• Progress in Medical Physics
• /
• v.19 no.1
• /
• pp.42-48
• /
• 2008

Bio-implantable devices such as heart pacers, gastric pacers and drug-delivery systems require power for carrying out their intended functions. These devices are usually powered through a battery implanted with the system or are wired to an external power source. This paper describes an inductive power transmission link, which was developed for an implantable stimulator for direct stimulation of denervated muscles. The carrier frequency is around 1MHz, the transmitter coil has a diameter of 46mm, and the implant coil is 46mm. Data transmission to the implant with amplitude shift keying (ASK) and back to the transmitter with passive telemetry can be added without major design changes. We chose the range of coil spacing (2 to 30mm) to care for lateral misalignment, as it occurs in practical use. If the transmitter coil has a well defined and reliable position in respect to the implant, a smaller working range might be sufficient. Under these conditions the link can be operated in fixed frequency mode, and reaches even higher efficiencies of up to 37%. The link transmits a current of 50 mA over a distance range of 2-15 mm with an efficiency of more than 20% in tracking frequency. The efficiency of the link was optimized with different approaches. A class E transmitter was used to minimize losses of the power stage. The geometry and material of the transmitter coil was optimized for maximum coupling. Phase lock techniques were used to achieve frequency tracking, keeping the transmitter optimally tuned at different coupling conditions caused by coil distance variations.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.158-163
• /
• 2002

최근 전자통신기기의 급속화된 발전과 함께 전자부품에 대한 초소형화, 고성능화가 요구되고 있다. 특히 노트북 컴퓨터나, PDA, LCD 모니터와 같이 박막 액정 표시장치(Thin Film Transistor Liquid Crystal Display, TFT-LCD)가 대표적인 예라 볼 수 있다. 이러한 박막 액정 표시장치는 그 내부에 냉음극 형광램프(Cold Cathode Fluroscent Lamp)가 있어서 백라이트의 역할을 하는데 냉음극 형광램프의 특성상 초기 고압의 구동전압을 인가시킬 수 있는 인버터가 필수적이라 하겠다. 본 논문에서는 18인치(4_CCFL), 20인치(6_CCFL) TFT-LCD 모니터용, 멀티램프 구동 인버터를 설계 제작하여 90%에 가까운 효율을 얻었다. 코일손실 및 전자유도의 장애가 없고 불연성의 장점을 가지고, 소형화가 가능한 적층형 압전 변압기를 제작하고 이 제작된 적층형 압전 변압기의 전기적 특성분석을 통한 방전램프 구동용 인버터의 승압용 변압기로써 적용이 가능함을 확인하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4C
• /
• pp.163-174
• /
• 2009

Mechanical device using the load cell or strain gage sensor can be influenced by tempearute changes because temperature change can cause a shift in the load cell or straing gage output at zero loading. In this paper, micro cone penetrometers with 1~7mm in diameter, are developed by using an optical fiber sensor (FBG: Fiber Bragg Grating) to compensate the continous temperature change during cone penetration test. Note the temperature compensated method using optical fiber sensor which has hair-size in diameter, and is not affected by environmental conditions because the measured data is the wavelength shifting of the light instead of the intensity of the electric voltage. Temperature effect test shows that the output voltage of strain gage changes and increases with an increase in the temperature. A developed FBG cone penetrometer, however, achieves excellent temperature compensation during penetration, and produces continuous change of underground temperature. In addition, the temperature compensated FBG cone shows the excellent sensitivity and detects the interface of the layered soils with higher resolution. This study demonstrates that the fiber optic sensor renders the possibility of the ultra small size cone and the new fiber optic cone may produce more reliable temperature compensated tip resistance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.8
• /
• pp.686-696
• /
• 2017

The major objective of this study is to develop and verify the KAUSAT-5 based on the modular 3U CubeSat standard platform. In the mechanical system design of a 3U standard platform, subsystem and micro equipment functions/performance should be integrated and miniaturized on micro-sized PCBs and electrical capability was maximized to accommodate multiple payloads. KAUSAT-5 is 3U-sized Cubesat which will be operated in Low Earth Orbit(LEO), which implements mainly two scientific missions; one is to observe the Earth through infrared camera and the other is to measure space radiation with a Geiger Muller tube. An additional mission is to verify the equipment(device) such as VSCMG and fuzzy logic-based MPPT internally developed. The results of ETB, qualification and acceptance level environmental tests were shown to verify standard platform and KAUSAT-5 Cubesat.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.3 s.40
• /
• pp.9-12
• /
• 2006

