• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.47.2-47.2
• /
• 2010

For reducing outer reflection in mono-crystalline silicon solar cell, wet texturing process has been adapted for long period of time. Nowadays mixed solution with potassium hydroxide and isopropyl alcohol is used in silicon surface texturing by most manufacturers. In the process of silicon texturing, etch rate is very critical for effective texturing. Several parameters influence the result of texturing. Most of all, temperature, process time and concentration of potassium hydroxide can be classified as important factors. In this paper, temperature, process time and concentration of potassium hydroxide were set as major parameters and 3-level test matrix was created by using robust design for the optimized condition. The process optimization in terms of lowest reflection and stable etch rate can be traced by using robust design method.

• Membrane Journal
• /
• v.30 no.1
• /
• pp.21-29
• /
• 2020

In this study, we have established the optimum design condition of pore-filled anion-exchange membrane for all-vanadium redox flow battery (VRFB). From the experimental results, it was proven that the membrane design factors that have the greatest influence on the charge-discharge performance of VRFB are the ion exchange capacity, the porosity of substrate film, and the crosslinking degree. That is, the ohmic loss and the crossover of active materials in VRFB were shown to be determined by the above factors. In addition, two methods, i.e. reducing the ion exchange capacity at low crosslinking degree and increasing the crosslinking degree at high ion exchange capacity, were investigated in the preparation of pore-filled anion-exchange membranes. As a result, it was found that optimizing the crosslinking degree at sufficiently high ion exchange capacity is more desirable to achieving high VRFB charge-discharge performances.

• Tunnel and Underground Space
• /
• v.22 no.4
• /
• pp.257-265
• /
• 2012

In this study, a series of CFD (Computational Fluid Dynamics) simulations carried out to evaluate the optimum design model of the internal flow path of drill bit. The Star-CCM+ code was adopted to simulate the multi-phase discharge flow of rock particles and flushing air during a drilling process. The input parameters for the flow simulation of rock particles and air were obtained from the in-situ drilling test results. After the three design factors were determined, the experimental design method (Taguchi method) was utilized to evaluate the optimum value of each factor.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.2
• /
• pp.141-148
• /
• 1999

변위 근거 유한요소해석을 사용하는 대부분의 위상 최적화 기법은 요소의 안정성 부족으로 인하여 체스판 무늬가 주기적 형태로 반복하여 설계영역 내부에 나타난다. 본 연구에서는 선형요소를 이용하면서 최적화 알고리즘의 안정성에 영향을 주지 않고 간단하게 모든 최적화 알고리즘에 이용 가능한 체스판무늬 형성 방지책을 개발하였다. 본 연구의 체스판무늬 형성 방치책에서는 먼저 각 선형요소를 구성하는 절점들의 부치분율을 설계변수로 선정하고, 요소내부의 부피분율을 설계변수로 표현하기 위한 선형 보간함수로 선형요소들의 형상함수를 선정하였다. 그리고, 설계변수와 등가 재료상수와의 상관 관계식은 평균장 근사이론을 이용하여 균질화된 재료에 벌칙인자가 도입된 관계식을 이용하였다. 또한, 본 연구에서는 순차이차계획법인 PLBA 알고리즘을 이용하여 위상 최적화문제를 해석하였다.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.3
• /
• pp.87-93
• /
• 2018

Ground source heat pump(GSHP) system is one of the high efficiency heat source systems which utilizes the constant geothermal energy of a underground water or soil. However, the design of conventional GSHP system in the domestic market is dependent on the experience of the designer and the installer, and it causes increase of initial installation cost or degradation of system performance. Therefore, it is necessary to develop a guideline and the optimal design method to maintain stable performance of the system and reduce installation cost. In this study, in order to optimize the GSHP system, design factors according to ground heat exchanger(GHX) type have been examine by simulation tool. Furthermore, the design factors and the correlation of a single U-tube and a double U-tube were analyzed quantitatively through sensitivity analysis. Results indicated that, the length of the ground heat exchanger was greatly influenced by grout thermal conductivity for single U-tube and pipe spacing for double U-tube.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.281-284
• /
• 2009

