• Journal of Satellite, Information and Communications
• /
• v.7 no.1
• /
• pp.97-101
• /
• 2012

The TC&R(Telemetry, Command & Ranging) antennas should have the hemispherical omni antenna patterns to make sure that the communication link between the satellite and the ground station can be established under whatever satellite attitude during after launch to on-orbit mission. The hemispherical omni-antennas are typically placed on the +z axis and -z axis of the satellite to provide the spherical omni patterns. The S-band qaudrifilar helix antennas having RHCP and LHCP hemispherical omni pattern are designed to meet the antenna gain and the axial ratio requirements. To investigate the omni-antenna pattern characteristics depending on four cases of antenna polarization combination placed on the +z axis and -z axis, the antenna pattern of each case is analyzed. Based on the result, after installing the designed RHCP and LHCP S-band omni-antennas on the +z axis and -z axis of the satellite, the combined antenna gain is obtained and finally analyzed in conjunction with the communication link influence.

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.4
• /
• pp.156-161
• /
• 2015

In this paper, a dual-polarized multi-band multi-layer antenna for a vehicle, which operates in the GPS, bluetooth, and DSRC bands, was implemented. The antenna was designed as a multi-layer structure, and a FR4-epoxy substrate with =4.4 and =1.6mm was used. GPS and DSRC antennas have circular polarized characteristics, and a single probe feeding method was applied. Simulated results by Ansys HFSS v11 was compared with the measured ones. The size of the optimally designed antenna is $67mm{\times}67mm{\times}4.8mm$, -10dB bandwidth of the anatenna was measured to be 820MHz, 127MHz, and 862MHz in each band, and 3dB AR bandwidth of the antenna was simulated to be 19MHz and 110MHz in GPS and DSRC bands. The results confirmed that suggested system satisfies the system requirements.

• Journal of Advanced Navigation Technology
• /
• v.27 no.4
• /
• pp.463-468
• /
• 2023

In this paper, we proposed reconfigurable dual polarization patch array antenna that can select two polarizations(Vertical, RHCP) using defected ground structure and Pin diode. The proposed antenna was designed arranging a circular polarization patch antenna implemented with a square microstrip patch and two slots 3x3 at 25.8mm placed, a half-wavelength of 5.8 GHz. Conect the pin diode and the capacitor to the slot diagonally placed on the ground of each antennas, and select polarization using the open/short operating according to the application of DC voltage to the pin diode. As a result of the design, the gain of the antenna is 11.7 dBi at vertical polarization and 11.6 dBic at RHCP. The axial ratio is 20.3 dB at 1.8 dB vertical polarization at RHCP. Mutual Coupling is Maximum to -20.8 dB for vertical polarization and Maximum to -30.1 dB for RHCP.

• Journal of Biosystems Engineering
• /
• v.22 no.2
• /
• pp.237-246
• /
• 1997

Shucking(removing the meat from the shell) an oyster requires that the muscle attachments to the two shell valves and the hinge be severed. Described here is the computer vision software needed to locate the oyster hinge line so it can be automatically severed, one step in development of an automated oyster shucker. Oysters are first prepared by washing and trimming off a small shell piece on the oyster hinge end to provide access to the outer hinge surface. A computer vision system employing a color video comera then gabs an image of the hinge end of the oyster shell. This image is Processed by the computer using software. The software is a combination of commercially available and custom written routines that locate the oyster hinge. The software uses four feature variables, circularity, rectangularity, aspect-ration, and Euclidian distance, to distinguish the hinge object from other dark colored objects on the hinge end of the oyster. Several techniques, including shrink-expand, thresholding, and others, were used to secure an image that could be reliably and efficiently processed to locate the oyster hinge line.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.2
• /
• pp.157-167
• /
• 2003