We have designed and fabricated micro power generators by electroplating which is important in MEMS(micro electro mechanical system) technique. We have electroplated MEMS coils on the glass substrates and have chosen one of these coils for experiments. The thickness, width, and length of the coil are $7{\mu}m,\;20{\mu}m$, and 1.6 m, respectively. We have analyzed the structure of MEMS coil by SEM. We have made a vibrating system for reproducible results in measurement. With reciprocating a magnet on the surface of a fabricated winding coil, the micro power generator produce an alternating voltage. We have changed the vibrational frequency from 0.5 Hz to 8 Hz. The generated voltage was 106 mV at 3 Hz and 198 mV at 6 Hz. We aim at the micro power generator which can change vibration energy to useful electric energy.

• Journal of IKEEE
• /
• v.25 no.2
• /
• pp.315-321
• /
• 2021

In this paper, we have developed the multiple channel measurement system for IC Socket Test. The one can test the current-voltage measurements for pitting the several device specification, which analyze the thin current from several ㎂ to 5A with very low resistor mΩ. The increasement of the IC socket channel with lead pitch under 0.25 mm be need to perform several functions, concurrently. The system to perform these functions be designed to integrate several SMU(source measure unit) on board. So, we can reduce the 2 minutes test time per channel point to 40 sec, with daisy chain test method. Using by graphic interface, I-V curve mode and data logging technologies, we can implement the test flow methods and can make economies the time and cost.

• Composites Research
• /
• v.35 no.6
• /
• pp.371-377
• /
• 2022

Triboelectric nanogenerator (TENG) devices have generated a lot of interest in recent decades. TENG technology, which is one of the technologies for harvesting mechanical energy among the energy wasted in the environment, is obtained by the dual effect of electrostatic induction and triboelectric charging. Recently, a multilayer thin film stacking method (or layer-by-layer (LbL) self-assembly technique) is being considered as a method to improve the performance of TENG and apply it to new fields. This LbL assembly technology can not only improve the performance of TENG and successfully overcome the thickness problem in applications, but also present an inexpensive, environmentally friendly process and be used for large-scale and mass production. In this review, recent studies in the accomplishment of LbL-based materials for TENG devices are reviewed, and the potential for energy harvesting devices reviewed so far is checked. The advantages of the TENG device fabricated by applying the LbL technology are discussed, and finally, the direction and perspective of this fabrication technology for the implementation of various ultra-thin TENGs are briefly presented.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.67.2-67.2
• /
• 2017

본 연구에서는 $SiO_2$ 미세구조 상에 Pd 나노입자(NPs)를 증착하여, 불소화된 마이크로-나노 계층구조를 갖는 Pd-decorated $SiO_2$($Pd/SiO_2$)를 제작하였다. 마이크로 크기의 거칠기를 갖는 $SiO_2$ 층은 졸-겔 공정을 사용해서 제조된 용액을 전기분사함으로써 제조되었다. 이어서, 자외선(UV)을 이용한 광 환원법을 이용해 Pd 나노입자를 $SiO_2$ 층에 형성했다. 생성된 표면은 마이크로-나노의 계층구조 형태를 보여주었다. 해당 시편의 불소화 처리 후, 마이크로-나노의 계층구조 표면은 $170^{\circ}$ 이상의 물 접촉각(water contact angle; WCA) 및 $5^{\circ}$ 이하의 슬라이딩 각(sliding angle)을 보여줌으로써 물에 대해 탁월한 소수성을 나타내었다. 또한, 커피($CA=161^{\circ}$), 우유($CA=162^{\circ}$), 쥬스($CA=163^{\circ}$), 그리고 글리세롤($CA=165^{\circ}$)에 대해서도 우수한 소수 특성을 보여주었다. 또한, 이들 $Pd/SiO_2$ 층은 우수한 장기내구성 및 자외선 저항성을 보여주었다. 그리고 이어진 기름에 대한 접촉각 측정을 통해 해당 시편이 소유 특성이 아닌 친유 특성을 보여준다는 것을 확인할 수 있었고, 기름에 대한 CA는 약 ${\sim}10^{\circ}$로 매우 우수한 친유 특성을 나타내었다. 이와 같은 결과는 자체세정이 가능한 표면 및 지능형 물/기름 분리 시스템과 같은 스마트 장치에서 초소수성-친유성 특성을 갖는 계층구조의 $Pd/SiO_2$ 층을 사용할 가능성을 명확하게 보여준다고 판단된다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.105-105
• /
• 2006

