• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.201-205
• /
• 2011

In a cryogenic propellant tank the pressurant is contracted due to heat loss and the propellant itself evaporates. On a restartable propulsion system such phenomena are more intensive because the propellant contacts with the pressurant on the larger surface during the coast flight. Such heat and mass transfer phenomena should be considered for estimating the amount of pressurant. On the hypothesis that the heat and mass transfer quasi-equilibrium is achieved during the coast flight, the calculation process of the equilibrium pressure is presented. On the process the amount of loaded helium on the Falcon-1 second stage is calculated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.149-152
• /
• 2009

Spray characteristic parameters such as droplet mean velocity, diameter, and volume flux are measured at various locations of spray in order to investigate the evolutionary feature of droplets exiting from a direct-injection type thruster nozzle-orifice. The experimental results indicate that the large droplets with high velocity at the center of upstream are broken-up into smaller droplets with low velocity due to their continuous momentum loss to surrounding air along with spray evolution toward downstream. Also it is found that the high volume flux expands its distribution in radial direction as a results of spray spreading and dispersion.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.10
• /
• pp.112-119
• /
• 2003

Design analysis and grow1d test on propellers for 50 m-long airship propulsion were conducted. The design analysis code developed by adopting the vortex-blade-element theory was applied to the design of optimum propeller at the condition of maximum flight speed at sea level. In order to validate the performance of the propeller, ground test of the propeller was performed, and thrust and torque were measured for several different pitch angles at static condition. The power coefficients and thrust coefficients obtained by the test compared well with the analysis results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.68-75
• /
• 2017

Dual bell nozzle is a type of altitude compensation nozzle, which is a nozzle that minimize the losses of the specific impulse at the off-design point of a typical bell nozzle. In this paper, numerical computations are performed to understand the transition characteristics of dual bell nozzles with fixed expansion ratios. The major design variables are the length of extension and the angle of inflection. As the length of the extension increased, the transition altitude and transition duration increased and the reduction of the thrust coefficient decreased. As the angle of inflection increased, the transition altitude and transition duration decreased and the reduction of the thrust coefficient increased.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.294-298
• /
• 2001

Satellite propulsion system is employed for orbit transfer, orbit correction, and attitude control. The monopropellant feeding system in the low-earth-orbit satellite blowdowns fuel to the thrust chamber. The thrust produced by the thruster depends on fuel amount flowed into the combustion chamber. If the thruster valve be given on-off signal from on-board commander in the satellite, valve will be opened or closed. When the thrusters fire fuel flows through opened thruster valve. Instantaneous stoppage of flow in according to valve actuation produces transient pressure due to pressure wave. This paper describes transient pressure predictions of the KOMPSAT2 propulsion system resulting from latching valve and thrust control valve operations. The time-dependent set of the fluid mass and momentum equations are calculated by Method of Characteristics (MOC).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.4
• /
• pp.562-569
• /
• 1997

The axial position of an impeller is misaligned in the process of manufacturing and assembling. For a single suction centrifugal pump with balancing holes, the effect of axial displacement of impeller on the performance, leakage loss and axial thrust acting on the impeller is experimentally investigated. The axial displacement decreases the pump efficiency, increases the leakage through the clearance between wearing ring and impeller, and affects the characteristics of axial thrust.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.64-71
• /
• 2004

A computational study on the supersonic flow around the lateral jet controlled missile has been performed. For this purpose a three dimensional Navier-Stokes computer code(AADL3D) has been developed and case studies have been performed by comparing the normal force coefficient and the moment coefficient of a missile body for different jet flow conditions including jet pressure and jet Mach number. The results show different behavior of normal force and moment variation according to jet pressure variation and jet Mach number variation. From the detailed flow field analyses, it is verified that most of the normal force loss and the pitching moment generation are taken place at the low-pressure region behind the jet nozzle. Furthermore, it is shown that the pitching moment can be efficiently reduced by obtaining the lateral thrust through higher jet Mach number rather than through high jet pressure.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.25-29
• /
• 2007

Minimization of conventional propulsion device has been studied for altitude control of micro satellite. We studied micro nozzle performance and found higher significant loss for a micro nozzle with smaller nozzle throat diameter. To overcome this loss, we proposed thermal transpiration based micro propulsion system. This new system has no moving parts and can control flow by temperature gradient, and this can be an option for potential new micro propulsion system.

• Journal of Aerospace System Engineering
• /
• v.15 no.1
• /
• pp.32-39
• /
• 2021

Electric propulsion aircraft are being actively researched in the aviation field in recent years to solve environmental and noise problems caused by existing gas turbine engine. In particular, research on a thrust motor as a core component of an electric power propulsion system and an inverter for driving it is actively being conducted. In this paper, a motor with high specific power is selected to determine characteristics of aircraft that are sensitive to weight and volume. Power loss of the inverter is then simulated. In the simulation, the selected motor and power device were modeled using PSIM, a power electronics analysis tool. Inverter power loss according to switching frequency was then analyzed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.2
• /
• pp.72-78
• /
• 2022

A vacuum brazed cooling passage for an aircraft engine controller was designed. In order to predict the total pressure loss, which is the main design factor of the cooling passage, theoretical and numerical methods for the major loss and the minor loss considering the overall shape of the cooling passage are presented. This design and evaluation method can predict the pressure loss of the complex cooling passage shape for various flow conditions at the initial design step.