• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.55-64
• /
• 2006

This work proposes a calibration-free 14b 70MS/s 0.13um CMOS ADC for high-performance integrated systems such as WLAN and high-definition video systems simultaneously requiring high resolution, low power, and small size at high speed. The proposed ADC employs signal insensitive 3-D fully symmetric layout techniques in two MDACs for high matching accuracy without any calibration. A three-stage pipeline architecture minimizes power consumption and chip area at the target resolution and sampling rate. The input SHA with a controlled trans-conductance ratio of two amplifier stages simultaneously achieves high gain and high phase margin with gate-bootstrapped sampling switches for 14b input accuracy at the Nyquist frequency. A back-end sub-ranging flash ADC with open-loop offset cancellation and interpolation achieves 6b accuracy at 70MS/s. Low-noise current and voltage references are employed on chip with optional off-chip reference voltages. The prototype ADC implemented in a 0.13um CMOS is based on a 0.35um minimum channel length for 2.5V applications. The measured DNL and INL are within 0.65LSB and l.80LSB, respectively. The prototype ADC shows maximum SNDR and SFDR of 66dB and 81dB and a power consumption of 235mW at 70MS/s. The active die area is $3.3mm^2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.117-122
• /
• 2018

A large-capacity three-phase system air conditioner recently includes an inverter circuit to reduce power consumption. The inverter circuit uses a DC voltage that comes from DC-link power capacitor with the function of rectifying, which means AC voltage to DC voltage using a diode. An electrolytic capacitor is generally used to satisfy the voltage ripple and current ripple conditions of a DC-link power capacitor used for rectifying. Reducing the capacitance of the capacitor decreases the size, weight, and cost of the circuit. This paper proposes an algorithm to reduce the input ripple current by combining the minimum point estimation phase locked loop (PLL) phase control and the average voltage d axis current control technique. When this algorithm was used, the input ripple current decreased by almost 90%. The current ripple of the DC-link capacitor decreased due to the decrease in input ripple current. The capacitor capacity can be reduced but the electrolytic capacitor has a heat generation problem and life-time limitations because of its large equivalent series resistance (ESR). This paper proposes a method to select a film capacitor considering the current ripple at DC-link stage instead of an electrolytic capacitor. The capacitance was selected considering the voltage limitation, RMS (Root Mean Square) current capacity, and RMS current frequency analysis. A $1680{\mu}F$ electrolytic capacitor can be reduced to a $20{\mu}F$ film capacitor, which has the benefit of size, weight and cost. These results were verified by motor operation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.12 s.115
• /
• pp.1156-1163
• /
• 2006

This paper presents an ultra wideband(UWB) direct conversion mixer for IEEE 802.15.3a applications with simulation and measurement results. Since the direct conversion mixing causes dc-offset and even-order distortion, the proposed mixer adopts an anti-parallel diode pairs(APDPs) to solve these problems. The proposed mixer consists of an in-phase wilkinson power divider over $3.1{\sim}4.8GHz$, a wideband $45^{\circ}$ power divider over $1.5{\sim}2.4GHz$, and miniatured band pass filters(BPFs) for RF-LO isolations. The conversion loss is optimized with impedance matchings between APDPs and wideband components. The measured mixer shows the conversion loss of 13.5 dB, input third-order intercept-point($IIP_3$) of 7 dBm, and 1-dB gam compression point($P_{1dB}$) of -4 dBm. Quadrature(I/Q) outputs have the magnitude difference of about 1 dB and phase difference of ${\pm}3^{\circ}$.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.9
• /
• pp.2221-2234
• /
• 1997

Distributed mutual exclusion algorithms have employed two approaches to achieve mutual exclusion and can be divided into two broad classes:token-based and permission-based. Token-based algorithms share a unique token among the nodes and a node is allowed to access its common resources if it possesses the token. Permission-based algorithms require one or more successive rounds of message exchanges among the nodes to obtain the permission to access the common resources. A hypercube architecture has earned wide acceptance in multiprocessor systems in the past few years because of its simple, yet rich topology. Accordingly, we study distributed permission-based mutual exclusion algorithms for hypercubes, and design a distributed permission-based mutual exclusion algorithm based on a new information structure adapted to the hypercubes. The new information structure is a request set of T-pattern from a logical mesh that is embedded into a hypercube. If a node wants to access the common resources, it sends request message to all nodes in the request set by Lan's multicast algorithm. Once the node receives a grant message from all nodes in the request set, it accesses the common resource. We evaluate our algorithm with respect to minimum round-trip delay, blocking delay, and the number of messages per access to the common resource.

