• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.9
• /
• pp.883-891
• /
• 2013

In wireless smart phone charging scenario, the transmitter pad is larger than the size of the receiver pad. Thus, it is important to supply a constant power to the receiver regardless of its location. In this paper, we propose a new method to regulate the receiver's power by adjusting a drain bias of class E power amplifier. The proposed LF-band wireless power transfer system is as follows: a buck converter power supply which is controlled by a pulse width modulation(PWM) IC TL494, a class E amplifier using a low cost IRF510 power MOSFET, a transmitter coil whose dimension is $16cm{\times}18cm$, a receiver coil whose dimension is $6cm{\times}8cm$, and a full bridge rectifier using Schottky diodes. A measured performance show a maximum output power of 4 W and system efficiency of 67 % if we fix the bias voltage. If we adjust the bias voltage, the received power can be maintained at a constant power of 2 W regardless of receiver pad location.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.6
• /
• pp.117-125
• /
• 2007

Recently, a fuel cell with low voltage and high current output characteristics is remarkable for new generation system. It needs both a DC-DC step-up converter and DC-AC inverter to be used in fuel cell generation system. Therefor, this paper, consists of an isolated DC-DC converter to boost the fuel cell voltage 380[VDC] and a PWM inverter with LC filter to convent the DC voltage to single-phase 220[VAC]. Expressly, The fuel cell system which it proposes DC-DC the efficient converter used PWM the phase transient control law and it depended to portion resonance ZVS switching, loss peek voltage and electric current of realization under make schedule, switching frequency anger and the switch reduction. And mind benevolence it sprouted 2 in stop circuit and it added and a direct current voltage and the electric current where the ingredient is reduced in load side ripple stable under make whom it will be able to supply. Besides the efficiency of 92[%]is obtained over the wide output voltage regulation ranges and load variations. Also, under make over together the result leads simulation and test, the propriety confirmation.

• Journal of Navigation and Port Research
• /
• v.27 no.2
• /
• pp.209-215
• /
• 2003

In this paper. We tested and fabricated the error amplifier for the 15 Watt linear power amplifier for the IMT-2000 baseband station. The error amplifier was comprised of subtractor for detecting intermodulation distortion, variable attenuator for control amplitude, variable phase shifter for control phase, low power amplifier and high power amplifier. This component was designed on the RO4350 substrate and integrated the aluminum case with active biasing circuit. For suppression of spurious, the through capacitance was used. The characteristics of error amplifier measured up to 45 dB gain, $\pm$0.66 dB gain flatness and -15 dB input return loss. Results of application to the 15 Watt feedforward Linear Power Amplifier, the error amplifier improved with 27 dB cancellation from 34 dBc to 61 dBc IM$_3$.

• The Transactions of the Korea Information Processing Society
• /
• v.1 no.1
• /
• pp.114-128
• /
• 1994

It is very difficult for a nonprofessional programmer in Koera to write a program with very High Level Language such as, V,REFINE, GIST, and SETL, because the semantic primitives of these languages are based on predicate calculus, set, mapping, or testricted natural language. And it takes time to be familiar with these language. In this paper, we suggest a method to reduce such difficulties by programming with the declarative, procedural constructs, and aggregate constructs. And we design and implement an experimental knowledge-based automatic programming system. called HAPS(Hangul Automatic Program System). HAPS, whose input is specification such as Hangul abstract algorithm and datatype or Hangul procedural constructs, and whose output is C program. The method of operation is based on rule-based and program transformation technique, and the problem transformation technique. The problem area is general problem. The control structure of HAPS accepts the program specification, transforms this specification according to the proper rule in the rule-base, and stores the transformed program specification on the global data base. HAPS repeats these procedures until the target C program is fully constructed.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.14 no.2
• /
• pp.96-108
• /
• 2011

Going abreast of high public concerns on the environment, the need of environmental modeling has been increased to assess the impact of space exploitation of environment. GIS offers potential solutions to the many problems encountered during water-quality modeling. But there are also many problems associated with the modeling. The preparation of necessary parameters for the modeling can be complicated. Also, the results from one model can be different from each other even the same area is analyzed. This paper aims to develop the data processing system to couple the Qual2E and HyGIS in which Qual2E input and output data files can be created, modified and processed using HyGIS and assess the performance of the system. A structural analysis and standardization of modeling are conducted to identify data flow and processing of Qual2E. Algorithms of the defined processors are designed and developed as component modules. The data model of HyGIS-Qual2E is designed, and GUI(Graphical User Interface) is developed using Visual Basic 6.0 and GDK.

