Journal of Korean Society of Environmental Engineers
/
v.32
no.4
/
pp.325-332
/
2010
This study was conducted with the experiment of solubilisation of excess sludge by microbubble ozone process. To improve ozone contact efficiency, microbubble ozones which its diameter were the avearge 30 ${\mu}m$, microbubble size less than 40 ${\mu}m$ occupied about over 90% of all. In treating sludge using microbubble ozones, in case microbubble ozones are injected at microbubble ozone dosage of 0.34 g $O_3/g$ SS or less regardless of sludge concentration, microbubble ozone consumption rate was found to be 100% with no emission of waste ozones. In treating sludges by each concentration, in case the initial SS concentration of sludge is set to 6,447 mg/L, 5,557 mg/L, 3,180 mg/L, 1,092 mg/L and 515 mg/L, the amount of removed SS tended to increase with increase in initial SS concentration for the same microbubble ozone dosage, and treatment of sludge with high initial SS concentration was effective in raising the oxidation efficiency of microbubble ozones. On the other hand, as a result of reviewing acid, alkali and microbubble ozone treatment as composite treatment of sludge, use of acid treatment for the pre-treatment of microbubble ozone was more effective than alkali treatment, and in case of treatment at microbubble ozone dosage 0.05g $O_3/g$ SS with the concentration of sulfuric acid infused in the sludge, the amount of removed SS, 153.9 g, was 1.9 times more than 81.2 g the amount of single treatment of microbubble ozone.
The purpose of this study was to compare mineral trioxide aggregate (MTA; Dentsply, Tulsa Dental, Tulsa, OK, USA), which is widely used as root-end filling material, with DiaRoot BioAggregate (DB; Innovative BioCaramix Inc, Vancouver, BC, Canada), newly developed product, by using MG63 osteoblast-like cells. MTA, DB, and Intermediate Restorative Material (IRM; Dentsply Caulk, Milford, DE, USA) were used for root-end filling material while tissue culture plastic was used for control group. Each material was mixed and, the mixtures were left to set for 24 hours. MG63 cells were seeded to each group and then they were cultured for attachment for 4 hours. Following the attachment of cells to the root-end filling material, early cellular response was observed. After another 12 hours'culture, the level of attachment between cells and material was observed and in order to identify the effect of each material to bone formation, transforming growth factor beta1 ($TGF{\beta}1$) and osteocalin (OC) were estimated by using enzyme-linked immunosorbent assay (ELISA), and the amount of alkaline phosphatase (ALP) was also measured. The data were analyzed using one-way ANOVA. As a result, only at OC and the number of cells which were attached to materials, there was no statistical difference between MTA and DB. At other items, there was statistically significant difference in all groups. Although DB has not shown exactly the same cellular response like that of MTA, the number of attached cells shows that biocompatibility of the material and OC indicates bone formation rate. Therefore, if DB is used for root end filling material, it is expected to lead to similar results to MTA.
ETSI BRAN (Broadband Radio Access Network)는 고속 무선 LAN 또는 고정 광대역 무선액세스 네트워크에서의 무선 접촉 계층과 ATM 및 IP(Internet Protocol) 코어 네트워크와의 연동을 위한 일부 기능을 표준화하기 위한 과제이다. 특히, BRAN의 HIPERLAN type-2(HIPERLAN/2)의 경우에는 과제의 범위는 무선 접속면, 무선 부시스템에서의 서비스 인터페이스, 서비스 구현에서 요구되는 연동 및 각종 지원 기능을 표준화하며, 무선 접속면의 경우에는 다수 벤더간의 상호 호환성을 제공할 수 있는 인터페이스를 구현하는 것이다. HIPERLAN/2의 기술 규격은 코어 네트워크와 독립적인 물리계층 및 데이터 링크 제어 (DATA Link Control: DLC) 계층과 서로 상이한 코어 네트워크와의 연동을 위한 네트워크 수렴 부계층을 다루게 될 것이며, 초기 단계에서는 ATM과 IP 코어 네트워크와의 연동 기능을 제시하게 될 것이다. 따라서 HIPERLAN/2기반의 시스템 규격을 제시하기 위해서는 네트워크 계층 및 기타 상위 계층에 대한 규격이 요규되며, 이는 ATM Forum에서의 무선 ATM 신호 방식 규격, IETF(Internet Engineering Task Force)의 IP규격, 그리고 ETSI의 SMG (Special Mobile Group) 프로젝트에서 표준화되고 있는 UMTS (Universal Mobile Telecommunication Service) 규격 등과 접목될 것이다. 결과적으로 무선 ATM 관점에서는 완전한 시스템 규격 작성은 ETSI BRAN과 ATM Forum에서 무선 접속 규격과 이동성 관리 및 신호 방식으로 각각 이원화되어 진행되고 있다. 현재 물리 계층에서의 전송 방식은 OFDM(Orthogonal Frequency Division Multiplexing)으로 확정되었으며, DLC 계층에서는 고정 길이의 TDD (Time Division Duplexing) TDMA 프레임 구조를 기반으로 AP (Access Point)에 의해 동적으로 상향 링크 자원을 예약 할당하는 매체 접근 제어 (Medium Access Control: MAC) 프로토콜이 고려되고 있다. 이와 같은 DLC 계층에서는 기본적으로 짧은 길이의 패킷을 통해 다양한 대역폭의 멀티미디어 트래픽을 효율적으로 수용하면서 ATM 네트워크뿐만 아니라 향후 IP 네트워크에서 요구하는 각 서비스별 QoS (Quality of Service)를 개별적으로 보장할 수 있는 기능을 구현하고자 한다. 향후 이 부문에 대한 표준화가 본격적으로 진행될 것으로 예상되며 HIPERLAN/2의 경우에는 1999년 중반까지 1차 기능 규격을 완료할 예정이며, BRAN 전반에 대한 완전한 규격을 2002년까지 완성하는 것을 목표로 하고 있다.
