• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.609-610
• /
• 2010

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2011년도 추계학술논문집 2부
• /
• pp.398-401
• /
• 2011

초음파의 응용분야에는 음파 성질을 이용한 정보 측정분야와 에너지를 이용한 용접 및 가공 등을 들수 있다. 초음파 용접의 경우 저항용접이나 용융 용접을 적용할 수 없는 재료의 접합에 이용되는데 이는 모재를 음극간에 놓고 압입하면서 초음파를 발신하여 그 진동을 이용하는 용접방법이다. 압전소자의 경우 피에조 물질을 사용하는데 일반적으로 $150^{\circ}C$이상에서 분자구조의 변형을 일으켜 제 역할을 못하게 된다. 본 연구에서는 압전소자와 공구혼의 온도를 최적으로 유지하기 위하여 추가적인 공기 유로와 방열핀을 설계하여 이것이 방열성능에 미치는 영향에 대해 고찰하였다.

• 한국정밀공학회지
• /
• 제29권8호
• /
• pp.879-886
• /
• 2012

The ultrasonic horn used for bonding of flip chip has been designed to vibrate at a natural frequency. The ultrasonic horn must be manufactured accurately in physical terms, because the small change of mechanical properties may result in the significant change of natural frequency. Therefore, tight tolerance is inevitable to keep the natural frequency in acceptable range. However, since tightening of the tolerance increases the manufacturing cost significantly, trade-off between the cost and accuracy is necessary. In this research, an attempt was made to design the ultra sonic horn within acceptable natural frequency while the manufacturing cost was kept as low as possible. For this purpose, among the 18 tolerances of physical terms of the ultrasonic horn, the most important 4 factors were selected using Taguchi method. The equation to relate those main factors and the natural frequency was made using response surface method. Finally, optimal design scheme for minimum manufacturing cost without a loss of performance was determined using SQP method.

• 한국공작기계학회논문집
• /
• 제13권3호
• /
• pp.53-60
• /
• 2004

We have developed and manufactured an experimental ultrasonic polishing machine with frequency of 20kHz at the power of vibration 1.7㎾ for effective ultrasonic polishing in processing of high hardness material. Design of the horn is performed by the FEM analysis. The following conclusions were empirically deduced through experimental results to clarify the major elements which affect the surface roughness during the ultrasonic process by following the experimental plans. The ultrasonic polishing machine has been developed in parts of structure part, ultrasonic generator, vibrator. We were able to process the high hardness material without difficulty as a result of ultrasonic polishing by utilizing the groove added step-type horn. Through analyzing by applying the experimental plans, the rotating speed of the horn was determined to be the major factor in influencing the surface roughness. In the case of ceramic, wafer, we were able to obtain good surface roughness when the feed rate and the ultrasonic output were higher. Because the load on slurry particle increases when the ultrasonic output is higher, the processed surface becomes worse in the case of optical glass.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.583-588
• /
• 2007

This paper investigates the vibration characteristics of a wire-bonding transducer horn for high speed welding devices. The sample wire-bonder uses the input frequency of 136 kHz. The ultrasonic excitation causes the various vibrations of transducer horn and capillary. The vibration modes and frequencies close to the exciting frequency are identified using ANSYS. The nodal lines and amplification ratio of the ultrasonic horn are also obtained in order to evaluate the bonding performance of the sample wire-bonder system. The FEM results and experimental results show that the sample wire-bonder system uses the bending mode of 136 kHz as principal motion for bonding. The major longitudinal mode exists at 119 kHz below the excitation frequency. It is recommeded that the sample system is to set the excitation frequency at 119 kHz to improve bonding performance.

• 한국정밀공학회지
• /
• 제28권3호
• /
• pp.363-369
• /
• 2011

In this study, a direct pattern forming process on a plastic film using ultrasonic vibration energy is investigated. A tool horn containing micro-patterns is attached to an ultrasonic power supply, and is used to press a plastic film with ultrasonic vibration in order to replicate micro-patterns on the surface of the plastic film. To replicate micro-patterns with high accuracy, the tool horn should be designed to allow only the longitudinal vibration, not the transverse vibration. For this purpose, the design of a tool horn is investigated through finite element analysis, from which the resulting natural frequency of the tool horn can be adjusted in the range of the ultrasonic power supply. The analysis result is then reflected on the optimal design and fabrication of the tool horn. The validity of the developed tool horn is discussed through pattern-forming experiments using the ultrasonic vibration of the developed tool horn.