In this paper, to reduce the resonant length of patch, microstrip patch antenna of linear polarization which is suppressed at two radiation edges is designed and fabricated at the frequency of 1.575 GHz. The result is like that the resonant length of patch is 45 mm and the length reduction effect is 43.8 % when it is compared with that(80 mm) of plane type. The gain is 4.4 dBd and -3 dB beamwidths are 112$^{\circ}$ and 66$^{\circ}$ in the E-plane and H-plane, respectively. Also, to reduce the size of patch, microstrip patch antennas those are suppressed at four radiating comers are designed and fabricated at the same frequency in the linear and circular polarization, respectively. For linear polarization, at the 1.2 of width/length(W/L) ratio, the patch area is 53 mm $\times$ 63.6 mm and the size reduction effect is 56.1 % when compared with that(80 mm $\times$ 96 mm) of plane type. The gain is 4.3 dBd and the -3 dB beamwidths are 120$^{\circ}$ and 78$^{\circ}$ in the E-plane and H-plane, respectively. For circular polarization, the patch size(54.2 mm $\times$ 61.5 mm) is reduced by 47.2 % than that(76 mm $\times$ 83 mm) of plane type. -3 dB beamwidth of horizontal polarization in the z-x plane and vortical polarization in the y-z plane are 108$^{\circ}$ and 93$^{\circ}$, respectively and this means the increasement in both planes by 52$^{\circ}$ and 27$^{\circ}$ than those of plane type. The maximum gain is 2.5 dBd in the horizontal polarization in the z-x plane. Axial ratio is 1.5 dB at 1.575 GHz and the 2 dB axial ratio bandwidth(ARBW) is 20 MHz(1.3 %).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.2
• /
• pp.192-201
• /
• 2003

In this paper, to reduce the size of patch, three types of 3-dimensional patch antennas which are one-directionally-corrugaged type, rectangular ring-likely corrugated type, and lattice-likely corrugated type rectangular microstrip patch antennas(MPA) are designed and fabricated at the 1.575 GHz. As the result, one-directionally corrugated rectangular MPA is reduced in the resonant length of patch by 21.4% than that of general plane MPA. -10 dB bandwidth(B.W) is 62 MHz(3.9 %) and this is broader than that(39 MHz, 2.5 %) of plane MPA by 23 MHz(1.5 %). The gain is 5.8 dBd and this is reduced by 0.9 dB than that(6.7 dBd) of plane MPA. Half power beamwidth(HPBW) is broadened by 18$^{\circ}$ than that of plane MPA in the E-plane and this is due to the reduced length of patch. For rectangular ring-likely corrugated retangular MPA, the patch size is miniaturized by 21.6 % than that of plane MPA. For lattice-likely corrugated rectangular MPA, in the linear polarization, the size of patch is miniaturized by 43.3 % than that of plane MPA. -10 dB B.W is 70 MHz(4.4 %) and this is broadened than that of plane MPA by 31 MHz(2 %). Gain is 2.2 dBd and this is smaller than that of plane MPA by 4.5 dB. HPBW is increased in both E-plane and H-plane by 22$^{\circ}$ and 13$^{\circ}$, respectively. For circular polarization, the size of patch is reduced by 41 % than that by 41 %. The axial ratio(AR) is 0.8 dB at the 1.575 GHz and the axial ratio bandwidth(ARBW) within 2 dB is 20 MHz(1.27 %) and this is increased by 10 MHz(0.63 %) than that 10 MHz(0.63 %) of plane MPA. From all the results above, it is conformed that the proposed antenna has merit in size reduction of patch and in the input impedance B.W, and is more profitable in many application than the general plane type MPA.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.5
• /
• pp.38-43
• /
• 2015