Kim, Dae-Young;Park, Hyung-Seo;Kim, Woong-Kyeom;Pyo, Chang-Ryul;Kim, Heon-Young
Transactions of the Korean Society of Mechanical Engineers A
/
v.36
no.3
/
pp.347-353
/
2012
Recently, multi-functionalization (as in smart phones) has been in demand, and the connectors connecting the electrical signals of each board in a cellular phone have become key components. The miniaturization of these connectors is required to achieve a finer pitch design and enhance the electrical signal transfer capacity. However, the miniaturization of connectors reduces the structural safety, and a finer pitch design may cause contact problems under external impact. In this paper, a preliminary design for miniaturized, finer-pitch connectors is suggested for a product with 50 pins and a thickness of 0.2 mm. The assembly process of the FPCB (Flexible Printed Circuit Board) and connector was simulated to ensure the holding force between the two components and avoid overstressing. The design optimization process was performed with the Taguchi method. Fatigue analysis was also conducted to predict the fatigue life of the terminal, and the theoretical and experimental results were compared.
Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
/
v.14
no.6
/
pp.35-42
/
2000
In this paper, AE(Acoustic Emission) signals detected from the growth of the electrical tree in an epoxy resin under ac high-voltage application were analysed to diagnose the insulation deterioration of cast-resin power transformer. Frequency spectra of AE signals generated from the magnetizing and the load currents in the actual operating cast-resin power transformer of 500[kVA] under distribution system of 22.9[kV] were also analysed to distinguish the AE signals due to void discharges from the magnetic circuit noises in the core of the transformer. As the experimental results, we could distinguish the AE signals whether those signals were caused due to the void discharges or due to the magnetic circuit noises by analyzing the frequency spectrum of AE signals. The frequency spectra of AE signals generated from the cast-resin power transformer in operation due to both the magnetizing and the load currents appeared in the range of 40-120[kHz], but the frequency band of AE signals emitted from the void discharges in an epoxy resin sample was about 50[kHz] to 230[kHz].
The purpose of this study was to find the distribution and measurement of compressive and tensile stress when intrusi- on arch wire is forced engage with upper canine and to analysis stress at each section through FEM. And we compare compressive and tensile ratio at each section. The results were as follows. 1. At FA point and cemento-enamel junction of upper canine, compressive and tensile force ratio is about the same. 2. At apex, compressive force is the four times as tensile force. ; In intrusion, we show root resorption at apex. 3. At Cemento-enamel junction, the compressive and tensile force show the maximun value except FA Point.
Transactions of the Korean Society of Mechanical Engineers A
/
v.41
no.9
/
pp.799-807
/
2017
In this paper, a new method is proposed for estimating pedestrians' walking velocity based on lower-limb kinematics and wearable inertial measurement unit (IMU) sensors. While the soles and ground are not in contact during the walking cycle, the walking velocity can be estimated by integrating the acceleration output of the inertial sensor mounted on the pelvis. To minimize the effects of acceleration measurement errors caused by the tilt of the pelvis while walking, the estimated walking velocity based on lower-limb kinematics is imposed as the initial value in the acceleration signal integration process of the pelvis inertial sensor. In the experiment involving outdoor walking for six minutes, sensor drift due to error accumulation was not observed, and the RMS error in the walking velocity estimation was less than 0.08 m/s.