• Journal of Intelligence and Information Systems
• /
• v.16 no.3
• /
• pp.77-97
• /
• 2010

Market timing is an investment strategy which is used for obtaining excessive return from financial market. In general, detection of market timing means determining when to buy and sell to get excess return from trading. In many market timing systems, trading rules have been used as an engine to generate signals for trade. On the other hand, some researchers proposed the rough set analysis as a proper tool for market timing because it does not generate a signal for trade when the pattern of the market is uncertain by using the control function. The data for the rough set analysis should be discretized of numeric value because the rough set only accepts categorical data for analysis. Discretization searches for proper "cuts" for numeric data that determine intervals. All values that lie within each interval are transformed into same value. In general, there are four methods for data discretization in rough set analysis including equal frequency scaling, expert's knowledge-based discretization, minimum entropy scaling, and na$\ddot{i}$ve and Boolean reasoning-based discretization. Equal frequency scaling fixes a number of intervals and examines the histogram of each variable, then determines cuts so that approximately the same number of samples fall into each of the intervals. Expert's knowledge-based discretization determines cuts according to knowledge of domain experts through literature review or interview with experts. Minimum entropy scaling implements the algorithm based on recursively partitioning the value set of each variable so that a local measure of entropy is optimized. Na$\ddot{i}$ve and Booleanreasoning-based discretization searches categorical values by using Na$\ddot{i}$ve scaling the data, then finds the optimized dicretization thresholds through Boolean reasoning. Although the rough set analysis is promising for market timing, there is little research on the impact of the various data discretization methods on performance from trading using the rough set analysis. In this study, we compare stock market timing models using rough set analysis with various data discretization methods. The research data used in this study are the KOSPI 200 from May 1996 to October 1998. KOSPI 200 is the underlying index of the KOSPI 200 futures which is the first derivative instrument in the Korean stock market. The KOSPI 200 is a market value weighted index which consists of 200 stocks selected by criteria on liquidity and their status in corresponding industry including manufacturing, construction, communication, electricity and gas, distribution and services, and financing. The total number of samples is 660 trading days. In addition, this study uses popular technical indicators as independent variables. The experimental results show that the most profitable method for the training sample is the na$\ddot{i}$ve and Boolean reasoning but the expert's knowledge-based discretization is the most profitable method for the validation sample. In addition, the expert's knowledge-based discretization produced robust performance for both of training and validation sample. We also compared rough set analysis and decision tree. This study experimented C4.5 for the comparison purpose. The results show that rough set analysis with expert's knowledge-based discretization produced more profitable rules than C4.5.

• The Korean Journal of Air & Space Law and Policy
• /
• v.8
• /
• pp.231-248
• /
• 1996

