• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.5
• /
• pp.471-479
• /
• 2006

Automatic transfer equipments of manufacturing and process line trend toward big size as LCD glass is big size, heavy weight. The conventional stocker uses rotational motor and mechanical power converter device as travel axis of stocker crane and then frequent maintenances by complex structure and mechanical friction are required. Also it has problem to minimize the particle generation. To solve these problems, this paper verified the performance of permanent magnet(PM) excited transverse flux linear motor(TFLM) that is big power density per unit volume applied for travel axis of 7 generation stocker that is being big size, high power, long distance by the experiment based on proposed control algorithm, controller and power converter device.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.794-801
• /
• 2017

When a radial wheel is placed so as to partially overlap a conductive plate and rotated, a lift force is generated on the wheel, a thrust force along the edge, and a lateral force which tends to reduce the overlap region. When several of these wheels are combined, it is possible to realize a system in which the stability of the remaining axes is ensured, except in the traveling direction. To validate the overall characteristics of the multi-wheel system, we propose a transfer system levitated magnetically using radial electrodynamic wheels. The proposed system is floated and propelled by four wheels and arranged in a structure that allows the thrusts generated by the front and rear wheels to offset each other. The dynamic stability of the wheel and the effect of the pole number on the three-axial forces are analyzed by the finite element method. At this time, the thrust and levitation force are strongly coupled, and the only factor affecting them is the wheel rotation speed. Therefore, in order to control these two forces independently, we make use of the fact that the ratio of the thrust to the levitation force is proportional to the velocity and is independent of the size of the gap. The in-plane and out-of-plane motion control of the system is achieved by this control method and compared with the simulation results. The experimental results show that the coupled degrees of freedom can be effectively controlled by the wheel speed alone.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.5
• /
• pp.514-523
• /
• 2008

This paper presents a single-axis simulator developed to verify the attitude control algorithm of KAUSAT-2 satellite. Named KAUSatSIM, the simulator is composed of a single-axis rotation table using an air-bearing that simulates a frictionless environment, as well as sensors and momentum wheel that was used on KAUSAT-2. The simulator can be utilized for verification of KAUSAT-2 attitude control algorithm, development of new algorithms, and verification of performance. Tests were performed on the single-axis rotation simulator using the momentum wheel in order to verify the attitude control algorithm of KAUSAT-2. Satisfactory test results were obtained by designing a wheel controller that employs the proportional-derivative control method. In addition, a propulsion system was added and tested for development of a new satellite attitude control algorithm.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.891-898
• /
• 2007

Optimal aerodynamic design for the pitch-controlled horizontal axis wind turbine and its aerodynamic performance for various pitch angles are performed numerically by using the blade element momentum theory. The numerical calculation includes effects such as Prandtl‘s tip loss, airfoil distribution, and wake rotation. Six different airfoils are distributed along the blade span, and the special airfoil i.e. airfoil of 40% thickness ratio is adopted at the hub side to have structural integrity. The nonlinear chord obtained from the optimal design procedure is linearized to decrease the weight and to increase the productivity with very little change of the aerodynamic performance. From the comparisons of the power, thrust, and torque coefficients with corresponding values of different pitch angles, the aerodynamic performance shows delicate changes for just $3^{\circ}$ increase or decrease of the pitch angle. For precisive pitch control, it requires the pitch control algorithm and its drive mechanism below $3^{\circ}$ increment of pitch angle. The maximum torque is generated when the speed ratio is smaller than the designed one.

• Journal of Advanced Navigation Technology
• /
• v.16 no.1
• /
• pp.1-7
• /
• 2012

In this research, a single-axis attitude control test bed is developed, and simulation and tests experiments are performed, as a preliminary research of a quad-rotor aerial vehicle development. A single-axis test bed with seesaw configuration is manufactured using two motors and propellers, and the aerodynamic parameters are derived by thrust tests. The response of the system is estimated with Matlab/Simulink, and experiments are performed with attitude control computer and an attitude sensor onboard the test bed. Comparing the results of simulated and tested data, factors of steady-state errors during experiments are found, and performances of used attitude control algorithm and the control computer were verified. In these process, essential preliminary data for attitude control of a quad-rotor unmanned aerial vehicle were acquired.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.5
• /
• pp.399-406
• /
• 2016

The large scale wind turbine blades usually experience periodic change of inflow speed due to blade rotation inside the ground shear flow region. Because of the vertical wind shear, the inflow velocity in the boundary layer region is maximum at uppermost position and minimum at lowermost position. These spatial distribution of wind speeds can lead to the periodic oscillation of the 6-component loads at hub and low speed shaft of the wind turbine rotor. In this study we compare the aerodynamic loads between two inflow conditions, i.e, uniform flow (no vertical wind shear effect) and normal wind profile. From the computed results all of the relative errors for oscillating amplitudes increased due to the ground shear flow effect. Especially bending moment and thrust at hub, and bending moments at LSS increased enormously. It turns out that the aerodynamic analysis including the ground shear flow effect must be considered for fatigue analysis.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.163-166
• /
• 2005

사이클로콥터는 회전축에 평행하게 회전하는 블레이드로 구성된 사이클로이드 블레이드 시스템으로부터 추력을 얻는 수직이착륙 무인기이다. 본 논문에서는 공기역할을 고려한 최적 설계를 통해 결정된 로터 형상을 갖는 사이클로콥터에 대해서 구조 해석을 수행하였다. 복합재료 블레이드의 적층각, 적층수 등을 MSC/NASTRAN 과 반응면 기법 등에 의해서 결정하였다. 블레이드를 포함한 로터 정적 해석을 통해 각 요소가 허용 응력 이내의 값을 가짐을 확인하였고, 동적 해석을 통해 주요 저차 모드가 로터 회전과 불일치하게 함으로써 공진의 가능성을 없앴다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.150-156
• /
• 2006

A Flapping foil Produces an effective angle of attack, resulting in a normal force vector with thrust and lift components, and it can be expected to be a new highly effective propulsion system. A heaving foil model was made and it was operated within a circulating water channel at low Reynolds numbers. The unsteady thrust and lift acting on the heaving foil were measured simultaneously using a 6-axis force sensor based on force and moment detectors. We have been examined various conditions such as heaving frequency and amplitude in NACA 0010 Profile. The results showed that thrust coefficient and efficiency increased with reduced frequency and amplitude. We also Presented the experimental results on the unsteady fluid forces of a heaving foil at various Parameters.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.426-430
• /
• 2005

The COMS(Communication, Ocean and Meteorological Satellite) is the first developed three-axis stabilization multi-function satellite on geostationary earth orbit(GEO) in korea, presently scheduled to be launched in 2008. The COMS propulsion system provides the thrust and torque required for the insertion into GEO, attitude and orbit control/adjustment of spacecraft. In this paper, system design of propulsion system, basic functions and design requirement of components are described.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.222-227
• /
• 2005

A Flapping foil produces an effective angle of attack, resulting in a normal force vector with thrust and lift components, and it can be expected to be a new highly effective propulsion system. A heaving foil model was made and it was operated within a circulating water channel at low Reynolds numbers. The unsteady thrust and lift acting on the heaving foil were measured simultaneously using a 6-axis force sensor based on force and moment detectors. We have been examined various conditions such as heaving frequency and amplitude in NACA 0010 profile. The results showed that thrust coefficient and efficiency increased with reduced frequency and amplitude. We also presented the experimental results on the unsteady fluid forces of a heaving foil at various parameters.