• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.157-166
• /
• 2022

Structural supervision on the construction site has been performed based on visual inspection, which is highly labor-intensive and subjective. In this study, the remote technique was developed to improve the efficiency of the measurements on rebar spacing using a 360° camera and reconstructed 3D models. The proposed method was verified by measuring the spacings in reinforced concrete structure, where the twelve locations in the construction site (265 m²) were scanned within 20 seconds per location and a total of 15 minutes was taken. SLAM, consisting of SIFT, RANSAC, and General framework graph optimization algorithms, produces RGB-based 3D and 3D point cloud models, respectively. The minimum resolution of the 3D point cloud was 0.1mm while that of the RGB-based 3D model was 10 mm. Based on the results from both 3D models, the measurement error was from 10.8% to 0.3% in the 3D point cloud and from 28.4% to 3.1% in the RGB-based 3D model. The results demonstrate that the proposed method has great potential for remote structural supervision with respect to its accuracy and objectivity.

• Journal of Oral Medicine and Pain
• /
• v.30 no.3
• /
• pp.375-381
• /
• 2005

Er:YAG laser has been considered a promising alternative to dental drill and many researches indicate that adjustment to variable parameters, including water flow rate, pulse energy and pulse repetition rate, can be made to improve ablation ability and efficiency of the laser. Of these parameters, addition of water spray during irradiation has been thought to ablate dental hard tissue more rapidly and safely. The purpose of this study was to investigate tooth ablation amount by Er:YAG laser irradiation as related to varied water flow rates added and, ultimately to find the most effective water flow rate for ablation. In addition, the temperature change of pulp chamber during irradiation was also monitored on the irradiated and opposite pulpal walls, respectively. An Er:YAG laser with contact mode was employed. Extracted human molars were split into two pieces for ablation experiment. Pulse energies of 200 and 300 mJ with a pulse repetition rate of 20 Hz and 5 water flow rates (1.6, 3.0, 5.0, 7.0, and 10.0 ml/min) were applied. Each irradiation was performed for 3 seconds. According to these parameters, experimental groups were divided into 10 subgroups which consisted of 5 specimens. For temperature experiment, another 5 tooth-specimens were prepared in the manner that pulp chamber was open through access cavity preparation and two temperature-measuring probes were placed respectively on the irradiated and the opposite walls of pulp chamber. From the experiment on ablation amount related to different water flow rates, it was shown that the least water flow rate of 1.6 ml/min ablated more than any other water flow rates (p<0.000). When the irradiation for 3 seconds, combined with the pulse repetition time of 20Hz and the water flow rate of 1.6 ml/min was done to tooth specimen, the temperature rise was not noticeable both on the irradiated and the opposite pulpal walls (less than 3$^{\circ}C$) and there was no significant difference in temperature rise between the two pulse energies, 200 and 300 mJ. From the results of this study, it is suggested that tooth ablation with Er:YAG laser can be done effectively and safely at a energy between 200 and 300 mJ/pulse and a pulse repetition rate of 20 Hz when the lasing is conjugated with the water flow rate of 1.6ml/min.

• Journal of Aquaculture
• /
• v.19 no.4
• /
• pp.281-287
• /
• 2006

Intraspecific diploid androgenesis was achieved in mud loach (Misgurnus mizolepis) by the inhibition of the first mitotic division using combined thermal treatment. A combined thermal treatment (heat shock at $40.5\;^{\circ}C$ for 120 sec followed by cold treatment at $1\;^{\circ}C$ for 45 min) applied to the 1st metaphase of cell division (28 min post insemination at $25\;^{\circ}C$) successfully recovered viable androgenetic diploidy. Mean hatching success of the androgenetic diploid group was 29.6%, and the average yield out of total eggs taken was about 7% assessed at 1 week of age. However, relatively large variations in the yield of diploid androgenesis were observed among different egg batches used as cytoplasmic donors. Successful diploidization was confirmed by flow cytometric analysis, and parthenogenic reproduction in a paternal exclusive manner was verified with transgene dosage. Significant mortality was found in most androgenetic groups especially from hatch to 1 month of age, although such mortality was stabilized later.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.41 no.2
• /
• pp.152-156
• /
• 2014

