• Clean Technology
• /
• v.24 no.4
• /
• pp.332-338
• /
• 2018

Currently graphite is used as an anode active material for lithium ion battery. However, since the maximum theoretical capacity of graphite is limited to $372mA\;h\;g^{-1}$, a new anode active material is required for the development of next generation high capacity and high energy density lithium ion battery. The maximum theoretical capacity of Si is $4200mA\;h\;g^{-1}$, which is about 10 times higher than the maximum theoretical capacity of graphite. However, since the volume expansion rate is almost 400%, the irreversible capacity increases as the cycle progresses and the discharge capacity relative to the charge is remarkably reduced. In order to solve these problems, it is possible to control the particle size of the Si anode active material to reduce the mechanical stress and the volume change of the reaction phase, thereby improving the cycle characteristics. Therefore, in order to minimize the decrease of the charge / discharge capacity according to the volume expansion rate of the Si particles, the improvement of the cycle characteristics was carried out by pulverizing Si by a dry method with excellent processing time and cost. In this paper, Si is controlled to nano size using vibrating mill and the physicochemical and electrochemical characteristics of the material are measured according to experimental variables.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.112-118
• /
• 2001

Magnetic field is commonly used in low temperature processing plasmas to enhance the performance of the plasma reactors. E$\times$B magnetron or surface multipole configuration is the most popular. However, the properties of capacitively coupled rf plasma confined by axial static magnetic field have rarely been studied. With these background, the effect of magnetic field on the characteristics of capacitively coupled 13.56 MHz/40 KHz argon plasma was studied, Ion saturation current, electron temperature and plasma potential were measured by Langmuir probe and emissive probe. At low pressure region (~10 mTorr), ion current increases by a factor of 3-4 due to reduction of diffusion loss of charged particles to the wall. Electron temperature slightly increases with magnetic field for 13.56 MHz discharge. However, for 40 KHz discharge, electron temperature decreased from 1.8 eV to 0.8 eV with magnetic field. It was observed that the magnetic field induces large temporal variation of the plasma potential. Particle in cell simulation was performed to examine the behaviors of the space potential. Experimental and simulation results agreed qualitatively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.3
• /
• pp.48-54
• /
• 2015

In this study, we propose an innovative lateral force distribution building system between tall buildings by utilizing the difference of moment of inertia, resulting the reduction of lateral displacement and the lateral forces in terms of an alternative for the dense human and increased cost of lands in highly integrated city area. A successive collapse prevention means by providing additional bearing plate between connections is proposed. In addition to that, a more economical vibration reduction is expected due to the suggested tuned mass damper on the surface of spacial structure. In the considered verification examples, reduced drifts at the top location of the building systems are validated against static wind pressure loads and static earthquake loads. The suggested hybrid building system will improve the safety and reliability of the new or existing building system in terms of more than 30% reduced drift and vibration through the development of convergence of tall buildings and spatial structures.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.2
• /
• pp.37-43
• /
• 2008

The performance and hardware complexity of LDPC decoders depend on the design parameters of quantization, the clipping threshold $c_{th}$ and the number of quantization bits q, and also on the maximum number of decoding iterations. In this paper, the BER performances of LDPC codes are evaluated according to the clipping threshold $c_{th}$ and the number of quantization bits q through the simulation studies. By comparing the quantized Min-Sum algorithm with the ideal Min-Sum algorithm, it is shown that the quantized case with $c_{th}=2.5$ and q=6 has the best performance, which approaches the idea case. The decoding complexities are calculated and the word error rates(WER) are estimated by using the pdf which is obtained through the statistical analyses on the iteration numbers. These results can be utilized to tradeoff between the decoding performance and the complexity in LDPC decoder design.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.707-713
• /
• 1998

The influence of plasma carburizing process on the surface hardness of SCM415 low-alloy steel (0.15% C) was investigated under the various process conditions of gas composition. gas pressure, plasma current density. temperature and time. The effective case depth was found to depend on the amount of methan gas containing carbon. thus the deepest case depth and the uniform hardeness were obtained with the 100% methan gas. The case depth increased with the plasma current density. The effective plasma carburizing temperature of SCM415 steel was found to be higher than 85$0^{\circ}C$, and the case depth was proportional to the square root of carburizing time under the same current density. The bending fatigue strength of the plasma carburized specimen is' higher than those of as- received specimen or reheat-quenched specimen.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.587-587
• /
• 2012

