• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1269-1278
• /
• 2013

The cutting area changes periodically in the end-milling process because of its form generation mechanism. In this study, the effects of the cutting area on end-milled side walls are studied by developing a cutting area model that simulates the area formed by engagement between a workpiece and a cutting edge of the end mill. To do this, the straightness profile of the side wall in the axial direction is investigated. Models for estimating the cutting area and the transition point, where the slope of the straightness profile changes suddenly, are verified from real end-milling experiments under various radial and axial depth of cut conditions. Through this study, it is confirmed that the final end-milled side wall is generated in the regions where cutting areas are constant and decreasing in the down-cut. Similarly, in stable up-cut, it is also generated in the regions where cutting areas are increasing and constant. It is found that the transition point appears when the region changes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1183-1189
• /
• 2015

This study focuses on the design of the tapered joints of a wind power turbine. The main variables of the tapered joint are the transmitted torque, shaft diameter, contact area of the tapered ring, and tightening torque of the bolts, which applies a compressive pressure from the hub to the shaft. The stress distribution of the taper fit was calculated under axisymmetric plane strain conditions because of the small taper angle. The axial displacement of the clamp can be calculated from the radial elastic deformation and the taper angle. The stress field of each ring is obtained from the cylinder stress equation. To verify the accuracy of the calculation, finite element (FE) analysis was performed, and the results of the calculation and FE analysis were compared. The hoop stress of the tapered surface showed a discrepancy of approximately 10, but the trends of the stress distributions of each component and the relative movement obtained by FE analysis were in good agreement with the analytical calculation results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.210-216
• /
• 1994

본 연구에서는 볼 베어링의 전동체 회전에 의해 발생하는 원심력, 자이로스코픽 모멘트, 하중 방향선에 대한 전동체의 하중 분포 변화 등을 고려하여, 볼 베어링의 강성 특성을 해석하고, 볼 베어링으로 지지되는 간단한 회전축 계에 해석 결과를 적용하여 진동 특성을 해석하고자 한다.

• Computational Structural Engineering
• /
• v.7 no.2
• /
• pp.11-15
• /
• 1994

본 고에서는 축대칭회전 Shell을 해석모델로 선정하여 주로 Shell의 휨 강성이 구조체의 거동에 미치는 영향에 대하여 검토하였다. 어떠한 구조형식이든 외력의 작용하에서 발생되는 응력이 축방향력 뿐이라는 것은 상당히 합리적이고 역학적으로도 명쾌한 동시에, 실제 설계상 이상적인 판단기준을 부여하지만, 실제로는 필히 휨상태를 수반하게 된다. 이러한 휨상태는 구성요소의 휨강성에 크게 의존하고 있고, 구조체에 어느정도의 휨강성을 부여하므로써 작용하중에 대한 저항능력의 증가, 변형 및 응력의 저감에 효과적이라는 것을 알 수 있다. 본 고에서는 등방성 Shell에 대한 선형 해석결과만을 게재하였으나, 이러한 성상은 여러가지 영향인자(지지조건, 하중상태 등)에 따라 아주 상이하게 나타나기 때문에 세심한 고찰이 필요하다고 할 수 있다.

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.189-200
• /
• 2017

Nonplanar structural walls with C-shaped and H-shaped sections have been used as an efficient lateral force-resisting system for building structures. Since the nonplanar walls are subjected to axial load and bending moments about two orthogonal axes, complicated section analysis is required for flexure-compression design. In the present study, a straightforward design method for biaxially loaded C- and H-shaped walls was proposed by modifying the existing load contour method for columns with symmetric solid sections. For this, a strain compatibility section analysis program that can calculate biaxial moment strengths of arbitrary wall section was developed and its validity was verified by comparing with existing test results. Then, through parametric study, the interaction of biaxial moments at constant axial loads in prototype C- and H-shaped walls was investigated. The results showed that, due to unsymmetrical geometry of the wall sections, the biaxial interaction was significantly affected by the moment directions and axial loads. From those investigations, non-dimensional contour equations of the biaxial moments at constant axial loads for C- and H-shaped walls were suggested. Further, design examples using the proposed contour equations were given for engineering practice.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.1
• /
• pp.1-11
• /
• 2024