• Journal of Auto-vehicle Safety Association
• /
• v.7 no.3
• /
• pp.7-13
• /
• 2015

Occupant protection performance in frontal crashes has been developed and assessed for mainly front seat occupants over many years, and in recent years protection of rear seat occupants has also been extensively discussed. Unlike the front seats, the rear seats are often occupied by children seated in rear-facing or forward - facing child restraint systems, or booster seats. In the ENCAP, child occupant protection assessments using 18-month-old(P1.5) and 3-year-old(P3) test dummies in the rear seat have already been changed to new type of 18-month-old (Q1.5)and 3-year-old(Q3) test dummies. In addition, ENCAP are scheduled with the development and introduction of test dummies of 6-year-old (Q6) and 10.5-year-old children(Q10) starting 2016. In KNCAP, Q6 and Q10 child dummies will be introduced in 2017 as well. Automobile manufacturers need to develop safety performance for new child dummies closely. In this paper, we focused on Q6 and Q10 child dummies sitting in child restraint system. Offset frontal crash tests were conducted using two types of test dummies, Q6 and Q10 child dummies, positioned in the rear seat. Q6 and Q10 were used to compare dummy kinematics in rear seating positions between Q6 behind the driver's seat and Q10 behind the front passenger's seat. The full vehicle sled test results of both dummies were conducted with different restraint systems. It showed that several injury and image data was collected as the result of the full vehicle sled test. Based on the results of these investigations, this paper describes which factor is most important and combination is the best performance when evaluating rear seat occupant protection for Q6 and Q10 child dummies.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.96-96
• /
• 1999

CdTe는 일반적으로 광전 소자나 Xtjs 및 λ선 감지 소자로서 많은 연구가 되어지고 있는 물질이다. 특히 적외선 감지 소자로 쓰이고 있는 HgCdTe 물질의 기판으로서도 많은 연구가 진행되고 있다. 이러한 여러 가지 목적으로 사용함에 있어서 CdTe 내에 가지고 있는 여러 가지 불순물에 의한 영향으로 각종 결함밴드들이 형성됨으로서 소자로서의 응용에 많은 지장을 주고 있다. 이러한 이유로 여러 가지 방법으로 불순물 및 결합에 의한 준위에 관한 연구들이 진행되고 있다. 본 실험에서는 MBE 법으로 성장된 In 도핑된 CdTe 박막의 광학적 성질을 관찰하기 위하여 수소화 및 열처리를 하여 PL 법을 이용하여 관찰하여 보앗다. 열처리는 Cd 분위기의 50$0^{\circ}C$에서 5시간 동안 수행하였으며 수소화는 rf plasma 장치를 이용하여 8$0^{\circ}C$에서 50mW/c2의 출력으로 1시간동안 수행하여 주었다. 열처리한 시료의 경우 PL 신호는 갓 성장한 시료와 비교하여 깊은 준위에 관련된 신호들만 변화가 있었을뿐 그리 큰 변화가 있지는 않았다. 그러나 수소화시킨 시료의 경우 전체적으로 피크의 크기가 5배정도 감소하는 것을 볼 수 있었는데 이것은 수소에 의하여 passivation된 효과로 볼 수 있다. 정량적인 passivation 효과를 보기 위하여 온도의존성 PL 측정을 하여 보았다. 측정에서 관측된 (D,h) emission lines의 FWHM을 비교하여 본 결과 FWHM 온도가 증가함에 따라 선형적으로 증가하는 것이 아니라 급격한 증가를 q이는 구간을 관착할 수 있었다. 이것은 CdTe내에 존재하는 전하를 띠고 있는 주게와 받게의 결합의 결과로 나타나는 현상으로 보여진다. 이러한 결과를 통하여 얕은 준위에 있는 주게 불순물의 농도를 계산해 보았고 Hall 측정을 얻은 결과와 비교하여 보았다.판단된다. 따라서 이 기술은 기존의 광소자 제작을 위한 IFVD 방법의 문제점을 해결할 뿐만 아니라 결정 재성장 없이 도일한 기판상에 국부적으로 상이한 bandgap 영역을 만들 수 있기 때문에 광소자 제작에 적극 이용될 수 있다.나지 않았으며 BST 박막에서는 약 1.2V의 C-V이력현상이 보였다.를 이용하였으며, 이온주입후 열처리 온도에 따른 활성화 정도의 관찰을 위하여 4-point probe와 Hall measurement를 이용하였다. 증착된 다결정 SiGe의 두게를 nanospec과 SEM으로 분석한 결과 Gem이 함량이 적을 때는 높은 온도에서의 증착이 더 빠른 증착속도를 나타내었지만, Ge의 함량이 30% 되었을 때는 온도에 관계없이 일정한 것으로 나타났다. XRD 분석을 한 결과 Peak의 위치가 순수한 Si과 순수한 Ge 사이에 존재하는 것으로 나타났으며, ge 함량이 많아짐에 따라 순수한 Ge쪽으로 옮겨가는 경향을 보였다. SEM, ASFM으로 증착한 다결정 SiGe의 morphology 관찰결과 Ge 함량이 높은 박막의 입계가 다결정 Si의 입계에 비해 훨씬 큰 것으로 나타났으며 근 값도 증가하는 것으로 나타났다. 포유동물 세포에 유전자 발현벡터로써 사용할 수 있음으로 post-genomics시대에 다양한 종류의 단백질 기능연구에 맡은 도움이 되리라 기대한다.다양한 기능을 가진 신소재 제조에 있다. 또한 경제적인 측면에서도 고부가 가치의 제품 개발에 따른 새로운 수요 창출과 수익률 향상, 기존의 기능성 안료를 나노(nano)화하여 나노 입자를 제조, 기존의 기능성 안료에 대한 비용 절감 효과등을 유도 할 수 있다. 역시 기술적인 측면에서도 특수소재 개발에 있어 최적의 나노 입자 제어기술 개발 및 나노입자를 기능성 소재로 사용하여 새로운 제품의 제조와 고압 기상 분사기술의 최적화에 의한 기능성 나노 입자 제조 기술을 확립하고 2차 오염 발생원인 유

