• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.82-85
• /
• 2006

A trapezoidal fin with various lateral surface slopes is designed optimally by using one-dimensional analytic method. For four different convection characteristic numbers, the trend of heat loss as a function of fin tip length is shown. The optimum heat loss is somewhat arbitrarily chosen as 92% of the maximum heat loss. The optimum fin length corresponding to this optimum heat loss versus convection characteristic number is presented. The optimum effectiveness and specific effectiveness is presented as a function fin shape factor.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.455-456
• /
• 2015

본 논문에서는 무선전력 전송을 위한 평판 나선형 코일의 최적 형상 선정을 위해 각 코일의 형태에 따른 출력 성능을 비교 및 평가한다. 코일 간 결합계수, 각 코일의 Q-factor 측면에서 송수신 패드의 성능을 비교하며, 이를 위해 송수신 패드가 차지하는 면적을 최대한 활용하여 모델링 한다. 모델링한 코일에 대하여 수신패드의 수직 및 수평이동에 대한 성능 지표를 평가하고 코일의 최적 형상을 선정한다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.1
• /
• pp.45-54
• /
• 2012

Optimization of the asymmetric trapezoidal fin with various upper lateral surface slope is made using a two-dimensional analytic method. For the fixed fin base height, the optimum heat loss, fin length and effectiveness are represented as inner fluid convection characteristic number, fin base thickness, fin base height, fin shape factor and ambient convection characteristic number. For this optimum procedure, the optimum heat loss is defined as 95% of the maximum heat loss from the fin. One of the results shows that optimum heat loss and effectiveness seems independent of the fin shape factor while optimum fin length decreases almost linearly as the fin shape factor increases.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.1-7
• /
• 2017

When implementing butt joint welding of two plates, it is useful to attach end-tabs made of a metal with high heat conductivity (e.g., copper) at the front and back sides of the welded plates to prevent the bead from rolling down and prevent defects that may occur at the tips of the weld zone. In this study, the fin shape, which is known to have good heat discharging characteristics by natural convection, has been applied to enhance the cooling performance of the end-tab. From both experiment and numerical analysis, it was confirmed that end-tabs with fin-shaped holes have better heat discharging performance than end-tabs without holes. Through thermal and fluid flow analysis, the cooling rates of end-tabs with different hole shapes were estimated in order to figure out characteristics of shape factor that are important for the heat discharging performance. As a result, we found that the structure including vertical fins with optimal fin gap was the best-performing shape.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.3
• /
• pp.31-41
• /
• 2021

A dozer is a construction machinery used to move soil mass along large open tracts of land. Soil thrust generated on the soil-track interface determines the performance of the dozer; to improve the tractive performance of the dozer, the outer surface of the continuous-track is designed to protrude with grousers. In this study, we calculated soil thrust of the dozer equipped with grousers with various shape ratios, and evaluated the optimal grouser shape ratio considering ground conditions. Grouser generated additional soil thrust on the side of the continuous-track (e.g., side soil thrust) and converted the shearing surface (e.g., from soil-track interface to soil-soil interface), increasing the soil thrust of dozer by about 1.3 to 1.6 times. The effect of grouser's shape ratio on the soil thrust of dozer differed with the relative density of the ground. As the shape ratios of grouser increased, soil thrust of dozer decreased at the relative density of 40% and increased at the relative density of 80%. Based on these results, it can be concluded that the shape ratio of grouser severely affects the dozer's performance; thus, careful consideration of the optimal shape ratio of grouser is of great importance in the mechanical design, evaluation, and optimization of the undercarriage of dozers.

• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.213-224
• /
• 2008

Flexible pavement responses to vehicular loading, such as critical stresses and strains, in each pavement layer, could be predicted by the multilayered elastic analysis. However, multilayered elastic theory suffers from major drawbacks including spatial dimension of a numerical model, material properties considered in the analysis, boundary conditions, and ill-presentation of tire-pavement contact shape and stresses. To overcome these shortcomings, three-dimensional finite element (3D FE) models are developed and numerical analyses are conducted to calculate pavement responses to moving load in this study. This paper introduces a methodology for an effective 3D FE to simulate flexible pavement structure. It also discusses the mesh development and boundary condition analysis. Sensitivity analyses of flexible pavement response to loading are conducted. The infinite boundary conditions and time-dependent history of calculated pavement responses are considered in the analysis. This study found that the outcome of 3D FE implicit dynamic analysis of flexible pavement that utilizes appropriate boundary conditions, continuous moving load, viscoelastic hot-mix asphalt model is comparable to field measurements.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1636-1643
• /
• 2001

Automobile maneuverability and tire durability are significantly influenced by the sidewall tire contour. In order to improve these tire performances, it is very important far one to determine a sidewall contour producing the ideal tension and strain-energy distributions. However, these requirements can nut be simultaneously achieved by conventional non-interactive multi-objective optimization methods based on mathematical programming, because these exhibit the conflicting behavior each other, with respect lo the sidewall contour. Therefore, we execute the tire contour optimization fur improving the maneuverability and the tire durability using satisficing trade-off method.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.2249-2250
• /
• 2008

고온 초전도체를 이용한 에너지 저장장치는 종래의 저온 초전도체를 이용한 장치에 비해 효율이 높고, 설치 면적이 작으며, 환경 친화적 특성을 갖고 있다. 또한 냉각비용이 저렴하고 저장되는 에너지 밀도가 높다. 고온초전도 선의 성능향상이 가속화됨에 따라 고온초전도 선을 이용한 초전도 전력기기의 개발이 활발히 이루어지고 있다. 하지만 초전도 선이 구리선에 비하여 고가라는 단점이 여전히 문제가 되고 있다. 가격적인 측면에서 선의 사용량을 줄이기 위한 대책이 필요하다. 또한 코일의 손실해석은 전력기기의 경제성 여부와 성능향상을 위해 수행되어야 할 중요한 연구 분야 중 하나이다. 본 논문에서는 초전도 선으로 권선한 코일의 자장분포 및 인덕턴스를 유한요소법(FEM)해석을 통해 확인하였으며, 솔레이드 코일, 팬케이크 코일, 트로이달 코일의 저장용량을 결정하기 위해 비교를 통하여 최적의 형상을 도출하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.14-22
• /
• 2007

A reversed trapezoidal fin with variable lateral surface slope is optimized using a two-dimensional analytic method. For a fin base boundary condition, convection from the inside fluid to the inside wall and conduction from the inside wall to the fin base are considered. Heat loss from the fin tip surface is not ignored. The maximum heat loss at the practical fin length, the corresponding optimum fin efficiency, fin length and fin base height are presented as a function of the fin inside and outside convection characteristic numbers. One of the results shows that the optimum fin shape becomes 'fatter and shorter' as the ratio of fin tip height to base height increases.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.12
• /
• pp.1237-1244
• /
• 2015

A gerotor can be manufactured in a miniature size because it has a high discharge per cycle and a simple structure. Gerotors are widely used for the lubrication oil of an engine and as the hydraulic source of an automatic transmission. Recently, improvements in fuel efficiency and noise reduction have come to the fore in the automobile industry, and it has been necessary for better fuel efficiency to continuously improve the flow rate and noise of internal gear pumps through the optimal design of the gerotor and port shape. In this study, gerotors were generated based on the equations derived for a lobe shape with multiple profiles (ellipse 1-elliptical involute-ellipse 2). The ranges of the design parameters were considered to prevent a cusp and loop. In addition, the optimal lobe shape was obtained by determining the influence of the lobe shape on the performances (flow rate, irregularity, etc.), according to the values of the design parameters.