Magnetic gear can transmit torque without any mechanical contact among rotational parts in rotating mechanical systems. Especially, magnetic gear using rare-earth PMs can be used in variety of industry application because of their great power efficiency. Thus, recent trend shows that magnetic gear can be replaced with common mechanical gear. This paper deals with comparison and torque analysis for magnetic gears with parallel and Halbach magnetization according to various design parameters. Using a two dimensional (2D) finite element (FE) analysis, suitable gear ratio is selected. We performed analysis for magnetically connected inner and outer torque with respect to various design parameters including thickness of inner and outer PM, steel pole angle, segments of Halbach array and magnetization pattern of inner and outer PMs. Finally, we can obtain improved design model having parallel and Halbach magnetization with larger torque, compared with an initial design model.
Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
/
2003.10a
/
pp.174-175
/
2003
현재 유통되고 있는 일반백미의 경우 소비자가 밥을 짓기 위해서는 쌀을 씻어야하는 번거로움 뿐만아니라 쌀 중량의 약 15배의 물이 소요되고, 또한 이때 발생된 쌀뜨물이 수질오염의 원인이 되기 때문에 무세미가공 및 보급 필요성이 점차 높아지고 있다. 무세미 가공분야의 선진국인 일본의 경우 ‘92년부터 습식 무세미조제기가 실용화되기 시작, 현재 사다께 등 6개사에서 기계장치를 생산보급 하고 있으며, 무세미의 유통도 일반화되어가고 있는 추세이다. 국내의 경우 무세미조제기는 근래에서야 습식 무세미 조제설비가 국산화되어 보급초기 단계 있으며, 무세미의 안정적 가공 및 보급을 위해서는 앞으로 많은 연구가 이루어져야 할 것으로 생각된다. 특히 습식의 경우 쌀이 물에 접촉하는 시간이 길 경우 품질저하의 우려가 크고, 쌀중량의 1.4배에 해당하는 물이 가공과정에 필요하기 때문에 물사용량을 억제할수 있는 가공기술의 개발 필요성이 커지고 있다. 따라서 본 연구에서는 물사용량을 최소화 할 수 있는 무세미 조제시스템을 개발하고자 하였으며, 주요결과를 요약하면 다음과 같다. 시작기는 연마 및 공기세척부, 정전기 세척부, 미세가수세척부로 구성하여 쌀이 단계적으로 세척될 수 있도록 제작되었다. 성능시험 결과, 각 세척공정별 세척수의 탁도 감소효과는 연마 및 공기크리닝부에서 22.67ppm, 정전기 크리닝부에서 8.33ppm, 미세가수세척부에서 17.34 ppm이 감소되는 것으로 나타났다. 특히 정전기세척부의 탁도감소 효과는 다른 두공정에 비해 작지만 제거가 쉽지 않은 미세한 쌀겨들을 제거하여 탁도를 개선을 시켰기 때문에 미세가수세척장치에서 가수량을 적게 사용하는데 기여한 것으로 판단된다. 가공시 적정 탁도를 확보할 수 있는 가수량은 430cc/kg로 기존의 습식에 비해 약 69%정도 세척수 절감효과가 있었다. 이때 미세가수세척부의 원통스크린 회전수는 108, 205rpm범위가 적정한 것으로 나타났다. 쌀의 품위는 탁도가 가공전 97.33ppm(일반백미)에서 가공후 최대 48.00ppm으로 낮아졌으며, 백도도 가공전 36.80에서 42.80으로 향상되어 씻지 않고도 밥을 지을수 있는 무세미 가공이 가능하였다. 이밖에 쇄립률은 가공전 5.30%에서 7.37%로 다소 증가하는 것으로 나타났고, 함수율은 가공전 15.60%에서 15.80%로 약 0.2%가 증가하였으나 기존의 연구결과에 비춰볼 때 문제가 되지 않을 것으로 여겨진다.
Interfacial properties and microfailure degradation mechanisms of the oxygen-plasma treated biodegradable poly(p-dioxanone) (PPDO) fiber/poly(L-lactide) (PLLA)composites were investigated for the orthopedic applications as implant materials using micromechanical technique and surface wettability measurement. PPDO fiber reinforced PLLA composite can provide good mechanical performance for long hydrolysis time. The degree of degradation for PPDO fiber and PLLA matrix was measured by thermal analysis and optical observation. IFSS and work of adhesion, $W_a$ between PPDO fiber and PLLA matrix showed the maximum at the plasma treatment time, at 60 seconds. Work of adhesion was lineally proportional to the IFSS. PPDO fiber showed ductile microfailure modes at We initial state, whereas brittle microfailure modes appeared with elapsing hydrolysis time. Interfacial properties and microfailure degradation mechanisms can be important factors to control bioabsorbable composites performance because IFSS changes with hydrolytic degradation.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.