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.73-80
• /
• 2004

In this paper, the implementation and embedding method of the existing air-filled waveguide-filters at millimeter-wave on general PCB substrate is introduced by systematically inserting the vias inside waveguide and mathematically manipulating the simple equations obtained ken the classical circular-post waveguide filter design. All the metal structures placed vertically such as side wall fur perfect ground plane and circular-post for signal control in the air-filled WR-22 waveguide are replaced with several types of via for constructing the bandpass-filter. Side wall and poles inside waveguide are realized by placing a series array of via and tuning the via diameter. The lengths of x, y, z axis are reduced in proportion to root square of employed substrate dielectric constant and especially the length of z axis can be more reduced due to the characteristics of the wave propagation. Because the mass production on PCB is possible without fabricating a large-scaled metal waveguide of WR-22 as input/output ports at millimeter-wave regime, the manufacturing cost is reduced considerably. Finally, when using multilayer process like LTCC for small-sized module, it is one of advantages to use only one layer f3r the filter fabrication. To evaluate the validity of this novel technique, order-3 Chebyshev BPF(Bandpass-Filter) centered at 40 GHz-band with a 2.5 ％ FBW (Fractional Bandwidth) were used. The employed substrate has relative dielectric constant of 2.2 and thickness of 10 mil of Rogers RT/Duroid 5880. Accroding to design and measurement results, a good performance of insertion loss of 2 ㏈ and return loss of -30 ㏈ is achieved at full input/output ports.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.2
• /
• pp.97-104
• /
• 2017

In this paper, we designed and fabricated the multi band Transceiver Assembly(TCA) for the Multi Channel Synthetic Aperture Radar(MCSAR) containing C-band, X-band, Ku-band and we researched to verify electrical performance of TCA. The transceiver consists of transmitters, receivers, signal selection modules for each band, and stability oscillator, frequency synthesizer, controller, power distributor. The transceiver has a receive path selection and bandwidth selection functions in accordance with the operating mode. And the transceiver can transmit and receive all three bands simultaneously, each band has a bandwidth of up to 300 MHz. Final transmission output of transceiver for each band is over 20 dBm to be suitable for driving the T/R module. Receiver bandwidth is selected according to the required function and receiver gain has approximately C-band 52 dB, X-band 50 dB, Ku-band 60 dB, the maximum noise figure of Ku-band V polarization is 4.28 dB in the whole band H, V polarization. As a result of the electrical performance test, a multi-band TCA is satisfied the property requirements of the MCSAR.

• Journal of Biomedical Engineering Research
• /
• v.25 no.6
• /
• pp.471-478
• /
• 2004

Electromyogram (EMC) signal generated by voluntary contraction of muscles is often used in a rehabilitation devices such as an upper limb prosthesis because of its distinct output characteristics compared to other bio-signals. This paper proposes an EMG-based human-computer interface (HCI) for the control of the above-elbow prosthesis or the wheelchair. To control such rehabilitation devices, user generates four commands by combining voluntary contraction of two different muscles such as levator scapulae muscles and flexor-extensor carpi ulnaris muscles. The muscle contraction is detected by comparing the mean absolute value of the EMG signal with a preset threshold value. However. since the time difference in muscle firing can occur when the patient tries simultaneous co-contraction of two muscles, it is difficult to determine whether the patient's intention is co-contraction. Hence, the use of the comparison method using a single threshold value is not feasible for recognizing such co-contraction motion. Here, we propose a novel method using double threshold values composed of a primary threshold and an auxiliary threshold. Using the double threshold method, the co-contraction state is easily detected, and diverse interface commands can be used for the EMG-based HCI. The experimental results with real-time EMG processing showed that the double threshold method is feasible for the EMG-based HCI to control the myoelectric prosthetic hand and the powered wheelchair.