• Journal of the Korean Vacuum Society
• /
• v.14 no.1
• /
• pp.35-39
• /
• 2005

In the UV-NIL process using an elementwise patterned stamp (EPS), which includes channels formed to separate each element with patterns, low-viscosity resin droplets with a nano-liter volume are dispensed on all elements of the EPS. Following pressing of the EPS, the EPS is illuminated with UV-light to cure the resin; and then the EPS is separated from several thin patterned elements on a wafer. Experiments on UV-NIL were performed on an EVG620-NIL. 50 - 100nm features of the EPS with 3m channels were successfully transferred to 4 in. wafers. Especially, the wafer deformation during imprint was analyzed using the finite element method (FEM) in order to study the effect of the wafer deformation on the UV-NIL using EPS.

• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.122-131
• /
• 1997

Zinc titanate sorbents for $H_2S$ removal were prepared and their reactivities were studied for high temperature desulfurization of coal gas. Sulfidation of zinc titanates by $H_2S$ sorption was conducted in a packed-bed tubular flow reactor at the temperature range of $550{\sim}750^{\circ}C$, and the results reveal that $650^{\circ}C$ was the optimal sulfidation temperature with respect to desulfurization efficiency and zinc loss. The structural change of sorbent particle was investigated by SEM analysis for the forbents sulfided at $650^{\circ}C$ and subsequently regenerated at $750^{\circ}C$. The stability of desulfurization capability as well as the mechanical stability of the zinc titanates was studied by means of the successive cycles of sulfidation-regeneration of sorbents, and the sorbent samples taken after the 10th cycle were characterized using BET, XRD, and SEM/EDX analyses. Zinc titanate sorbents exhibited nearly constant desulfurization capability in the successive cycle operation.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.3
• /
• pp.35-39
• /
• 2015

Continuous adsorption and recovery characteristics for gold and lead-cyanide complexes in industrial wastewater were investigated by the Dowex 21K XLT resin. The Dowex 21K XLT resin could continuously remove over 95% for gold-cyanide complex until 520 bed volumes at the 0.5 mL/min of influent flow rate, however, could not remove lead-cyanide complex at all. The 96% of gold-cyanide complex adsorbed onto Dowex 21K XLT resin could be recovered by mixed solvent with HCl and acetone (7:3 ratio) within 8 bed volumes. Also, the bed volume for gold-cyanide complex using secondly reused Dowex 21K XLT resin was maintained as the 490, therefore, continuous process using Dowex 21K XLT resin can be sufficiently applied to the industrial wastewater containing gold ions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.25-37
• /
• 2005

For pump-fed rocket propulsion system, the temperature of LOX to be supplied to turbopump inlet should be satisfied with pump inlet temperature requirement during all operating stages, as excessive temperatures can result in cavitation due to reduction in NPSH, thus either damaging the pump or adversely affecting pump performance rise. So exact estimation of LOX temperature rise is absolutely needed for developing reliable propulsion system. This paper presents systematic analysis scheme for estimating inner process of cryogenic propellant tank which is needed for LOX temperature rise. And this paper presents LOX temperature rise and thermal stratification for all rocket operating stages including cooling, filling, waiting, pre-pressurization and firing, with the application of buoyancy driven boundary layer theory.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.822-827
• /
• 1999

The specific capacitance characteristics which were of the electric double layer capacitors(ELDC) made of phenol based activated carbon fiber(ACF) electrodes and organic electrolytes has been investigated with respect to different specific surface area of electrodes and different kinds of organic electrolytes. Throughout charge-discharge cell tests, it has been found that larger surface area and larger pore diameter of electrodes contribute to increase the specific capacitance. Binary mixture of organic solvent with propylene cabonate(PC) and tetrahydrofuran(THF) for 1 M-$LiClO_4$ electrolyte has a higher specific capacitance than single solvent of PC or mixed solvent with PC and diethyl cabonate(DEC). Also, even though 1 M-tetraethylamonium perchlorate(TEAPC) of organic electrolyte shows higher specific capacitance, it has longer charge time because of its lower ion mobility.

