• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.739-745
• /
• 2017

Research of ADN-based monopropellant thruster is progressed by developed countries in Europe to replace toxic hydrazine, and ADN-based monopropellant thruster system is the only system that was proved in space environment. In this research, ADN-based propellant and catalyst was fabricated to develop ADN-based monopropellant thruster, and catalytic combustion performance with fabricated propellant and catalyst were evaluated with DSC-TG analysis. Catalytic combustion of propellant and catalyst was determined with firing test using 5 N scale liquid monopropellant thruster.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.377-382
• /
• 2010

The Present study uses non-Newtonian simulant gel propellant mixed by Water, Carbopol 941, and NaOH solution in order to analyze the gel propellant flow behavior. Rheological data have been measured and obtained prior to the analysis of flow characteristics where water-gel propellant as well as water-gel propellant with $Al_2O_3$ nano particles are both used. The critical Dean number were examined by numerical simulation of gel propellant in the U-shape duct flow. It is found that though gel-nano propellants have higher apparent viscosity, the critical Dean number did not showed notable difference with respect to the water-gel propellant. It is believe that this is due to the fact that the power law index of both propellants have close value, as was demonstrated by Fellouah et al.[1]

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.34-37
• /
• 2007

Propellant filling and holding test was carried out using liquid oxygen as a working fluid. The feeding line system has a filter at propellant tank outlet. Vaporization of liquid oxygen during holding after completion of filling and effect of vaporization to recirculation performance in this system was observed. Filling rate and pressure of tank ullage had the effect on state of liquid oxygen in feeding line. There was no geysering in feeding line during holding because of the position of filter.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.221-224
• /
• 2010

Recently, due to the enormous cost for sending a satellite into an orbit, small and more reliable satellites have been more demanded. An introduction of new binders(HTPB, GAP) and new oxidizers made great improvements of the large thrust modulation. In order to make cost reduction, one prefers to the low melting temperature thermoplastic propellant reforming the manufacturing process dramatically. Solid propellant rockets have been had a problem of the injection accuracy into orbit, but PBS(Post Boost Stage) using a liquid mono-propellant improves the injection accuracy. This paper also gives the direction of the advanced nozzle materials and the motor case.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.185-188
• /
• 2009

The rocket motor of the space launch vehicle offers thrust for satellite to enter into the orbit. Characters of the solid propellant for rocket motors are affected by the space conditions such as vacuum and space radiation. The solid propellant used for such a purpose should not undergo physical, internal ballistic and energetic changes when exposed to vacuum and space radiation. This study describes the development of the solid propellant composition for the rocket motor of the space launch vehicle. Also, experimental study was conducted on supersonic diffuser in order to verify the performance of the solid propellant composition which was applied to standard motor on the ground in the vacuum condition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1735-1740
• /
• 2010

The propellant KM10, a single propellant manufactured nitrocellulose, is known to cause natural degradation phenomena at long term storage. The self-life was estimated using generally used high temperature acceleration aging tests to analyze the content of stabilizer and using the Arrhenius equation & Berthelot equation to calculate reaction rate constants. According to the result of this study, self-life of propellant KM10 using the Arrhenius equation & Berthelot equation appear significantly different as 43.73, 16.53years and when compared with the paper of E. R. Bixon, self-life of propellant KM10 predicted using the Arrhenius equation was reasonably determined.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.84-90
• /
• 2004

A performance evaluation is made in terms of thrust, impulse bit. and specific impulses for a set of mono-propellant hydrazine thrusters producing 0.95 lbf of nominal thrust at an inlet pressure of 350 psia. With a brief description on the hot-firing test configuration and procedures. a typical data obtained from steady-state firing mode is given directly showing the variational behavior of propellant supply pressure, mass flow rate, vacuum condition, and thrust. The performance features are successfully compared to the reference criteria of 1-lbf standard mono-propellant rocket engine. Additionally. a statistical inter-thruster treatment is concisely depicted for the justification of selected thrusters as a grouped member of flight model for spacecraft propulsion system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.6
• /
• pp.28-33
• /
• 2022

In this study, the curing characteristics of commonly used Hydroxyl terminated polybutadiene(HTPB)-based solid propellant according to the curing temperature and Equivalent ratio change were investigated. In addition, the effect of curing reaction according to their ratio and content in the Triphenyl bismuth(TPB), Maleic anhydride(MA) and Magnesium oxide(MgO) catalyst systems was confirmed. Finally, moisture was added for each propellant mixing process to check the effect of moisture on propellant curing.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.233-239
• /
• 2003

The present study has numerically investigated the combustion processes in the solid propellant rocket engine. The two step global reaction model for condensed phase and five step global reaction mechanism for gas phase are adopted to predict the detailed flame structure near double-base solid propellant surface. The turbulence-chemistry interaction is represented by the PaSR(Partially Stirred Reactor) model. To reduce the uncertainties for convective heat transfer near solid fuel surface having strong blowing effect, the Low Reynolds number k-$\varepsilon$ turbulent model is employed. Based on numerical results, the detailed discussion has been made for the turbulent combustion processes and transient behavior of pressure and temperature fields in the solid propellant rocket engine.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.58-67
• /
• 2021

This paper describes the development for the dual thrust rocket motor with two types of propellants with different combustion characteristics. We developed the composition of two kinds of propellant to be applied to a rocket motor, and improved a propellant charging process in a free grain type to improve the adhesion method and the problems of adhesion between different propellants. In addition, to meet the ignition phenomenon as a small rocket motor, the ignition delay was improved by applying a nozzle plug developed in a high density foam. The propulsion rocket motor reflecting this design and the improved manufacturing process was evaluated through a ground performance test.