IT 산업 및 반도체 산업이 발전함에 따라 초소형, 고집적화 시스템의 요구에 대응하기 위해서 고해상도 및 고정밀의 패턴 구현에 관한 많은 연구가 진행되고 있다. 이러한 연구는 각종 산업제품의 PCB(Printed Circuit Board) 및 디스플레이 장치인 PDP(Plasma Display Panel), LCD(Liquid Crystal Display) 등에 적용되어 널리 응용되고 있다. 현재 널리 사용되는 인쇄 회로 기판은 마스킹 후 선택적 에칭 방식을 적용하여 금속 배선을 형성하는 방식을 적용하고 있다. 이러한 방식은 설계가 변경될 경우 마스크를 다시 제작해야 하는 번거로움이 있어 설계 변경이 용이하지 않고 더욱 길어진 생산시간의 증가로 인하여 생산성 및 집적도가 떨어지게 된다. 따라서 최근에는 이러한 한계를 극복하기 위한 방안이 여러 가지 측면에서 시도되고 있으며, 그 중에서도 Inkjet Printing 기술에 대한 관심이 증가하고 있다. 본 연구에서는 Inkjet Printing 방식을 적용하여 금속 배선을 형성하고 선폭과 두께의 오차를 줄여 배선의 Tolerance 를 개선할 수 있는 방안을 제안하였다. Inkjet Printing 방식을 이용한 기존의 금속 배선 형성은 고해상도의 DPI(Dot Per Inch)에서 잉크 액적이 뭉치는 Bulge 현상이 발생되어 원하는 형상 및 배선의 폭을 구현하는데 어려움이 있었다. Bulge 현상은 배선의 불균일성을 야기할 뿐만 아니라 근접한 배선의 간섭에도 영향을 미처 금속 배선의 기능을 할 수 없는 단점을 발생시킨다. 따라서 본 연구에서는 이러한 Bulge 현상을 줄이고 배선간의 간섭을 방지하여 원하는 배선을 용이하게 형성할 수 있는 순차적 인쇄 방식을 적용하였다. 본 연구에서는 노즐직경 35um 의 Inkjet Head 와 나노 Ag 입자 잉크를 사용하여 Glass 표면 위에 배선을 형성하고 배선의 폭과 두께를 측정하였다. 또한 순차적 인쇄 방식을 적용하여 700DPI 이상의 고해상도에서 나타날 수 있는 Bulge 현상이 감소하였음을 관찰하였으며 금속 배선의 Tolerance를 10%내외로 유지할 수 있음을 확인하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.630-633
• /
• 2021

Microphones can convert received voice signals to electric signals. They have been widely used in various industries such as radios, smart devices and vehicles. Recently, the demands for small size and high sensitive microphones are increased according to the minimization of wireless earphone with the development of smart phone. A MEMS system is a good candidate for an ultra-small size microphone of a next generation and a read out IC for high sensitive MEMS sensor is researched from many industries and academies. Since the microphone system has a high sensitivity from environment noise and electric system noise, the system requires a low noise power supply and some low noise design techniques. In this paper, a low noise LDO is presented for small size MEMS microphone systems. The input supply voltage of the LDO is 1.5-3.6V, and the output voltage is 1.3V. Then, it can support to 5mA in the light load condition. The integrated output noise of proposed LDO form 20Hz to 20kHz is about 1.9uV. These post layout simulation results are performed with TSMC 0.18um CMOS technology and the size of layout is 325㎛ × 165㎛.