The purpose of this study is to compare efficiency of broad spectrum LEDs ($VALO^{(R)}$, Ultradent, USA) with conventional LED curing lights ($Elipar^{TM}$ Freelight 2, 3M ESPE, USA) using a microhardness test. The light curing units used were $VALO^{(R)}$ in three different modes and $Elipar^{TM}$ Freelight 2. The exposure time was used according to the manufacturer's instructions. After cured resin specimens were stored in physiological saline at $37^{\circ}C$ for 24 hours, microhardness was measured using Vickers microhardness tester. The microhardness of upper and lower sides of the specimens were analyzed separately by the ANOVA method (Analysis of Variance) with a significance level set at 5%. At upper side of resin specimens, an increased microhardness was observed in the broad spectrum LED curing light unit with a high power mode for 4 seconds and plasma emulation mode for 20 seconds (p < 0.05). However, at the lower side of resin specimens, there were no significant differences in microhardness between broad spectrum LED curing light unit and conventional LED curing light unit.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.16-22
• /
• 2020

The Korea Institute of Ocean Science & Technology is developing a free-fall cone penetration test system (FFCPT) that can acquire the characteristics of the seabed surface soil. To obtain the data through the FFCPT, a method of storing the signals for the entire time or a method of storing the signal for user-defined time can be considered. For efficient data storage and management, it is advantageous that data be stored by user definition. Therefore, this study analyzed the basic behavior using the signal acquired through a sensor mounted in the FFCPT and developed a trigger method to recognize the start and end of data storage using a depth sensor. The start and endpoints of the fall were determined using the moving average difference of 3 and 0.03 seconds of the depth signal. A real sea-trial test was performed using the FFCPT, and the developed trigger was operated normally.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.414.1-414.1
• /
• 2016

스크린 프린팅법을 이용한 태양전지의 전극은 주로 고가의 은을 사용하기에 태양전지의 저가화에 한계를 가지고 있다. 고효율 결정질 실리콘 태양전지의 원가절감의 문제 해결방안으로 박형 웨이퍼 연구개발이 많은 관심을 받고 있다. 본 연구에서는 은 전극을 대체 할 수 있는 니켈/구리 전극을 사용하였고, 박형 웨이퍼에서도 전극 공정이 가능한 도금법을 사용하여 전극을 형성 하였다. 니켈 전극형성은 광유도 도금법(Light-Induced Plating), 구리 전극형성은 광유도전해도금법(Light-Induced Electro Plating)을 이용하여 실험을 진행 하였다. 니켈 광유도 도금 공정시 공정시간 3 ~ 9분까지 가변하였다. 니켈실리사이드 형성 위해 열처리 공정을 $300{\sim}450^{\circ}C$까지 가변하였고 유지시간 30초 ~ 3분까지 가변하여 실험을 진행하였다. 니켈 도금 수용액의 pH 6 ~ 7.5까지 가변하여 실험하였다. 구리 광유도 전해도금 공정 전류밀도를 $1.6mA/cm^2{\sim}6.4mA/cm^2$까지 가변하여 실험을 진행 후, 전류밀도 $3.2mA/cm^2$로 시간 5 ~ 7분까지 가변하여 실험 하였다. 니켈 도금 공정 시간 5분, 니켈실리사이드 형성 열처리 온도 $350^{\circ}C$, 유지시간 1분에서 DIV(Dark I-V) 분석결과 가장 적은 누설전류를 확인하였다. 니켈 도금액 pH 6.5에서 니켈입자 및 구리입자의 균일성이 좋은 최적의 조건임을 확인하였다. 구리 도금 공정 전류밀도 $3.2mA/cm^2$, 시간 5분에서 TLM(Transmission Line Method) 측정결과 접촉 저항 $0.39{\Omega}$과 접촉 비저항 $12.3{\mu}{\Omega}{\cdot}cm^2$의 저항을 확인하였다. 도금법을 이용하여 전극을 형성함으로써 접촉저항 및 접촉 비저항이 낮고 전극 품질이 향상됨으로서 셀의 전류밀도 $42.49mA/cm^2$를 얻을 수 있었다.