• 한국기계가공학회지
• /
• 제12권2호
• /
• pp.55-61
• /
• 2013

The horn is a key part of the ultrasonic welder. As the shape, mass and material of a horn have effects on the resonant frequency and the vibration mode in ultrasonic welding, a horn has to be designed and manufactured accurately. In this study, 40kHz band horn was designed and manufactured through the vibration mode and finite element analysis. A result of modal analysis showed that the natural frequency of the horn was 39,794Hz, and the frequency response by a harmonic response analysis was 39,800Hz - close to the intended frequency, 40kHz. In addition, weldability of the developed horn was estimated by welding of two Ni sheets and tensile-shear test of welded samples. It was shown the developed horn could be used in metal sheet welding.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2750-2753
• /
• 2008

This paper introduce the CFD analysis for predicting the heat transfer at the Ultrasonic horn. Approximately Ultrasonic horn separates two part. One is preheating part and the other is cooling part. Temperature of preheating part rise up by $260^{\circ}C$ that make it possible to attach a chip to a semiconductor. Also there is a piezo material in the cooling part. When piezo work, it generates heat of $100^{\circ}C$. It can stand by $150^{\circ}C$. But the high temperature conducted from the preheating part has a bad affect on the piezo. These situation make it necessary cooling at piezo. Previously except of the piezo, all of them are composed of the SUS440c that has good thermal conductivity. This study shows way that not only cooling the piezo but also cutting off the conduction between preheating part and cooling part by using the Ti and Duralumin that have low thermal conductivity compare with the SUS440c. Conclusion of CFD analysis that the heat coming from the piezo can't be transferred the horn cause of the Ti and Duralumin.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1991년도 춘계학술대회 논문집
• /
• pp.39-45
• /
• 1991

최근 진동 절삭 가공 및 용착 등에 초음파 진동을 동력적으로 응용하려는 시도가 급증하고 있다. 이 분야에서는 진동자에서 발생되는 미소한 진폭의 적은 초음파 에너지를 큰 에너지로변환시키는 방법으로서 진동자의 끝단에 진동자와 동일한 진동수의 고유진동수를 가진 부스터와 tool horn을 부착하여 공진에 의해 진폭의 증폭으로 큰 에너지를 얻고 있다. 그러나 부스터와 tool horndml의 고유 진동수가 진동자의 진동수와 일치하지 않을 경우에는 tool horn 의 끝단에 진동이 전달되지 않는 결과를 초래하게 된다. 본 연구에서는 유한 요소법을 이용하여 축대칭 및 3차원 형상의 tool horn에 대한 고유 진동수 계산 퍼스널 컴퓨터만으로도 tool horn을 설계할 수 있도록 하여 이 결과를 실용 tool horn 설계 제작에 손쉽게 이용할 수 있도록 하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.231-234
• /
• 2002

Ultrasonic machining technology has been developed over recent years for the manufacture of cost-effective and quality-assured precision parts for several industrial application such as optics, semiconductors, aerospace, and automobile. Ultrasonic machining process is an efficient and economical means of precision machining of ceramic materials. The process is non-thermal, non-chemical and non-electric and hardly creates changes to the mechanical properties of the brittle materials machined. This paper describes the characteristics of the micro-hole of $\textrm{Al}_2\textrm{O}_3$ by ultrasonic machining with tungsten carbide tool. The effects of various parameters of ultrasonic machining, including abrasives, machining force and pressure, on the material removal rate, hole quality, and tool wear presented and discussed. The ultrasonic Machining of micro-holes in ceramics has been under taken and the machining mechanism in the ultrasonic machining of ceramics based on the fracture-mechanics concept has been analyzed.