• Journal of the Korea Concrete Institute
• /
• v.22 no.5
• /
• pp.711-718
• /
• 2010

The requirement of the maximum yield strength of shear reinforcement in the KCI-07 code is quite different to those in the ACI-08 code, EC2-02, CSA-04, and JSCE-04 codes. Eighteen RC beams having high strength shear reinforcement were tested. Test results indicated that even if the yield strength of shear reinforcement in beams was much greater than the maximum yield strength required by the KCI-07 design code, the shear reinforcement of these beams reached their yield strains. Furthermore, the shear strengths of tested beams increased almost linearly with the increase of the amount of shear reinforcement. In addition, larger numbers of diagonal cracks developed in the web of the beam having greater yield strength than the beams having lower yield strength of shear reinforcement. The maximum crack width of the beam having high strength shear reinforcement was approximately the same to the crack with of the beam having normal strength shear reinforcement.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.85-85
• /
• 2017

무동력 복합작업기는 치즐쟁기와 디스크의 배열에 따라 작업성능이 좌우된다. 프레임과 디스크, 치즐쟁기에 가해지는 기본적인 힘의 상태를 확인하기 위한 정적 구조해석을 수행하였다. 복합작업기는 디스크는 $18^{\circ}$가 경사진 형태로 전면9개 후면9로 총 18개, 치즐쟁기(Chiselplow)는 4개로, 디스크는 모두 18개이다. 정적인 상태에서 끄는 견인력은 100마력, 150마력, 200마력으로 하였으며 Inventor의 해석 시스템은 힘을 N으로 사용하기 때문에 각 마력에 부가되는 하중을 N으로 치환하여 사용하였다. 구속조건은 frame과, disc, chisel plow에 맞닿는 면을 구속하고, 힘의 방향은 프레임과 트랙터의 연결면, 디스크 날과 땅의 접촉면에 적용했다. front /rear 디스크는 이론상으로는 양 디스크가 쌍으로 마주하고 있어서 스캔데이타를 중심으로 모델링한 결과를 바탕으로, 전후면 디스크해로우의 해석을 수행하였다. 조립 또는 사용상의 문제점이나 자연적인 유격에 의해 어느 정도 대칭이 되지 않을수 있으나 그 정도에 따라 진동과 내구성에 문제가 될 수도 있기에 한쌍에 대해 모델링을 통한 해석을 수행하였다. 해석결과에 따르면 디스크에 작용하는 폰미세스 응력은 극한강도에 미치지 않은 것으로 나타났으며 Frame의 최대 폰 미세스 응력을 제외하면, 대부분의 응력은 항복강도에 현저히 미치지 못하는 수치이고, 프레임의 경우는 150마력, 200마력으로 힘을 가할 때 항복강도는 넘는 수치이지만 극한인장강도에는 미치지 못하는 수치인 것을 알 수 있었다. 100마력에 폰 미세스 응력의 최대값은 0.161918 MPa이고 프레임 강의 항복강도인 207MPa와 디스크의 항복강도인 250MPa에 못 미치는 수치이다. 150마력과 200마력의 힘으로 회전할 때의 폰 미세스 응력의 최대값은 0.286425MPa과 0.381921 MPa로 항복강도인 250MPa에 크게 못 미치는 수치이다. 그 이유는 디스크해로우 방식의 복합작업기는 견인저항력이 작게 설계되고 작업속도를 개선하기 위한 목적으로 사용되기 때문으로 사료된다. 벤치마킹 기대의 Rear 디스크도 마찬가지로 각도는 $18^{\circ}$이며, 동일한 구속조건을 적용하여 시뮬레이션을 수행하였으며 해석결과는 모두 항복강도 이내로 예측 되었다. 디스크에 최대로 응력이 미치는 부분은 디스크와 프레임이 연결되는 허브 부분이다. 각도가 커짐에 따라 응력이 증가하므로 이를 감안한 설계인자 도출이 가능하다. 마력과 각도가 증가함에 따라 디스크 해로우에 작용하는 폰미세스 응력과, 접촉압력이 증가하므로 이에 대한 검토와 동적하중인 로드프로파일을 적용한 해석을 수행하여 내구수명 특성에 대한 연구를 수행할 계획이다.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.33-42
• /
• 2004

Making use of SN steel in the building structure should be a prerequisite to adopt the design strength of said steel. As a preceding study, the material properties of STKN400B/490B tubes and SPAP235/325 and SPAR295 square pipes manufactured using SN400B/490B plates were evaluated. Compared with the yield and ultimate strengths of SN400B/490B plates, those of STKN400B/490B tubes increase. Nonetheless, the yield and ultimate strengths of STKN400B/490B tubes satisfied the design codes of STKN400B/490B tubes even though the tubes were fabricated via roll bending or press forming. On the other hand, the yield and ultimate strengths at the edges of SPAP235/325 square pipes did not satisfy the design codes based on the values at the sides. The maximum tensile and compressive residual stresses at the SN490B tube were equal to and 40% of the yield strength of the SN490B plate, respectively, In the case of the SPAP325 square pipe, both the maximum tensile and compressive residual stresses were 80% of the yield strength of the SN490B plate. The axial compressive loaded column test results snowed that the buckling strengths were not very different regardless of the mode of fabrication of STKN490B tunes. i.e., through roll bending or press forming. On the other hand, the buckling strength of the SPAP325 square pipe was higher than that of the built-up square pipe.

