• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.5
• /
• pp.109-116
• /
• 2010

Infiltration and the rising level of groundwater caused by rainfall are a major cause of the landslide and sliding. In order to secure the safety factor of slope, the slope stabilization and reinforcement works are used to enhance consistency. Nailing, Slope Drainage method and the surface vegetation measures can be simultaneously applied in the Mass Nail method, which is also environmental friendly reinforcement method. To demonstrate the reinforcement effect of a strengthened slope by Mass Nail, the changes in water contents by rainfall were considered while performing Scale Model Test. As a result, safety factor of reinforced slope was about 1.4~2.3 times increased on the unstrength slope. In the case of increasing water content 10% to 22%, The maximum stress was reduced to 12%~24% at the average rate of 18% on the unstrength slope and the reinforced slope by the Mass Nail Method was reduced to 4%~23% at the average rate of 14%.

• Proceedings of the Korea Water Resources Association Conference
• /
• 1980.08a
• /
• pp.44-46
• /
• 1980

파의 에너지 감쇠기구의 관점에서 볼 때 분류손실방식인 유공벽식 방파제 중에서 원형공이 벽 전체에 균일하게 분포되어 있고 구멍 직경에 비해 벽 두께가 얇은 삼중 유공벽형 Caisson의 각 벽에 작용하는 파력에 고나해 이론적 접근과 실험을 통한 실증을 시도해 보았다. 이론적인 방법으로는 토굴구효남의 이론을 응용하였으며 주어진 파랑조건에 대해 각 유공벽 전 후면에 연속방정식과 Bernoulli 방정식을 이용하여, 각 영역별 연속 Potential의 진폭과 위상각에 대한 비선형 12원 연립방정식을 만들었고 Computer를 이용하여 반복법으로 각 속도 Potential을 확정하였다. 이렇게 구한 속도 Potential을 압력방정식에 대입하여 각 벽별 파력을 계산하였으며 동일한 파랑조건하의 실험에서 각 벽별 파력을 측정하여 양자를 서로 비교검토하였다. Bernoulli의 방정식중 에너지 손실항은 의사비선형으로 처리하였다. 유공율조합 0.25-0.3-0.2이고, 판두께가 1cm인 모형의 실험결과, 각 벽별 최대파력치의 특성으로서는 첫때, S-2, S-3등 간벽에 작용하는 파력이 전벽 및 후벽에 비해 두드러지게 작다는 사실과, 둘째 작용파력의 크기 순이 파형경사가 작을 때는 대략 S-4, S-1, S-2, S-3순이고 파형경사가 클 때에는 대략 S-1, S-4, S-2, S-3순이라는 점 등을 들 수 있겠다. 굴구효남이 가정한 f의 치 1.5를 사용하여 계산한 각 벽별 최대파력을 실험치와 비교해 본 결과, 파가 각 유공벽을 통과할 때의 손실수두를 실험에서의 양만큼 fr=1.5를 가정한 수학적 model이 설명해 주지 못한다고 볼 수 있으므로 두가지 방법에 의하여 본 실험에서 사용한 유공판의 손실계수를 근사적으로 추정하여 보았다. 추정한 f를 사용하여 다시금 각 벽별 최대파력을 계산하고 실험치와 비교해 보면 훨씬 서로 근접함을 알 수 있었다. 결국 본 논문의 이론을 사용하면 유공Caisson문제의 전체적인 윤곽 및 각 변수들의 파력에 대한 영향을 파악할 수 있겠다.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.44-51
• /
• 2016

The powder core, conventionally fabricated from iron particles coated with insulator, showed large eddy current loss under high frequency, because of small specific resistance. To overcome the eddy current loss, the increase in the specific resistance of powder cores was needed. In this study, copper oxide coating onto electrically conductive iron particles was performed using a planetary ball mill to increase the specific resistance. Coating factors were optimized by the Response surface methodology. The independent variables were the CuO mass fraction, mill revolution number, coating time, ball size, ball mass and sample mass. The response variable was the specific resistance. The optimization of six factors by the fractional factorial design indicated that CuO mass fraction, mill revolution number, and coating time were the key factors. The levels of these three factors were selected by the three-factors full factorial design and steepest ascent method. The steepest ascent method was used to approach the optimum range for maximum specific resistance. The Box-Behnken design was finally used to analyze the response surfaces of the screened factors for further optimization. The results of the Box-Behnken design showed that the CuO mass fraction and mill revolution number were the main factors affecting the efficiency of coating process. As the CuO mass fraction increased, the specific resistance increased. In contrast, the specific resistance increased with decreasing mill revolution number. The process optimization results revealed a high agreement between the experimental and the predicted data ($Adj-R^2=0.944$). The optimized CuO mass fraction, mill revolution number, and coating time were 0.4, 200 rpm, and 15 min, respectively. The measured value of the specific resistance of the coated pellet under the optimized conditions of the maximum specific resistance was $530k{\Omega}{\cdot}cm$.

• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.14-18
• /
• 1997

Using holographic interferometry, strain distributions for a cantilever beam subjected to the eccentric force can be analysed. Holographic fringe pattern shows inclined straight lines for the composite deformation of bending and torsion. Using these inclinations of the fringe pattern, 3rd order polynomial of plane displacements can be determined without difficulty. As the result, both of axial and shear strain distribution can be obtained from the second partial derivatives of this polynomial. These results agree well with FEM.