In this paper, we present novel dual-band microstrip antennas using inverted-L-shaped parasitic elements vertically at radiation apertures for GPS L1(1.575 GHz) and L2(1.227 GHz) bands. For making dual band which has large interval, the inverted-L-shaped parasitic element was loaded at the radiation aperture of a half-wavelength patch antenna(GPS L1) in opposite direction of the feeding point for receiving the low frequency(GPS L2). The low frequency occurs by perturbation and coupling between the patch and parasitic. Next, due to use circular polarizations at the GPS applications, two inverted-L-shaped parasitic elements were loaded at radiation apertures of each polarizations and the feeding point was moved at diagonal part of the patch. The dimensions of the designed circularly polarized antenna were $88.5{\times}79{\times}10.4mm^3$ ($0.36{\lambda}L{\times}0.32{\lambda}L{\times}0.04{\lambda}L$, ${\lambda}L$ is the free-space wavelength at 1.227 GHz). Measured -10 dB bandwidths were 116.3 MHz(7.4%) and 64.3 MHz(5.2%) at GPS L1 and L2 bands, respectively. All of these cover the respective required system bandwidths. The measured 3 dB axial ratio bandwidths were 11.7 MHz(0.74%) and 14 MHz(1.14%), respectively. Within each of the designed bands, broadside radiation patterns were observed.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.10
• /
• pp.71-79
• /
• 2014

In this paper, the microstrip array antenna is studied to replace the parabolic antenna in the direct satellite reception. A microstrip array antenna has been used in extremely limited area, but if it is applied to practical life like a direct satellite reception antenna, we expect that it will be used in various way. First of all, if we use a microstrip array antenna for a direct satellite reception antenna, it should be guaranteed characteristics of broadband frequency. Therefore, the goal of this paper is designing technique an antenna which guarantees broadband frequency band for a direct satellite reception. In this paper, the proposed microstrip antenna is fed by orthogonal two feed lines to a rectangular patch and a sequentially rotated feeding technique is designed proposed for a good axial ratio in broadband frequency band. The rectangular patch is designed to satellite reception band, and the width and length are W=L=8.9 mm ($0.352{\lambda}o$) respectively. The antenna's ground plane has dimensions of $250{\times}250mm$. The experimental results verify that the proposed antenna had the axial ratio of above 1dB broader than that of the conventional feeding antenna. In order to verify the performance, a $8{\times}8$ array having two pairs was fabricated and tested. The maximum gain is 20.8 dB, the sidelobe level confirm less than -10 dB. It is verified by link budget calculation that C/N=6.7 dB can be obtained for domestic use if this proposed antenna is used in Koreasat reception system.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.1
• /
• pp.111-116
• /
• 2017

We propose the compact circular polarized antenna. The radiation elements of the proposed antenna is designed using FR4 substrate with the size of $25mm{\times}3.2mm{\times}5mm$ and stand on four corners of the feed network substrate. The feeder network is designed on FR4 substrate with the size of $40mm{\times}40mm{\times}0.8mm$ and has four oupt signals with same magnitude and $90^{\circ}$ phase difference. The input impedances of the designed radiation elements and the output impedances of the feeder network are $100{\Omega}$. The designed antenna has the dimension of $40mm{\times}40mm{\times}5.8mm$ and the operated frequency band of 1.559 - 1.609 GHz. The fabricated antenna has RHCP radiation pattern and the measured results of axial ratio less than 3.5 dB and radiated gain more than 1.5 dBic. The fabricated antenna can apply to GLONASS and Beiodu systems as well as GPS system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.492-501
• /
• 2013

In this paper, a multi polarization reconfigurable microstrip antenna that can be used selectively for four polarizations(vertical polarization, horizontal polarization, right hand circular polarization, left hand circular polarization) at the S-band is presented. The proposed antenna consists of four PIN diodes and a microstrip patch with a cross slot and a circular slot and is fed by utiliting electromagnetic coupling between the microstrip patch and the feed line. The proposed antenna has a DC bias network to supply DC voltage to each PIN diode and the polarization can be determined by controlling the ON /OFF states of four PIN diodes. The fabricated antenna has a VSWR below 2 in the vertical polarization(3.17~3.21 GHz), the horizontal polarization(3.16~3.20 GHz), the left hand circular polarization (3.08~3.19 GHz), and the right hand circular polarization(3.10~3.2 GHz) frequency bands. The designed antenna has the cross polarization level higher than 20 dB, a gain over 5 dBi for the linear polarization states, and 3 dB axial ratio bandwidth wider than 50 MHz in the circular polarization states.