• 한국분무공학회지
• /
• 제9권1호
• /
• pp.37-42
• /
• 2004

In a port fuel injection system of engine, a large part of fuel injected into an intake port adheres on its wall and inlet valve. Consequently, the wall impinging spray interaction might occur the generation of several harmful phenomena. There are uncontrollable mixture formation, an accidental backfire and unburned hydrocarbons. Therefore, it is important to analyze the fuel behavior during the spray-wall interaction. In this study, splash characteristics of impingement and reflecting or scattering behavior of droplets of fuel injected from EFI nozzle were studied experimentally. A test fuel used is LAWS and its physical characteristics are similar to the conventional gasoline except for the ignition point. Since the liquid film formed immediately after impinging on an impingement plate is unstable, it is easy to cause secondary disintegration. In addition, when the intermittently impingement on the impingement plate with LAWS, the splash ratio is around 0.6. If an injection period becomes longer, liquid film will become thick and the splash ratio will fall bout 10 percent. On the other hand, when the injection period of an intermittent spray is long, the same time lapse as a continuous spray is shown.

• 한국분무공학회지
• /
• 제24권4호
• /
• pp.185-193
• /
• 2019

The effervescent atomizer is one of twin-fluid atomizers that aeration gas enters into bulk liquid and two-phase flow is formed in the mixing section. The effervescent atomizer requires low injection pressure and small amount of aeration gas, as compared to other twin-fluid atomizers. In this study, cold flow test was conducted to investigate the spray characteristics of aerated impinging jets. The present effervescent impinging atomizers were composed of the aerator device and like-on-like doublet impinging atomizer which had different impinging angles. To analyze the spray characteristics such as breakup length and droplet size distribution, the image processing technique was adopted by using instantaneous images at each flow condition. Non-dimensional parameters, induced by the homogeneous flow model, were used to predict the breakup length. The breakup length was decreased with the mixture Reynolds number and impinging angle increasing. The result of droplets showed that the size distribution was axisymmetric about the center of the injector and their diameter tended to decrease with increasing GLR.

• 대한기계학회논문집B
• /
• 제25권5호
• /
• pp.627-633
• /
• 2001

Characteristics of a diesel spray impingement with the variation of ambient temperature, wall temperature and ambient pressure were investigated through shadowgraphy method by using high speed camera. The radial penetration of spray was increased with ambient temperature and wall temperature. It is resulted from the decrease of ambient gas density caused by the increase of temperature. The height of spray was also increased with ambient temperature and wall temperature, because the height of stagnate region is noticeably increased, although height of wall jet vortex is decreased. At the same ambient pressure, the area ratio of impinging spray of room temperature environment to high temperature environment was increased, as the temperature difference between room temperature and high temperature increases. And the increment of area ratio was higher at low ambient pressure than high ambient pressure.

• 한국융합학회논문지
• /
• 제12권1호
• /
• pp.185-191
• /
• 2021

과립 분말 야금법은 기존 분말 야금법보다 치밀도가 높은 소결 부품을 얻을 수 있는 제조 기술이다. 하지만 추가 과립화 공정에 따른 생산 비용 증가가 상당하다는 단점이 있다. 과립 분말 야금법의 생산성 향상을 위해서는 과립 분말 제조 시 높은 회수율이 보장되어야 한다. 본 논문에서는 분체 동역학 전산 해석법인 이산요소법을 이용하여 과립 분말의 수율에 영향을 미치는 과립화 공정의 특성에 대해 살펴보았다. 분무 과립 공정 중 과립화 분말의 비산, 충돌 및 소착 현상을 시뮬레이션함으로써 분무 건조기의 운전 조건에 따른 과립화 분말의 파손 및 회수 가능 여부를 예측하였다. 본 논문의 가상 공정 시뮬레이션 융합 연구 결과는 실제 금속 분말의 분무 과립화 공정의 생산성 향상에 이바지할 것으로 기대한다.

• 한국항공운항학회지
• /
• 제15권4호
• /
• pp.1-8
• /
• 2007

Spray characteristics of a unlike triplet injector were investigated experimentally. Spray images and SMD of droplet were measured to evaluate the spray characteristics injected by liquid/gas combinations. G-L-G(Gas-Liquid-Gas), L-G-L(Liquid-Gas-Liquid) type of injector were used by changing the gas and liquid feed lines. The SMD graph shows that the droplet sizes decrease in the out of radial direction at a fixed gas Reynolds number. The SMD value of decreasing tendency shows that the more ethyl alcohol ratio increase, the more SMD value decrease.