현재 대부분 하천관리의 흐름해석에서 주가 되었던 1차원 분석은 하천 단면에 따른 횡적인 수면차, 유속분포를 분석할 수 없다는 단점을 가지고 있으며, 특히 유량 및 유속이 급속도로 늘어나는 홍수시에는 그 오차가 더욱 커질 수 있다. 반면에 2차원 모형의 흐름해석은 사행하천의 흐름 특성과 만곡부에서의 종 횡방향 수면경사 및 양안의 수면차와 합류지점의 횡방향 흐름 등의 영향을 고려할 수 있으며 1차원 해석과는 달리 전 단면에 걸쳐 유속 및 수위 분포를 나타낼 수 있어 실제흐름에 가까운 수리량을 얻을 수 있다. 본 연구를 위해 적용된 해석모형인 SMS는 미국 Brigham Young 대학의 환경모형연구실과 미공병단(USACE)의 수로실험국(WES) 등에서 개발한 프로그램으로서 RMA2, RMA4, SED2D 모형 등으로 구성되어 있다. 각각의 모형은 수리 동역학적 해석, 오염물 이송확산 해석, 유사의 이송 및 퇴적 해석이 가능하며 이 중 RMA2를 이용한 2차원 흐름해석을 통하여 보다 적합한 하천관리에 이용가능하도록 하고자 한다. 연구대상 지역은 제주도 한천 하류부로서 제주도 하천 특성상 평상시 건천의 상태를 이루고 있으나 태풍 및 집중호우시 홍수유출이 발생하여 수위가 급격하게 상승하는 양상을 보인다. 대표적인 예로 태풍 '나리'시 최대 일강우량 420mm로 인한 인근 지역에 0.5 ~ 1.5m의 침수흔적을 보이고 있다. 본 연구에서는 2011년 최고수위를 기록한 태풍 '무이파'를 대상으로 하였으며 대상지역의 Kalesto를 이용한 수위-유속 자료를 이용하여 산출된 유량을 경계조건으로 사용하였고 격자망 형성을 위한 지형 데이터는 지형도 및 측량자료를 이용하여 구축하였다. 사용된 대표적인 매개변수는 하상의 조도계수를 나타내는 Manning의 n값과 유체의 밀도, 속도구배, 구조 등 여러 가지의 유체조건에 따라 변하는 성질인 와점성계수(eddy viscosity)로 요약할 수 있으며 Manning의 n값은 하천설계기준에 따른 하천기본계획의 조도계수를 사용하였고 와점성계수는 적합한 흐름 분포를 결정하기 위해 흐름이 안정될 때까지 변화시켜 해석을 시행하였다. 해석결과 만곡부에서는 급한 흐름을 보이고 있으며 최대하폭 구간에서는 완만한 흐름이 나타나 사행하천의 흐름특성과 횡적인 하천단면에 따른 변화, 하상고 차이로 인한 유속분포를 확인할 수 있으며 이는 보다 유용한 하천관리에 이용가능할 것으로 사료된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1860-1864
• /
• 2006