Acoustic tuning frequency of quarter-wave resonators is investigated numerically to suppress combustion instability in a liquid rocket engine. A quarter-wave resonator is adopted, which was designed from the cold acoustic test for optimal damping condition. First, in a model combustion chamber scaled down from a full-scale chamber, reactive flow filed is analyzed numerically and acoustic-pressure responses are examined. Next, thermodynamic properties in the resonators are predicted. Based on the data, frequency tuning method is studied. The optimum tuning length of each resonator is proposed and thereby, sufficient damping is produced.

• Journal of Korean Society for Geospatial Information Science
• /
• v.20 no.4
• /
• pp.19-27
• /
• 2012

RUSLE(Revised Universal Soil Loss Equation) has been widely used to estimate the soil loss amount of watersheds from rainfall erosivity, soil erodibility, topographic features and cropping management condition. Rainfall erosivity is the most dominant and sensitive factor among these so that the determination of reliable rainfall erosivity is essential to estimate the soil loss of watershed. Since there has been no criterion to determine the rainfall erosivity in Korea, the empirical values, determined from the relation between the annual average rainfall and erosivity or suggested by TBR(Transport Research Board), have been used for designing the erosion control structure and controlling the soil erosion for watersheds. In this study, the procedure for estimating the rainfall erosivity using frequency analysis is proposed. The most fitted distribution function, with calculated rainfall erosivities with various frequencies and durations, has been also selected. The suggested procedure can be used to estimate the optimal value of rainfall erosivity for RUSLE in order to design soil erosion structures and control the soil erosion in watersheds effectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3135-3141
• /
• 2013

This study derives the optimal conditions for design parameters of clinch stud with high torque resistance and bonding force by using FE simulation and Taguchi method. Maximum forming load and filled rate of material are considered as objective functions. Height and depth of groove with diameter and depth of lobe are chosen as design parameters. These control factors and the friction considered as noise factor are combined by orthogonal array. Forming load and filled rate are evaluated through the simulation. Simulation results are analyzed by using the ratio of signal to noise through Taguchi method. From these results, their optimal combination conditions are proposed. In the order of the most important parameter which affects filled rate, there are the height of lobe, the height of groove, the radius of lobe and the depth of groove.

• Membrane Journal
• /
• v.30 no.5
• /
• pp.333-341
• /
• 2020

In this study, the optimum design conditions of a polymer electrolyte membrane for application to a flexible electrochromic device (ECD) were tried to be derived. Polyvinyl butyral (PVB) with excellent adhesive property and transparency was selected as the base polymer for the preparation of the electrolyte membrane, and adipate-based polymer was used as the plasticizer. As a result, it was confirmed that the most influential factors on the ECD performance were the ionic conductivity and permeability of the electrolyte membrane. In addition, it was found that the factor has a close relationship with the dissociation property of the lithium salt. Overall, the optimal ECD performance was achieved when LiTFSI salt having a large anion size among various lithium salts was dissolved in a content of about 25 wt.%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.657-663
• /
• 2018

In this study, shape optimization was performed to improve the vibration isolation capability of an anti-vibration rubber assembly, which is used in the field option cabin of agricultural tractors. A uniaxial tension test and biaxial tension test were performed to characterize the hyper-elastic material properties of rubber, and the data were used to calibrate the material model used in the finite element analyses. A field test was performed to quantify the input excitation from the tractor and the output response at the cabin frame. To account for the nonlinear behavior of rubber, static analyses were performed and the load-displacement curve of rubber was derived. The stiffness of the rubber was calculated from this curve and input to the harmonic analyses of the cabin. The results were verified using the test data. Taguchi's parameter design method was used to find the optimal shape of the anti-vibration rubber assembly, which indicated a shape with reduced stiffness. The vibration of the cabin frame was reduced by the optimization by as much as 35% compared to the initial design.