• 한국추진공학회지
• /
• 제2권2호
• /
• pp.24-29
• /
• 1998

Duplex Type의 2-유체 공기충돌형 Swirl 인젝터의 분무특성을 파악하고자 유체공급압력 0~13kg/$\textrm{cm}^2$ 범위에서 유량계수, 등가 분산각, 질량분포를 실험적으로 구하였다. 일반적으로 기체의 총 유량이 증가할수록 미립화는 촉진되나 반경방향 유량이 많은 경우에 분무형상은 비교적 안정적이었으며, 축방향 보다는 반경방향 선회기가 미립화에 미치는 영향이 컸다. 3kg/$\textrm{cm}^2$을 제외하고는 물 유량이 증가함에 따른 등가 분산각의 변화는 미소하였고, 기체의 유량증가도 마찬가지였다. Patternator를 사용한 질량 분포는 반경방향 기체유량이 증가함에 따라 분포곡선의 최대점은 낮아지면서 더 넓은 영역에 걸쳐 분포하였고, 물 유량의 증가에 따른 질량중심점의 위치는 변화가 없었다.

• 한국분무공학회지
• /
• 제23권1호
• /
• pp.30-35
• /
• 2018

The objective of this study is to predict numerically the effect of intake humidification on the injected diesel fuel spray characteristics in a compression ignition engine. In this work, Wave model and Ducowicz model were applied as the break-up model and evaporation model, respectively. The amount of water vapor for the humidification was changed from 0% to 30% of injected fuel mass. The number of applied meshes was generated from 49,000 to 110,000. At the same time, the results of this work were compared in terms of spray tip penetration, SMD and equivalence ratio distributions. It was found that the cylinder temperature and cylinder pressure were decreased with increasing water vapor mass by vaporization latent heat and specific heat, however, the difference was very small. So, the spray tip penetration was not different by water vapor mass. Also, higher equivalence ratio distributions were observed with increasing water vapor mass by the improvement of fuel atomization.

• 한국분무공학회지
• /
• 제16권3호
• /
• pp.140-145
• /
• 2011

Gelled propellants are non-Newtonian fluids in which the viscosity is a function of the shear rate, and they have a high dynamic shear viscosity which depends on the amount of gelling agent contents. The present study has focused on the breakup process, wave development of ligament and liquid sheets formed by impinging jets with various gelling agent contents. The breakup process of like-on-like doublet impinging jets are experimentally characterized using non-Newtonian liquids. The spray shape with elliptical pattern is distributed in a perpendicular direction to the momentum vectors of the jets. Gelled propellant simulants with high viscosity jets are more stable and produce less pronounced surface waves than low viscosity jets. Gelled propellant simulants from like-on-like doublet impinging jets have the spray shape of closed rim patterns at low pressure. As the injection pressure increased, rimless patterns which were composed of ligament sheets and small droplets emerged due to the effect of the aerodynamic action.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.528-533
• /
• 2001

An experimental study is carried out to investigate the effects of air and water mass flow rates on cooling characteristics of mist impinging jet on a flat plate. Experiments are conducted with air mass flow rates from 0.0 to 3.0 g/s, and water mass flow rates from 5.0 to 20.0 g/s. An air-atomizing nozzle is used for the purpose of controlling air and water mass flow rates. In this study, a new test section is designed to obtain local heat transfer coefficient distributions. Heat transfer characteristics of the mist impinging jet are explained with the aid of flow visualization. Surface temperature and heat transfer coefficient distributions become more uniform as air mass flow rate increases, and that the increases in water flow rate mainly enhance cooling performance. Air mass flow rate weakly influences averaged heat transfer coefficient when water mass flow rate is low, but averaged heat transfer coefficient increases remarkably as air mass flow rate in case of high water mass flow rate.

• 대한기계학회논문집B
• /
• 제27권4호
• /
• pp.511-517
• /
• 2003

An experiment is conducted to investigate the effect of air and water mass flow rates on cooling characteristics of mist impinging jet on a flat plate. The air mass flow rate ranges from 0.0 to 3.0 g/s, and water mass flow rates from 5.0 to 20.0 g/s. An air-atomizing nozzle is used fur the purpose of controlling air and water mass flow rates. The test section is designed distinctively from previous works to obtain local heat transfer coefficient distributions. Heat transfer characteristics of the mist impinging jet are explained with the aid of flow visualization. Surface temperature and heat transfer coefficient distributions become more uniform as air mass flow rate increases. The water flow rate provides substantial contribution to enhancement of cooling performance. On the other hand, The air mass flow rate weakly influences the averaged heat transfer rate when the water mass flow rate is low, but the averaged heat transfer rate Increases remarkably with the air mass flow rate in case of the high water mass flow rate.