본 연구는 강우시 발생되는 강우유출수와 합류식하수관거월류수에 의해 하천으로 유입되는 오염부하를 저감시키기 위한 공법으로, 고수부지 및 제방사면부와 둔치부를 형상화하여 pilot를 제작하였고, 연속적으로 시운전을 한 SRTS(Stormwater Runoff Treatment System)에 관한 것이다. SRT system 내부의 사면수처리부와 평면수처리부에는 다공성 콘크리트를 충진하였다. system 상부에는 식생을 조성하여 뿌리가 수면에 닿아 영양물질을 흡수하는 목적으로 사면수처리부와 평면수처리부에 각각 정육각형과 직사각형인 식생포트를 탈.부착이 가능하도록 고안하였다. 내부에서는 토양과 수처리조 사이에 연결관을 부착하였고, 모세관현상에 의해 토양이 수분을 흡수하도록 구성하였다. pilot plant는 유입부, 사면 수처리부, 평면 수처리부, 유출부로 나누었다. 유입부는 유입펌프와 V-notch로 구성하였고, 유입펌프는 2대를 설치하여 1시간 간격으로 연속적 유입으로 유량조절이 가능하도록 상호교대 운전을 하였다. 평면 수처리부$(W(1.0m){\times}(L(2.4m){\times}H(0.6m))$는 장방형의 접촉산화조로서 하부에 슬러지 침전 및 저류를 위한 hopper를 설치하여 슬러지의 원활한 수집 및 인발이 가능하도록 하였다. 유출부는 사각weir를 설치하였다. 강우유출수의 pH는 $7.27{\sim}7.92$이고, DO농도는 $7.12{\sim}7.88mg/l$로 관측되었다. 2차처리수의 pH는 평균7.4이고 DO농도는 최저 4.5 mg/l에서 최고 8.9 mg/l로 평균 6.8 mg/l로 관측되었다. 또한 강우유출수의 유입수의 T-N, T-P 농도는 각각 $17.5{\sim}22.5mg/l,\;8.9{\sim}11.4mg/l$의 범위이고, 2차 처리수의 유입수의 T-N, T-P 농도와 유사하였다.적인 방법론을 제시할 수 있을 것으로 사료된다.첨두홍수량을 저류하기 위해서 상대적으로 넓은 저류면적이 필요한 것으로 나타난다. 대등한 수위감소값의 홍수저감효과를 발휘하기 위해서 본 연구에서는 On-Line 저류지 면적은 Off-Line 저류지에 비 두배 이상이 필요한 것으로 보여졌다.들에 관한 정보는 종종 현장관측에서 조차 무시되는 경우가 많다. 이에 본 연구에서는 수질모형의 매개변수 중 특히 수리특성에 관련된 매개변수들이 수질에 미치는 영향을 파악하는 것을 목적으로 하고 있다. 이를 위해 적용된 수질모형은 QualKo를 사용하였으며, 대상 하천은 낙동강 본류 경남구간 시점 부근인 회천 합류 전부터 낙동강 본류 경남구간 종점 부근인 밀양강 합류 전까지의 경남 오염총량관리 기본계획 시 구축된 모형 매개변수를 바탕으로 분석을 수행하였다. 일차오차분석을 이용하여 수리매개변수와 수질매개변수의 수질항목별 상대적 기여도를 파악해 본 결과, 수리매개변수는 DO, BOD, 유기질소, 유기인 모든 항목에 일정 정도의 상대적 기여도를 가지고 있는 것을 알 수 있었다. 이로부터 수질 모형의 적용 시 수리 매개변수 또한 수질 매개변수의 추정 시와 같이 보다 세심한 주의를 기울여 추정할 필요가 있을 것으로 판단된다.변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략을 활용하는 경우 주식투자기간은 24개월이하의 중단기가 적합함을 발견하였다. 이상의 행태적 측면과 투자성과측면의 실증결과를 통하여 한국주식시장에 있어서 시장수익률을 평균적으로 초과할 수 있는 거래전략은 존재하므로 이러한 전략을 개발 및 활용할 수 있으며, 특히, 한국주식시장에 적합한 거래전략은 반전거래전략이고, 이 전략의 유용성은 투자자가 설정한 투자기간보다 더욱 긴 분석기간의 주식가격정보에 의하여 최대한 발휘될 수 있음을 확인하

• Korean Journal of Food Science and Technology
• /
• v.45 no.4
• /
• pp.441-450
• /
• 2013

The purpose of this study was optimization of the conditions for mixing different amounts of red radish (Raphanus sativus L.) sprout powder, butter, and sugar when baking domestic wheat cookies prepared using red radish sprout powder. Response surface methodology, with a central composite design comprising 5 levels and 3 variables, was used to identify the best possible combination of amounts of red radish sprout powder ($X_1$), butter ($X_2$), and sugar ($X_3$). The physical and mechanical properties of each of the 20 samples analyzed, including color L (p<0.001), color a (p<0.01), color b (p<0.001), spread ratio (p<0.001), and hardness (p<0.01), differed significantly. The results of sensory evaluations, including color (p<0.001), appearance (p<0.001), texture (p<0.001), flavor (p<0.01), taste (p<0.001), and overall quality (p<0.001) also differed significantly among the samples. The optimal compositional ratios were 5.15 g for the red radish sprout powder, 64.84 g for the butter, and 47.18 g for the sugar.

