• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.282-283
• /
• 2005

Ion beam assisted deposition(IBAD) technique was used to produce biaxially textured polycrystalline MgO thin films for high critical current YBCO coated conductor. Hastelloy tapes were continuous electropolished with very smooth surface for IBAD-MgO deposition, RMS roughness of Hastelloy tape values below 2 nm and local slope of less than $1^{\circ}$. After the polishing of the tape an amorphous $Y_2O_3$ and $Al_2O_3$ are deposited Biaxially textured MgO was deposited on amorphous layer bye-beam evaporation with a simultaneous bombardment of high energy ions. We had developed the RHEED to measure in-situ biaxial texture of film surface as thin as tens angstrom. And also ex-situ characterization of buffer layers was studied using XRD and SEM. The full-width at half maximum(FWHM) out of plane texture of IBAD-MgO template is $4^{\circ}$.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.221-224
• /
• 2002

Superconducting electrical devices are under development in a national project in Korea. And KEPCO and LGIS are in charge of development of a resistive type fault current limiters(FCLs) with YBCO thin films. In order to realize FCLs, the rated power of FCLs must be increased. For this purpose, it is of great interest to increase of allowed voltage of unit component without electrical and thermal damages. So, meander lines were widely used for the conducting path to increase maximum electric field. In this research, numerical simulations on the electromagnetic behaviors of the device were carried out, especially focusing on the effect of meander line structures on the YBCO thin films. To evaluate the structures of meander lines, three types of meander lines were considered for numerical analysis using finite element method (FEM). In this simulation, both normal state and fault conditions were considered for calculation of electric field, current density, magnetic field density. And the simulation resulted are compared to find the optimum design of meander lines for resistive FCLs.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.6-11
• /
• 2004

YBa$_2$Cu$_3$$O_{7-x}$ (YBCO) films were deposited on MgO(100) and SrTiO$_3$(100) single crystal substrates by cold-wall type MOCVD method using continuous source supplying system. Under the deposition temperature of 740∼76$0^{\circ}C$, c-axis oriented YBCO films were obtained. In case of the YBCO films deposited on MgO (100) single crystal substrate, the critical temperature (T$_{c}$) was under 81 K regardless of the deposition conditions, whereas T$_{c}$ of the YBCO films deposited on SrTiO$_3$(100) single crystal substrate was 83∼84 K. The critical current (I$_{c}$) of the YBCO film deposited on SrTiO$_3$(100) single crystal substrate for 30 min was 49 A/cm-width and the critical current density (J$_{c}$) was 0.82 MA/$\textrm{cm}^2$ to film thickness of 0.6 ${\mu}{\textrm}{m}$. I$_{c}$ increased to 84.4 A/cm-width as the deposition time increased to 50 min, but J$_{c}$ decreased to 0.53 MA/$\textrm{cm}^2$ to film thickness of 1.8 ${\mu}{\textrm}{m}$.rm}{m}$.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.717-720
• /
• 1992

Since the discovery of High-Tc superconducting Y-Ba-Cu-O ceramics with critical temperature of about 90K, numerous efforts to prepare supercond ucting thin films with excellent qualities such as High-Tc and critical current density have been made. The samples were deposited onto $SiO_x$ substrates heated at 540$^{\circ}C$ - 600$^{\circ}C$ in a single target rf - magnetron sputtering system. The film thickness has 2000$\AA$ - 5000 $\AA$ with a rate of 16 $\AA$/min. and distance between target and substrate was 50 mm. The films were characterized by X - ray diffraction, scanning electron microscopy and critical temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1058-1062
• /
• 2000

We investigated resistive superconducting fault current limites (SFCLs) fabricated using YBCO thin films on 2-inch diameter sapphire substrates. Nearly identical SFCL units were prepared and tested. The units were connected in series and parallel to increase the current and voltage ratings. A serial connection of the units showed significantly unbalanced power dissipation between the units. This imbalance was removed by introducing a shunt resistor to the firstly quenched unit. Parallel connection of the units increased the current rating. An SFCL module of 4 units in parallel, each of which has minimum quench current rating. An SFCL module of 4 units in parallel, each of which has minimum quench current 25 A$\_$peak/, was produced and successfully tested at a 220 V$\_$rms/circuit. From the resistance increase, we estimated that the film temperature increased to 200 K in 5 msec, and 300 K in 120 msec. Successive quenches revealed that this system is stable without degradation in the current limiting capability under such thermal shocks as quenches at 220 V$\_$rms/.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.115-119
• /
• 1999