• Journal of the Korea Concrete Institute
• /
• v.28 no.1
• /
• pp.33-40
• /
• 2016

The KCI-12 and ACI 318-14 design codes limit the maximum yield strength of shear reinforcement to prevent concrete compressive crushing before the yielding of shear reinforcement. The maximum yield strength of shear reinforcement is limited to 420 MPa in the ACI 318-14 design code, while limited to 500 MPa in the KCI-12 design code. A total of eight post-tensioning prestressed concrete beams with high strength shear reinforcement were tested to observe the shear behavior of PSC beams and the applicability of the high strength reinforcement was thus assessed. In the all PSC beam specimens that used stirrups greater than maximum yield strength of shear reinforcement required by the ACI 318-14 design code, the shear reinforcement reached their yield strains. The observed shear strength of tested eight PSC beams was greater than the calculated ones by the KCI-12 design codes. In addition, the diagonal crack width of all specimens at the service load was smaller than the crack width required by the ACI 224 committee. The experimental and analytical results indicate that the limitation on the yield strength of shear reinforcement in the ACI 318-14 design code is somewhat under-estimated and needs to be increased for high strength concrete. Also the application of high strength materials to PSC is available with respect to strength and serviceability.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.466-475
• /
• 2001

The potential shear strength of reinforced concrete beams decreases after flexural yielding due to the decrease of the effective compressive strength of concrete in plastic hinge zone. A truss model considering shear deterioration in the plastic hinge zone was proposed in order to evaluate the ductile capacity of reinforced concrete beams failing in shear after flexural yielding This model can determine the potential shear strength of the beam by using a truss model. The potential shear strength gradually decreases as the increase of the axial strain of member. When the calculated potential shear strength decreases up to the flexural yielding strength, the corresponding rotation angle is defined as the ductile capacity of the beam. The predicted ductile capacity of reinforced concrete beams is shown to be in a good agreement with experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1068-1073
• /
• 2010

A welding neck flange is widely used for an interconnection between pipes. It is produced by a hot forging process, and required high yield strength under the high pressure condition, like a deep-sea. Generally, to increase yield strength, a increasing of carbon content is used, however a carbon content of welding neck flange is limited to 0.47. So, in this study, a strengthening by grain refinement without changing carbon content is used to increase yield strength. Taguchi method and FEM are used for the optimization of forging process and the experiment for the yield strength of the prototype with the optimal forging process is performed for validity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4216-4222
• /
• 2011

In this study the inelastic behavior of the existing school buildings with infilled masonry walls is analysed by pushover method. The shear stiffness and strength of masonry wall is calculated from the prior experimets and verified by inelastic analysis. The height of infilled masonry wall affects the structural behavior. The higher the masonry wall height, the higher the initial shear stiffness and strength of masonry wall. As the cracks are developed, the strength of masonry wall is much decreased. The proposed inelastic analysis method shows similar results with the experiments and can be used as inelastic analysis model of reinforced concrete buildings with infilled masonry walls.

• Magazine of the Korea Concrete Institute
• /
• v.7 no.2
• /
• pp.146-154
• /
• 1995

I n this paper, an experimental research was carried out to investigate the confinement effect of spiral reinforcements in concrete column specimens subjected to t.he concentric axial corn pressive loads. Main variables were the compressive strengths of concrete of 27.2, 62.4 and 81.2 MPa, and the spacings of spirals of 120, 60, 40, 30, 25 and 20mm. and the yield strengths of spir als of 451 and 1375MPa, respectively. For the same volumetric ratio and yield strength of spir als, it was shown that the strength increment of confined concrete was almost same regardless of the strength of unconfined concrete, however, the axial stram at maximum stress was decreas ed with increasing of the compressive strength of unconfined concrete.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.2
• /
• pp.125-130
• /
• 2008

A spherical indentation has been proposed as a nondestructive method of measuring local residual stress field in laser-voided joints. The apparent yield strengths interpreted from the spherical indentation data of as-welded cutting wheel were compared with the intrinsic yield strengths measured at nearly equivalent locations in annealed wheel. Their difference along the distance from the welding line is welding stress distribution because the intrinsic yield strength is invariant regardless of the elastic residual stress. The spherical indentations show that the laser-welded diamond cutting wheel displays a 10 min-wide distribution of the welding residual stress and has peak compressive and tensile stresses in the shank and tip regions, respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1992.03a
• /
• pp.47-58
• /
• 1992

탄소성 재료의 파괴에서 최대하중을 계산할 수 있는 방법이 제시되었다. 사용된 재 료상수는 파괴개시인성, 항복강도, 진행된 균열선단에서 열림 변위 증분에 대한 균열성장의 비이고, 계산을 실험결과에 맞추어 재료상수를 결정한다. 이들 상수로 다른 시편의 최대하 중을 계산하는 간단한 방법을 평면변형하의 A572 강(상온)과 4533(B)강(-10C)에 적용하여 기존의 실험결과와 비교하였다. 또한 균열 선단 열림 변위와 J-적분값에 기초한 다른 방법 과 비교·논의되었다.