• 한국정보교육학회:학술대회논문집
• /
• 2005.08a
• /
• pp.314-321
• /
• 2005

교육정보화 사업은 제 1, 2단계 교육정보화 종합발전 방안의 큰 틀 안에서 성공적으로 추진되어 왔다. 제 1단계 교육정보화 종합 계획에서 물적 기반 구축을 중심으로 이루어지던 교육정보화 정책이 2001년부터 시행된 제 2단계 교육정보화 종합 발전 방안에서는 활용 중심의 교육정보화 방향으로 전환하여 수행되어 왔다. 제 2단계 교육정보화 종합 발전방안이 종료되는 2005년 현 시점에서 돌이켜 보면, 교육정보화 인프라 구축 및 물량 투입 중심의 정보화 사업을 추진해 왔으며 그 결과 다른 여러 나라와 비교해서 손색이 없을 정도로 교육 현장에 정보화 환경이 조성되고 있고, 교육정보화를 통한 교육 혁신의 중요성을 인식하고 있다. 그러나 현재 학교에 보급된 교육정보자원은 학교마다의 실정을 고려하지 않은 대부분 공급자 중심의 획일화 된 규격에 일부 자원의 경우 여러 가지 이유로 충분한 활용이 이뤄지지 못하고 있다. 또, 교육정보자원의 관리 측면에서는 관리 주체가 학교마다 다르고 제대로 지정되지 않은 경우도 많아 업무의 효율성과 관리의 용이성이 떨어지고 있다. 따라서 본 연구에서는 10 여 년 동안 일선 학교에 보급된 교육정보자원을 보다 효과적으로 운영하기 위해서 현재 교육정보자원에 대한 활용, 관리 실태를 정확하게 파악하고, 조사 분석을 통해 문제점을 도출하고 이를 토대로 교육정보자원의 내실화 방안을 수립하여 제반 교육정보자원의 역할 및 기능을 재정립하고, 향후 신기술 수용 및 교육환경 변화에 능동적으로 대처할 수 있도록 하고자 한다.

• Horticultural Science & Technology
• /
• v.16 no.2
• /
• pp.229-232
• /
• 1998

This study was conducted to determine the properties of seedling plate papers currently used in commercial production, then to get basic information for manufacturing new seedling plate paper. Imported seedling plate paper had high wet tensile and burst strengths in its usage circumstances. Wet tensile strength was very high with 38.7% of dry tensile strength. Wet burst strength was also very high with 62.4% of dry burst strength. The seedling plate paper contained about 30% of synthetic fibers. It had 10 Gurley sec. in air permeability indicating effective movement of air. Seedling plate papers were' made in laboratory scale. For sufficient sizing degree, the addition of 0.5% AKD (alkylketene dimer) by weight was good enough. Additional amount of AKD more than 0.5% by weight caused strength loss even though improving sizing effect. The addition of wet strength reagent such as Finex-B 2% by weight resulted in good strength and air permeability.

• Journal of Advanced Navigation Technology
• /
• v.23 no.3
• /
• pp.228-236
• /
• 2019

Recently, multi-sensor integration techniques have been actively studied to obtain reliable and accurate navigation solution in GPS (Global Positioning System)-denied harsh environments such as urban canyons, tunnels, and underground roads. In this paper, we propose a low-cost ultrasonic-speedometer utilizing the characteristics of the ultrasonic propagation. An efficient integrated INS (inertial navigation system)/ultrasonic-speedometer navigation system is also proposed to improve the accuracy of positioning in GPS-denied environments. To evaluate the proposed system, car experiments with field-collected measurements were performed. By the experiment results, it was confirmed that the proposed INS/ultrasonic-speedometer system bounds the positioning error growth effectively even though GPS signal is blocked more than 10 seconds and a low-cost MEMS IMU (micro electro mechanical systems inertial measurement unit) is utilized.

• New Physics: Sae Mulli
• /
• v.68 no.11
• /
• pp.1208-1214
• /
• 2018

The one-step spin coating method is reported as an excellent thin film process because it can be easily used to fabricate high-quality methyl-ammonium lead tri-iodide ($MAPbI_3$) perovskite layers. One of the important things in the one-step spin coating method towards obtaining high-quality $MAPbI_3$ layers is the anti-solvent (AS) engineering, which consists of an one-step deposition of the $MAPbI_3$ film and dripping of the AS. The properties of the $MAPbI_3$ layer were found to be strongly influenced by the amount, dispensing speed, and spraying time of the AS solution. The $MAPbI_3$ solution was prepared by dissolving lead iodide and methyl-ammonium iodide in N,N-dimethylformamide and adding N,N-dimethyl sulfoxide. Diethyl ether (DE) was used for the AS solution. The results indicate that a $MAPbI_3$ layer appropriately sprayed with DE is beneficial for improving film quality and device efficiency because nucleation of $MAPbI_3$ layer is affected by the characteristics of DE, which affect the film's crystallinity, density, and surface morphology. The $MAPbI_3$ layer, which was optimized by using 0.7 mL of DE, a 3.03 mL/sec dispensing speed, and a 7 second time to spray after spinning showed the best efficiency of 13.74%, which was reproducible.