• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.992-995
• /
• 2001

고전압 펄스파워를 이용한 장치들이 환경설비 및 군용기술 등 여러 분야에서 적용되고 있다. 이들 장치는 고전압전원장치가 필수적이다. 고전압 전원 장치는 소형이면서 높은 반복 율로 재충전이 가능하고 안정성 있는 운전이 요구되어진다. 개발된 전원장치는 펄스발생기의 에너지 저장 캐패시터를 50 kV까지 층전할 수 있고 다수의 병렬운전이 가능한 정전류 전원장치이다. 본 전원장치는 200 nF 캐패시터를 6.48 ms이내에 50 kV까지 충전할 수 있도록 설계되어있다. 본 논문에서는 직렬공진에 의해 35 kW, 50 kV의 고전압을 만드는 전원장치의 동작시험에 대한 결과를 보이고자 한다.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1997.10a
• /
• pp.71-72
• /
• 1997

1. 서론 : 공기중의 산소분리용 고분자막은 높은 선택도를 동시에 요구한다. 이 두가지 조건을 만족시키는 소재 개발과 기존의 고분자물질을 수식하는 연구가 진행되고 있다. 고분자막에 대한 수식방법으로는 UV처리, plasma처리등이 있으나, 이들 방법은 선택도는 증가시키나 투과도를 감소시키는 경향이 있다. 기체의 투과저항을 줄이기 위하여 다공성 지지체 위에 박막을 입힌 복합막과 박막의 skin layer와 sub-layer를 갖는 비대칭막은 투과저항을 줄일수 있으나 선택도는 고분자 고유의 80%정도까지 감소되는 것으로 알려졌다. 본 연구의 목적은 고분자 복합막의 투과분리특성을 향상시키기 위한 것으로 지지층의 세공과 표면에 실리카/고분자를 충전, 피복시켜 투과분리특성을 조사하였다. 현재까지의 연구는 낮은 투과계수와 높은 선택도를 갖는 고분자물질이 사용되었으나, 본 연구에서는 폴리이미드로는 폴리이미드 중에서 투과계수가 가장 높다고 알려진 6FDA-p-TeMPD[{(3,3',4,4'-dicarboxyphenyl)hexafluoropropanedianhydride}-{2,3,5,6-Tetra-methyl-1,4-phenylenediamine}] 폴리이미드를 택하였으며 다공성지지체는 aluminum oxide를 사용하였다 . 본 실험에서는 선택도와 투과속도에 주로 영향을 미치는 폴리이미드와 실리카의 양에 대하여 고찰하였다.

• Journal of Environmental Science International
• /
• v.23 no.6
• /
• pp.1143-1149
• /
• 2014

The adsorption experiments of lithium ions were conducted in the fixed bed column packed with activated carbon modified with nitric acid. Effect of inlet concentration, bed hight and flow rate on the removal of lithium ions was investigated. The experimental results showed that the removal and the adsorption capacity of lithium ions increased with increasing inlet concentration, and decreased with increasing flow rate. When the bed height increased, the removal and the adsorption capacity increased. The breakthrough curves gave a good fit to Bohart-Adams model. Adsorption capacity and breakthrough time calculated from Bohart-Adams model, these results were remarkably consistent with the experimental values. The adsorption capacity was not changed in the case of 3 times repetitive use of adsorbent.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.49-50
• /
• 2006

This study experimented to observe an influence of experimental conditions on production characteristics of slurry ice by putting ball into test section to disturb ice adhesion. And at this experiment it used ethylene glycol-water solution and the concentration is 20wt%. The experimental apparatus was constructed of ethylene glycol-water solution and slurry ice storage tank, brine tank. pumps for ethylene glycol-water solution and brine circulating, a mass flow-meter, data logger for fluid temperature measuring and a vertical circular tube with two copper tubes as test section. The experiments were carried out under various conditions, with mean velocity of fluid at the entry ranging from 0.07 to 0.13m/s and ball diameter is 10mm, 15mm. Also ball filling rate is 33%, 50%.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.2
• /
• pp.64-72
• /
• 2001

Weld line is one of serious troubles which are observed in a plastic part manufactured by a injection molding process. This is caused by many process factors, which are molding pressure, temperature, velocity, location of a injection gate, mold geometry and material properties. investigation on the effects of these process factors to the appearance of a weld line was carried out using a finite element method. Filling and packing analyses were carried out by modifying both the configuration of the injection gates and cavity thickness. Proper locations of the injection gates could be determined by considering molding pressure, temperature, velocity and frozen layer, and whereby the weld line was controled. In order to make a weak appearance of the weld line, flow velocity and flow front in a cavity were also investigated by modifying a cavity thickness. As a result, flow front was extended around the corner in the cavity by changing the flow velocity and hence the appearance of the weld line was much weakened.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.265-271
• /
• 1998