• Journal of Korean Society of Forest Science
• /
• v.78 no.3
• /
• pp.314-322
• /
• 1989

For the improvement of nursery condition and the study of eco-physiological characteristics of Pinus koraiensis(2-2) seedlings, the primary productivity was investigated and the growth characteristics and their correlationship were analyzed from May to September in 1987. Seedlings used in this study were grown at the nursery of Experimental Forestry of Kyung Hee Univ. The installation of experimental plots were divided into control plot (100%), 63%, 37% and 19% relative light intensity, and each relative light intensity plots were split into $15{\times}15/m^2$, $12{\times}12/m^2$, $9{\times}9/m^2$ and $6{\times}6/m^2$ plnting density by randomized black design method. To take into account the edge effect of plant population, material were selected from each plot by random sampling at 30 days interval. Each sampled material was divided into leaf and stem drived in a drying oven at the temperature of $85^{\circ}C$ until it had constant weight and weighed. and leaf area was surveyed. Growth analysis for RGR and NAR was done by Blackman method and correlation coefficient were investigated between RGR and NAR by analyzing the dry matter production and growth characteristics of the material, cultivated on the experimental nursery under the condition of different treatment the obtained result were as follows : 1. The increasing rate of dry matter was similar at early stage of growth, but not at late stage. 2. Leaf area growth was the maximum value at 63% relative light intensity and the minimum at 19% RLI 3. The value of RGR was the highest on June under $6{\times}6/m^2$ planting density in 63% relative light intensity, the lowest on September under $12{\times}12/m^2$ of 19% relative light intensity. 4. The change NAR decreased in early stage of growth, while it increased on August and September, The value of RGR on June under $6{\times}6/m^2$ planting density in 100 light intensity was the highest, and on September under $12{\times}12/m^2$ planting density in 19% relative light intensity was the lowest. 5. Regression and correlation between RGR and NAR showed significantly positive.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.109-123
• /
• 2009

The aim of the study was to assess the influence of insertion torque of bone quality and to compare axial force, moment and von Mises stress using finite element analysis of plastoelastic property for bone stress and strain by dividing bone quality to its thickness of cortical bone, density of trabecular bone and existence of lower cortical bone when implant inserted to mandibular premolar region. The $Br{\aa}nemark$ MKIII. RP implant and cylindrical bone finite model were designed as cortical bone at upper border and trabecular bone below the cortical bone. 7 models were made according to thickness of cortical bone, density of trabecular bone and bicortical anchorage and von Mises stress, axial force and moment were compared by running time. Dividing the insertion time, it seemed 300msec that inferior border of implant flange impinged the upper border of bone, 550msec that implant flange placed in middle of upper border and 800msec that superior border of implant flange was at the same level as bone surface. The maximum axial force peak was at about 500msec, and maximum moment peak was at about 800msec. The correlation of von Mises stress distribution was seen at both peak level. The following findings were appeared by the study which compared the axial force by its each area. The axial force was measured highest when $Br{\aa}nemark$ MKIII implant flange inserts the cortical bone. And maximal moment was measured highest after axial force suddenly decreased when the flange impinged at upper border and the concentration of von Mises stress distribution was at the same site. When implant was placed, the axial force and moment was measured high as the cortical bone got thicker and the force concentrated at the cortical bone site. The influence of density in trabecular bone to axial force was less when cortical bone was 1.5 mm thick but it might be more affected when the thickness was 0.5 mm. The total axial force with bicortical anchorage, was similar when upper border thickness was the same. But at the lower border the axial force of bicortical model was higher than that of monocortical model. Within the limitation of this FEA study, the insertion torque was most affected by the thickness of cortical bone when it was placed the $Br{\aa}nemark$ MKIII implant in premolar region of mandible.