• Proceedings of the KSEG Conference
• /
• 2002.04a
• /
• pp.201-210
• /
• 2002

서울시 북동부의 서울화강암에 대한 암반 공학적 특성 중 터널과 도로 건설시 중요하게 취급되는 절리의 방향성, 절리간격, 절리밀도, 암석의 일축압축강도, 그리고 RQD 값을 수락산과 불암산지역으로 구분하여 비교, 분석하였다. 이 중 절리의 방향성, 절리간격과 절리밀도는 선조사법, 원형조사법, 그리고 면적조사법을 이용하여 야외에서 직접 측정하였다. 암석의 일축압축강도와 RQD의 측정은 시추코아의 표본이 필요하지만 이번 연구에서는 간단히 응용할 수 있는 대비공식을 이용하여 계산하였다. 측정된 대표적인 절리의 방향성은 두 지역에서 모두 3조의 방향성이 나타났으며 즉 2조의 수직정방절리와 저각으로 경사하는 1조의 판상절리로 판명되었으며 두 지역에서 서로 유사한 방향성을 갖는다. 측정된 절리밀도는 0.039-0.066/cm이었으며, 평균절리길이는 1.30-4.52m, 그리고 평균절리간격은 10.3cm에서 최대 59.6cm로 측정된 절리의 방향에 따라 변화가 심하다 또한 슈미트 해머 타격값에 근거한 절리면의 일축압축강도는 217 MPa에서 335 MPa로 매우 강한 암체였으며, 평균절리간격에 기초하여 계산된 이론적 RQD 값은 73.1-98.7%의 값을 갖는 것으로 나타났다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.1
• /
• pp.69-83
• /
• 2006

A Level 3 reliability analysis has been performed for wave run-up and overtopping on a sloping seawall. A Monte-Carlo simulation was performed considering the uncertainties of various variables affecting the wave overtopping event. The wave overtopping probability was evaluated from the individual wave run-up by using the wave-by-wave method, while the mean overtopping rate was calculated directly from the significant wave height. Using the calculated overtopping probability and mean overtopping rate, the maximum overtopping volume was also calculated on the assumption of two-parameter Weibull distribution of individual wave overtopping volume. In addition, by changing wave directions, depths, and structure slopes, their effects on wave overtopping were analyzed. It was found that, when the variability of wave directions is considered or the water depth decreases toward shore, wave height become smaller due to wave refraction, which yields smaller mean overtopping rate, overtopping probability and maximum overtopping volume. For the same mean overtopping rate, the expected overtopping probability increases and the expected maximum overtopping volume decreases as approaching toward shore inside surfzone.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.3
• /
• pp.398-404
• /
• 2020

In this paper, we propose a new design method of signal constellation of the spiral quadrature amplitude modulation (QAM) exploiting a modified gradient descent search algorithm and its binary mapping rule. Unlike the conventional method, the new method, which uses and the constellation optimization algorithm and the maximum number of iterations as a parameter for the iterative design, is more robust to phase noise. And the proposed binary mapping rule significantly reduces the average Hamming distance of the spiral constellation. As a result, the proposed spiral QAM constellation has much improved error performance compared to the conventional ones even in a very severe phase noise environment. It is, therefore, considered that the proposed QAM may be a useful modulation format for coherent optical communication systems and orthogonal frequency division multiplexing (OFDM) systems.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.169-174
• /
• 2005

In this paper, we proposed a new algorithm of the inverse scattering for the reconstruction of unknown dielectric scatterers using the finite-difference time-domain method and the design sensitivity analysis. We introduced the design sensitivity analysis based on the gradient for the fast convergence of the reconstruction. By introducing the adjoint variable method for the efficient calculation, we derived the adjoint variable equation. As an optimal algorithm we used the steepest descent method and reconstructed the dielectric targets using the iterative estimation. To verify our algorithm we will show the numerical examples for the two-dimensional $TM^2$ cases.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.6
• /
• pp.752-758
• /
• 2004

In this paper, we proposed an adaptivefuzzy sliding control algorithm using gradient descent method to reduce chattering phenomenon which is viewed in variable control system. In design of FLC, fuzzy control rules are obtained from expert's experience and intuition and it is very difficult to obtain them. We proposed an adaptive algorithm which is updated by consequence part parameter of control rules in order to reduce chattering phenomenon and simultaneously to satistfy the sliding mode condition. The proposed algorithm has the characteristics which are viewed in conventional VSC, e.g. insensitivity to a class of disturbance, parameter variations and uncertainties in the sliding mode. To demonstrate its performance, the proposed control algorithm is applied to an inverted pendulum system. The results show that both alleviation of chattering and performance are achieved.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.363-368
• /
• 2003

We have successfully developed a more effective algorithm to extract the lineament in the area covered by wide alluvial deposits characterized by a relatively narrow range of brightness in the Landsat TM image, while the currently used algorithm is limited to the mountainous areas. In the new algorithm, flat areas mainly consisting of alluvial deposits were selected using the Local Enhancement from the Digital Elevation Model (DEM). The aspect values were obtained by 3${\times}$3 moving windowing of Zevenbergen & Thorno's Method, and then the slopes of the study area were determined using the aspect values. After the lineament factors in the alluvial deposits were revealed by comparing the threshold values, the first rank lineament under the alluvial deposits were extracted using the Hough transform In order to extract the final lineament, the lowest points under the alluvial deposits in a given topographic section perpendicular to the first rank lineament were determined through the spline interpolation, and then the final lineament were chosen through Hough transform using the lowest points. The algorithm developed in this study enables us to observe a clearer lineament in the areas covered by much larger alluvial deposits compared with the results extracted using the conventional existing algorithm. There exists, however, some differences between the first rank lineament, obtained using the aspect and the slope, and the final lineament. This study shows that the new algorithm more effectively extracts the lineament in the area covered with wide alluvlal deposits than in the areas of converging slope, areas with narrow alluvial deposits or valleys.