• Korean Chemical Engineering Research
• /
• v.45 no.6
• /
• pp.582-590
• /
• 2007

In view of the analysis of the phenomena and the prediction of the performance, mathematical modelling and simulation of a high temperature pilot reactor for water gas shift reaction (WGSR) has been carried out. Multiscale simulation incorporated computational fluid dynamics (CFD) technique, which has the capability to deal with the reactor shape, fluid and energy transport with extensive degree of accuracy, and process modeling technique, which, in turn is responsible for reaction kinetics and mass transport. This research employed multiscale simulation and the results were compared with those from process simulation. From multiscale simulation, the maximum conversion of was predicted approximately 0.85 and the maximum temperature at the reactor was calculated 720 K, resulting from the heat of reaction. Dynamic simulation was also performed for the time transient profile of temperature, conversion, etc. Considering the results, it is concluded that multiscale simulation is a safe and accurate technique to predict reactor behaviors, and consequently will be available for the design of commercial size chemical reactors as well as other commercial unit operations.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.2
• /
• pp.137-144
• /
• 2020

In this study, we propose a new truss deckplate system, which does not require temporary floor supports during construction, with ultra-high-performance concrete (UHPC) infilled top bars. The increased stiffness and strength of the proposed system were well retained as compared to those of the existing truss deckplate systems, thereby resulting in the reduction of maximum deflection at the span center. Four-point bending tests were performed on five specimens with a net span of 4.6 m to evaluate the structural performance of proposed system in the construction stage. In addition, the load-deflection curve was plotted for each specimen, and the effects of test parameters were analyzed. Further, a rigorous nonlinear three-dimensional finite element analysis was performed, and its results were compared with the test results. From the results, it was observed that the test specimens of the proposed system exhibited superior performance as compared to those of the existing one and also satisfied the serviceability requirement during construction provided by the Korea Building Code 2016.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.4 s.77
• /
• pp.481-490
• /
• 2005

This paper summarizes the full-scale test results on the CFT column-to-flat plate connections subjected to gravity loading. CFT construction has gained wide acceptance in a relatively short time in domestic building construction practice due to its various structural and construction advantages. Constructing an underground parking floor as a flat plate system is often regarded as essential for both cost savings and rapid construction. Efficient details for CFT-column-to-flat-plate connections have not been proposed yet, however, and their development is urgently needed. Based on some strategies that maximize economical field construction, several connecting schemes were proposed and tested based on a full-scale model. The test results showed that the proposed connection details can exhibit punching shear strength and connection stiffness comparable to or greater than those of their R/C flat plate counterpart.

• Journal of Korea Water Resources Association
• /
• v.35 no.3
• /
• pp.295-306
• /
• 2002

The modified TOPMODEL of two storage systems has been integrated to the generalized assumptions of decreasing hydraulic conductivity to vertical direction. Three different recharge functions were introduced to explore the impact of the macropore flow to vortical direction, the storage at the surface zone and the relative storage deficit of the soil matrix. Combinations of these approaches provide 30 type of the model structure for the hillslope hydrology. Developed models have been applied to several hydrologic events at the Sulmachun watershed. The performance evaluation with the Monte carlo simulation suggests that the exponential function of transmissivity reduction should be appropriate form for the physically -based hydrologic simulation on the Sulmachun watershed. It has been shown that the recharge function of macropore flow contributes to improve the predictability of the generalized version of modified TOPMODEL.

• Resources Recycling
• /
• v.9 no.6
• /
• pp.15-22
• /
• 2000

There are many intensive efforts to develop the recycling technologies of waste plastics in steel works to tackle the saving of resources and the protection of the natural environment. In this study, the thermogravimetric analyses for three kinds of plastics, the combustion experiments and the theoretical approach for calculating the flame temperature in the blast furnace had been performed to understand the behavior of plastics in the raceway. The thermal decompositions of plastics were studied using thermogravimetric analyzer under the atmospheric condition. The starting temperature of thermal decomposition and the maximum weight loss point were increased in proportion to the logarithmic values of heating rate. The combustion characteristics of plastics were simulated in a coke-bed combustor. The combustion efficiency of plastics was lower than that of pulverized coal. The oxygen enrichment was found out to be one of the useful methods to increase the combustibility of plastics in raceway. The maximum injection rate of plastics was calculated based on the flame temperature.