이 논문(論文)은 한국(韓國)의 우주(宇宙) 산업(産業) 발달(發達)과 그 과정(過程)을 고찰(考察)하고 현재 진행 중인 통신위성(通信衛星)의 개발(開發)과 그 사업(事業)을 뒷받침해 주는 국가(國家)의 정책(政策)을 살펴보고 있다. KOREASAT라고 명명(命名)된 통신위성(通信衛星) 개발(開發)에 현재 여러 기관이 관계(關係)하고 있으나 그 중 KARI(한국항공우주연구소(韓國航空宇宙硏究所)), ETRI(전자통신연구소(電子通信硏究所)), SERI(시스템공학연구소(硏究所)), KAIST(한국과학기술연구소(韓國科學技術硏究所)) 등이 중추적인 연구(硏究)를 하고 있다. 특히 이 논문(論文)에서는 아래와 같은 문제(問題)를 다루고 있다 첫째, 최근(最近) 한국우주개발(韓國宇宙開發) 상황(狀況) 둘째, 장기(長期) 우주개발(宇宙開發) 계획(計劃) 셋째, 현재(現在) 우주개발(宇宙開發) 상황(狀況)과 미래(未來) 우주개발(宇宙開發)에 관련한 정책(政策)적 문제(問題) 넷째, 한국(韓國) 우주개발(宇宙開發)과 정책(政策) 방향(方向)에 대한 의견(意見) 최근의 한국우주개발(韓國宇宙開發) 상황(狀況)은 크게 한국(韓國)의 통신위성(通信衛星) 사업(事業)인 Koreasat program과 다목적 위성사업(衛星事業)인 KOMSAT로 나타나는데 한국(韓國)의 최초 상업용(商業用) 위성(衛星)인 Koreasat는 1호가 1995년도에 발사(發射)되었으나 정상궤도(正常軌道) 진입(進入)에 문제(問題)가 발생하여 발사업체(發射業體)로부터 보상문제(補償問題)가 제기(提起)되기도 하였으나 2호는 성공리에 발사(發射)되었다. 미국항공우주회사(美國航空宇宙會社)와 공동(共同)으로 개발(開發)중인 새로운 과학위성(科學衛星)인 KOMSAT는 한국우주과학기술(韓國宇宙科學技術)을 한단계 더 발전(發展)시킬 수 있을 것이고 1999년도에 발사(發射) 계획(計劃)이다. 한국항공우주연구소(韓國航空宇宙硏究所) 중심(中心)의 장기(長期) 우주개발(宇宙開發) 계획(計劃)에서 제시(提示)하는 4가지 우주개발(宇宙開發)의 기본목표(基本目標)는 첫째, 우주산업응용산업(宇宙産業應用産業)의 상호협조개발(相互協助開發)에 의한 우주산업(宇宙産業) 육성(育成) 둘째, 한국(韓國)의 현재 우주산업상황(宇宙産業狀況)에 알맞은 특정분야(特定分野)를 선정(選定)하고 이 분야(分野)에서 최단기에 세계(世界) 최고의 기술수준을 성취(成就)하도록 집중(集中) 셋째, 외국과 긴밀한 협조(協助)로 선진기술(先進技術)의 습득(習得) 넷째, 체계적이고 통합(統合)된 장기우주산업발전(長期宇宙産業發展) 계획(計劃) 성립(成立) 등이다. 이러한 계획(計劃)에 주요 사안(事案)으로는 2015년까지 19기의 인공위성(人工衛星) 보유(保有)를 위한 제작계획(製作計劃)과 2010년까지 발사체(發射體) 개발(開發)을 마련하는 것이다 현재 우주활동(宇宙活動)에 관련된 문제(問題)는 주로 Koreasat의 서비스와 사용계획(使用計劃)에 대한 것으로 위성개발사업(衛星開發事業)에 있어서 관련 정부부서간(政府部署間)에 의견(意見)을 달리하고 있는 형태이다. 한국통신(韓國通信)과 정보통신부(情報通信部)는 위성(衛星)의 DBS 트랜스폰더에 대해 디지털 방식(方式)을 적용(適用)할 것을 제안(提案)했지만 공보처(共報處)는 반대(反對)의 입장(立場)을 표명(表明)한 것과 방송국(放送局)의 관리(管理)와 통제(統制)는 공보처(共報處)에 있고 무선통신표준(無線通信標準)에 대한 면허(免許)는 정보통신부(情報通信部)에 있기 때문에 방송국(放送局)에 대한 면허(免許)는 각기 다른 두 단계(段階)로 구성(構成)되는 문제(問題)가 발생(發生)한다. 또한 DBS 서비스에서 사기업(私企業)의 참여(參與)와 관련하여 재벌(財閥)의 참여(參與)를 허용(許容)하느냐의 여부(與否)의 논쟁(論爭)이다. 다음으로 미래(未來) 우주산업개발(宇宙産業開發)에 관한 정책문제(政策問題)를 살펴보면 국가적(國家的) 차원(次元)에서 조직적(組織的)인 육성책(育成策)에 대한 문제(問題)로 현재 주관 부처가 과학기술처(科學技術處)와 통상산업부(通商産業部)로 나뉘어 추진(推進)되고 있다는 점이다. 그리고 차세대(次世代) 통신위성개발(通信衛星開發) 계획(計劃)에 대한 문제(問題)로 최소 2${\sim}$4개의 궤도확보(軌道確保)와 이미 정상궤도(正常軌道) 진입(進入) 실패(失敗)에 따른 Koreasat 1호의 생명단축(生命短縮)으로 새로운 통신위성(通信衛星)을 4년이내에 발사(發射)해야 한다는 문제(問題)이다. 결론적으로 장기(長期) 우주개발계획정책(宇宙開發計劃政策)에 있어서 첫째, 국제적 우주개발사업(宇宙開發事業)에 대한 적극적(積極的) 참여(參與), 둘째, 우주(宇宙)에서 독립적(獨立的)인 활동(活動)을 할 수 있는 국가안보체제(國家安保體制)의 개발(開發), 셋째, 국가(國家) 위상(位相)의 발전(發展)과 우주개발(宇宙開發)을 위한 인력활용(人力活用)의 개발(開發), 넷째, 무한한 우주(宇宙)에 도전(挑戰)할 수 있는 우수(優秀)한 인재(人才)의 교육(敎育), 다섯째, 21세기를 대비(對備)하여 한국(韓國)의 우주개발정책(宇宙開發政策)의 결정(決定) 등이 고려(考慮)되어야 할 5가지 요소(要所)들이다. 그리고 막대(莫大)한 비용(費用)이 드는 우주개발사업(宇宙開發事業)을 효율적으로 추진(推進)하기 위해서는 국가(國家) 최고(最高) 지도자(指導者)의 직접지휘(直接指揮)를 받는 정부기구(政府機構)가 수립(樹立)되어 정부차원(政府次元)에서 추진(推進)하되 산학연(産學硏)이 협조(協助)하여 우주개발계획(宇宙開發計劃)을 추진(推進)하여야 할 것으로 본다.