pp.156-159
• /
• 2000

경량소재로 사용되는 polyurethane은 난연화 및 강도유지를 위해 난연제, 섬유 및 무기충진제 등을 첨가하거나 고밀도화하여 사용하며 발포시켜 경량화하여 성형된다. Polyurethane 발포체는 자동차 내장재, 건축 구조재, 건축 내외장재, 가구재, 포장재료, 신발, 의류 제품, 단열재 등 다양하게 사용되고 있다. 이러한 polyurethane 발포체는 제조 및 가공의 편리함에 비해 화재발생시 연기발생량이 많고 연소가 용이하여 화재를 전파하는 매개물의 역할을 하여 피해를 더욱 가중시키는 취약점을 가지고 있다. (중략)

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2001.10a
• /
• pp.25-36
• /
• 2001

록볼트의 작용효과는 지반이 굴착되어 안정화되는 초기 1달간이 가장 중요하고 품질관리 문제는 지반조건에 따라 부식에 대한 문제가 있으나, 기존의 전면접착형 록볼트의 경우도 작업여건상 그 확실성은 떨어지는 것이 현실이다. 또한 작업이 시간소모가 크고, 볼트의 지지효과도 충진재가 고결되어야 발효되는 약점을 갖고 있어, 일본, 말레이시아, 유럽 등에서 전면 마찰형 즉시 지보기능이 가능한 Swellex Bolt를 영구지보재로 사용하고 있는 경향이 있다. 기존의 전면 접착형 SN Bolt(이형철근)로써 Grouting 몰탈볼트와 Cem Bolt로 설계된 장대·대단면 도로터널 지보재를 현대식 Swellex Bolt로 대체 설계변경이 가능한 것인지에 대하여 볼트의 지지력 시험(Pullout Test), 볼트재질의 내구성 연구 및 설계변경에 따른 수치해석 등을 실시하여, 볼트로써 지지력을 확인하고, 재질의 안전성을 조사한 후 시공 사이클 타임을 줄이며, 견고하고 시공성이 우수한 Swellex Bolt로의 설계변경을 제안하게 되었다.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.19-24
• /
• 2003

Potential applications of foam-filled section are the automotive structures. A foam-filled section can be used for the front rail and firewall structures to absorb impact energy during frontal or side collision. In the case of side collision where bending is involved in the crushing mechanics, the foam filler will be significant in maintaining progressive crushing of the thin-walled structures so that more impact energy can be absorbed. In this study, the manufacturing process of closed cell aluminum alloy foam filled stainless steel tube was studied, and the various foam filled specimens including piecewise fillers were prepared, tested and discussed about the bending behaviors.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1988.11a
• /
• pp.49-56
• /
• 1988

자동차의 동력전달 수단으로 사용되는 클러치는 그 기능에 따라 수동식과 자동식으로 구분된다. 전자의 경우 transmission과 engine의 동력을 dry contact mechanism으로 단속 제어하는 반면 후자는 hadraulic torque drive와 engine의 동력을 transmission box내의 기어유에 의한 wet contact mechanism으로 단속 제어한다. 자동식 클러치에 사용되는 paper facing은 cellulose fiber를 기본으로 하여 열경화성 수지 및 무기충진제등을 함유하고 있으나, 특히 무기충진제의 종류 및 첨가량이 paper facing의 마찰특성에 크게 영향을 미친다. 본 연구는 목재펄프(wood pulp), 린터펄프(linter pulp)등의 펄프를 주체로 하고 열경화성 수지와 무기충지제등을 첨가한 마찰재를 제조하여 무기충진제들의 마찰특성에 미치는 영향을 조사함으로써 paper facing의 기초 자료를 얻는데 그 목적이 있다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.1
• /
• pp.53-58
• /
• 2000

In this paper, the variable mechanical strength and dielectric breakdown strength of epoxy composites were measured at boiling absorption condition in order to observe the influences of moisture in out door use. Also, in order to improve water resistance of matrix resin, IPN(interpenetrating polymer network) method which had been already reported, was introduced and the influence was investigated. As Adding filter(SiO2) classified by o[phr], 50[phr] and 100[phr] to two kinds of matrix resin, six kinds of specimens were manufactured. As a result, it was confirmed that the moisture absorption rate was increased and mechanical strength and dielectric breakdown strength were degraded with boiling time and filler content increasing. On the other hand, it was confirmed that moisture absorption rates were decreased and the degrading rates of mechanical strength and dielectric breakdown strength were lowered according to improvement of adhesion strength in case of IPN specimens.

• Composites Research
• /
• v.23 no.4
• /
• pp.35-43
• /
• 2010

The purpose of this paper is to develop a Hybrid Fiber-reinforced High Strength Lightweight Cementitious Composite (HFSLCC) incorporated with lightweight filler and hybrid fibers for lightness and high ductility. Optimal ingredients and mixture proportion were determined on the basis of the micromechanical analysis and the steady-state cracking theory considering the fracture characteristics of matrix and the interfacial properties between fibers and matrix. Then 4 mixture proportions were determined according to the type and amount of fibers and the experiment was performed to evaluate the mechanical performance of those. The HFSLCC showed 3% of tensile strain, 4.2MPa of ultimate tensile stress, 57MPa of compressive strength and $1,660kg/m^3$ of bulk density. The mechanical performance of HFSLCC incorporated with PVA fibers of 1.0 Vol.% and PE fibers of 0.5 Vol.% is similar to those of the HFSLCC incorporated with fibers of 2.0 Vol.%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.217-222
• /
• 2015

There has been increased amount of atmospheric pollutants including NOx and SOx which cause acid rain and photochemical smog as a result of increased use of fossil fuels. In order to reduce the amount of pollutants produced by fossil fuel, wet scrubber system is introduced in this experiment. Wet scrubber system is applied to a diesel engine (3,298 cc) and the amount of smoke is measured before and after the application in terms of aspect ratio, filling rate, and flow rate. The result showed a lot of smoke reduction when wet scrubber system was applied, and also the aspect ratios and water spray flow rate were the important factors to improve smoke reduction.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.4
• /
• pp.41-48
• /
• 1999

Silica is the most popular materials as a filler of EMC for microelectronic packaging. However, because of its low thermal conductivity, the use of silica is restricted to parts requiring high thermal dissipation. The superior fluidity of EMC can be achieved with a combination of filler size distribution. In this study, physical properties of EMC filled with the crystalline silica(13$\mu\textrm{m}$) which have high fluidity and low cost and the AlN(2 $\mu\textrm{m}$) which have high thermal conductivity and low coefficient of thermal expansion were evaluated by changing the AlN/silica ratios. As a result of the evaluation of physical properties of EMC, the optimum mixing ratio of AlN/crystalline silica was 0.3/0.7. In this condition, binary mixture(AlN/crystalline silica) filled EMC showed superior properties, i.e., in the thermal conductivity, CTE, dielectric constant, flexural strength, and thermal shock resistance without reduction of fluidity.