High temperature wear behavior of plasma sprayed zirconia based coating sealing with zirconia sol were investigated for high temperature wear resistance application. The zirconia powders containing 2.5, 5.0, 7.5, 10.0 mol% of MoS$_2$, $Fe_2O_3$ for plasma spray were made by spray drying method. As-sprayed coating was sealed by zirconia-sol to fill up the pore and crack in coating. wear test were performed at temperature ranges from room temperature to 600$\circ$C. The microstructural changes of before and after sealing process were examined by SEM, XRD and EPMA. After sealing process, the porosity was decreased and micro-hardness was increased. The wear properties of coating after sealing process were improved by sealing of pores and cracks. The behavior of wear amount and coefficient of friction were same tendency to before sealing process.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2001.11a
• /
• pp.362-363
• /
• 2001

VOCs의 위해성은 광화학 스모그의 원인 물질이며 발암성 유해물질, 지구 온난화와 성층권오존층의 파괴 물질 및 대기중 악취 물질로서 국민 건강 및 환경에 악 영향을 초래하여 세계적으로 VOCs관리를 대기질 관리의 주요 정책 수단으로 이용하는 국가가 증가하는 추세이다. 그러나 국내의 현행 대기질 관리 정책은 대기중에 광범위하게 분포하고 있는 몇 가지의 환경기준물질 관리에만 중전을 두고있는 실정이면, 또한 VOCs 처리 기술로 적용 가능한 기존의 소자, 흡착, 흡수와 같은 기술의 경우, 폭발성 화합물 처리 시 발생하는 위험성이나, 2차 오염물 생성 등 문제점이 발생할 수 있고, 또한 초기 설치비나 운전비용 등에 의해 적용하기가 힘든 경우도 발생할 수 있다. (중략)

• Journal of Astronomy and Space Sciences
• /
• v.11 no.1
• /
• pp.71-80
• /
• 1994

It is generally known that the measurement of the ionospheric total electron content(TEC) by GPS can more accurately monitor the broader area of the ionosphere than other current methods. \Ve measured the TEC along a slant path considering the arrival time differences of P-code which is transmitted from GPS satellites with the modulation on two L-band carrier frequencies, L1 (1574.42MHz) and L2 (1227.60MHz). Under the assumptions that the ionosphere is uniformly distributed and its average height is 350km, we transformed the slant TEC to the vertical TEC at the point that the line-of-sight direction to GPS satellite cut across the average height of the ionosphere. Because there is no dual frequency P-code GPS receiver in Korea, we used the data observed at the TAIW GPS station ($N25^{\circ},E121.5^{\circ}$) in Taiwan which is one of the core stations in International GPS and Geodynamics Services (IGS). The TEC values obtained in this work showed a typical daily variation of the ionosphere which is high in the daytime and low in the nighttime. Our results are found to be consistent with the SOLAR-DAILY data of NOAA and the Klobuchar's model for the ionospheric correction of GPS. In addition, in the cornparision with SOLAR-DAILY data, we estimated the precision of our TEC measurement as 2 TEC.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.375-381
• /
• 2010

In this paper, the heat-transfer characteristics of steam reforming in an annular reactor are presented. Heat is supplied by the catalytic combustion of syn-gas. The thermal behaviors of exothermic and endothermic reactions in a directly coupled concentric-tube packed-bed reactor were investigated experimentally. The gas mixture supplied for catalytic combustion consisted of the off-gas emitted from MCFC anode. Methane in steam at a suitable S/C (steam-to-carbon) ratio was used in the reforming reactions. On the basis of the experimental results, a simple simulation was performed to predict the temperature profile required in the reforming side of the reactor to achieve optimum hydrogen yield. The results of this study may be utilized as reference data in future studies for further development of coupled reactors.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.8
• /
• pp.1172-1182
• /
• 2002

In the present study a general criterion for local thermal equilibrium is presented in terms of parameters of engineering importance which include the Darcy number, the effective Prandtl number of fluid, and the Reynolds number. For this, an order of magnitude analysis is performed for the case when the effect of convection heat transfer is dominant in a porous structure. The criterion proposed in this study is more general than the previous criterion suggested by Carbonell and Whitaker, because the latter is applicable only when conduction is the dominant heat transfer mode in a porous medium while the former can be applied even when convection heat transfer prevails. In order to check the validity of the proposed criterion for local thermal equilibrium, the forced convection phenomena in a porous medium with a microchanneled structure subject to an impinging jet are studied using a similarity transformation. The proposed criterion is also validated with the existing experimental and numerical results for convection heat transfer in various porous materials that include some of the parameters used in the criterion such as a microchannel heat sink with a parallel flow, a packed bed, a cellular ceramic, and a sintered metal. It is shown that the criterion presented in this work well-predicts the validity of the assumption of local thermal equilibrium in a porous medium.