Ba$_2Cu_3O_{7-{\delta}}$ (YBCO) thin films were deposited by pulsed laser deposition using differently prepared targets: One was a conventionally solid-state sintered (SSS) target and the other was a modified melt-textured grown (MTC) target. Compared with SSS targets, MTG targets showed a well-connected microstructure consisting of much larger grains and the surface was Bess roughened with the cumulative laser incidence. YBCO films deposited from MTC targets showed a denser and smoother surface of the basal film than the case of SSS targets. The investigations of ${\alpha}$-axis outgrowths in the films indicated that the deposition using MTG targets would result in a more homogeneous and stable film growth as compared to the SSS targets. Also, TEM analysis revealed that the film deposited from MTG targets had a less granular microstructure that would reduce weak-link effects in the film.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.129-132
• /
• 1999

A new single solution source MOCVD technique for the deposition of YBCO film has been developed, using a ultrasonic atomizer to feed the precursors into an evaporation zone. This method being investigated as a basis for future long wire fabrication, for example the electric power use, the magnatic applications, etc.. YBCO films were prepared on MgO(100) substrate, using mixture of Y, Ba, and Cu ${\beta}$ -diketonate chelate was dissolve in tetrahydrofuran as a solution sources. X-ray diffraction measurement indicated that the thin film grew epitaxially with the c-axis orientation perpandicular to the surface of the surface.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.142-146
• /
• 1999

CeO$_2$ buffer layers and in-situ YSa$_2Cu_3O_{7-{\delta}}$ (YBCO) thin films were grown by pulsed laser deposition method on R-plane sapphire substrates. Superconducting properties and surface morphologies of YBCO thin films exhibit strong dependence on the crystallinity of CeO$_2$ buffer layer. The best a-axis oriented CeO$_2$ buffer layers could be grown at 800 $^{\circ}C$ of deposition temperature, 1.5 J/ cm$^2$ of laser energy density and 50 mTorr of oxygen pressure. The YBCO thin films on the a-axis CeO$_2$ buffer layer have Tc (R=0) ${\ge}$ 89.5 K, ${\delta}$Tc ${\sim}$ 0.5 K, and Jc ${\ge}$ 3.2 ${\times}$ 10$^6$ A/ cm$^2$ at 77 K.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.58-62
• /
• 1999

We fabricated a new hairpin type HTS 2-pole microstrip Bandpass filter to operate at 5.8GHz. The fabrication method was pulsed laser deposition and YBCO films were deposited on ${\alpha}$-A1$_2O_3$ substrates with a CeO$_2$ thin layer as a buffer layer. We developed a new style hairpin type filter by using interdigitide innerpole. Compared to the saute size regular hairpin type filters, our filter had a lower center frequency, bandwidth and loss by an amount of 14.5%, 29.6%, 0.5488dB, respectively. The size of the filters were 13.7${\times}$3.3mm. We did simulations on the several types of band pass filters by using HFSS and serenade. We measured growth rate and Tc of YBCO films grown on CeO$_2$/ ${\alpha}$-A1$_2O_3$ substrates which were rotated while growing films.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.34-37
• /
• 1999

We have fabricated YBCO/STO/YBCO multilayer by the pulsed laser deposition method varing the deposition condition of insulating STO layer. Superconducting properties of both YBCO layers are sensitively affected by the deposition condition of STO layer. We obtained the upper YBCO layer of T$_{c(zero)}\;{\sim}\;$90 K with a good reproducibility, however, T$_{c(zero)}$ of lower YBCO layer was decreased to about 80 K maybe due to the oxygen loss during the deposition of STO layer. Superconducting properties of both YBCO layers at every fabrication step were measured in order to study the reason for the deterioration of superconducting properties.