The purpose of this paper is to suggest a method for applying a reasonable dam axial seismic load loading method and load-bearing capacity evaluation method in the dynamic analysis of the pier part of a concrete dam to which the seismic force of the collapse prevention level is applied. To this end, the pier part of a concrete dam was selected as a target facility, and the characteristics of the dynamic behavior in the axial direction of the weir dam were analyzed through dynamic analysis applying various weir widths, and 'U.S. The load-bearing capacity evaluation was performed by applying the RC hydraulic structure evaluation technique suggested by the Army Corps, 2007'. As a result of the study, when applying seismic force in the axial direction of the pier part, it is more realistic to assume that the axial direction of the weir part dam behaves as a rigid body and 'U.S. Army Corps, 2007' suggested that the method of reviewing the load-bearing capacity for moment and shear was considered reasonable, so it was concluded that improvement of the current evaluation method was necessary. If the improvement of the research result is applied, it will have the effect of deriving more reasonable evaluation results than the current seismic performance evaluation method using CLE. It is judged that additional research is needed in the future on the torsional moment occurring in the pier part.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.466-475
• /
• 2001

The potential shear strength of reinforced concrete beams decreases after flexural yielding due to the decrease of the effective compressive strength of concrete in plastic hinge zone. A truss model considering shear deterioration in the plastic hinge zone was proposed in order to evaluate the ductile capacity of reinforced concrete beams failing in shear after flexural yielding This model can determine the potential shear strength of the beam by using a truss model. The potential shear strength gradually decreases as the increase of the axial strain of member. When the calculated potential shear strength decreases up to the flexural yielding strength, the corresponding rotation angle is defined as the ductile capacity of the beam. The predicted ductile capacity of reinforced concrete beams is shown to be in a good agreement with experimental results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.9
• /
• pp.890-899
• /
• 2010

An experimental study has been conducted to analyze the operating forces on a partially admitted turbine blade using a linear cascade apparatus. Axial-type blades were used and the blade chord was 200mm. The rectangular nozzle was applied and its size was $200mm{\times}200mm$. The experiment was done at $3{\times}10^5$ of Reynolds number based on the chord. The rotational force and axial force on the blade were measured at steady state by moving the blade to the rotational direction. The operating forces were measured at three different nozzle install angles of $58^{\circ}$, $65^{\circ}$ and $72^{\circ}$ for off-design performance test. In addition, three different solidities of 1.25, 1.38 and 1.67 were applied. From the results, the maximum rotational force was increased when the solidity was decreased and the nozzle install angle was decreased. The axial force was increased by decreasing the nozzle install angle. The reverse axial force was obtained in the partially admitted region when the nozzle install angle was increased to $72^{\circ}$.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.7
• /
• pp.25-32
• /
• 2004

This paper examines the results of full-scale field tests on micropiles and side resistance is evaluated with respect to axial displacements and soil properties. Both cohesive and cohesionless soils are included in this evaluation. For all practical purposes, the developed load-displacement relationship and the geotechnical soil properties for each micropile and soil type can be used to represent the available data well through normalized average values and empirical correlations. There is a significant difference in load-carrying capacity between micropiles and drilled shafts that results primarily from the micropile pressure-grouting installation effects on the state of stress in the ground. The results show that micropiles can have a significant increase of capacity over larger-diameter drilled shafts at shallower depths with D/B < 100 or so. In cohesive soils, the typical increase is on the order of 1.5 with values as high as 2.5. For cohesionless soils, the typical increases are in the range of 1.5 to 2.5 with values as high as 6.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.3 s.70
• /
• pp.355-363
• /
• 2004

In order to obtain the effective length factor of beam-column members of plane frames, this paper extensively used an alignment chart approach, based on the nomograph given in LRFD-AISC specification commentaries. However, it should be noted that various simplifications and assumptions were introduced in constructing the alignment chart. To overcome the practical limitations of the alignment chart, this paper proposes a simple but accurate procedure that determined the effective buckling length for stability design of main members of cable-supported bridges. This method requires the full system buckling analysis. The numerical examples showing the suitability of the present scheme are discussed and some conclusions are drawn.