• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.6 s.348
• /
• pp.1-8
• /
• 2006

In the asynchrous OFCDM(Orthogonal Frequency and Code Division Multiplexing) system, a three-step cell search algorithm is performed for the initial synchronization in the following three steps: OFCDM symbol timing, i.e., Fast Fourier Transform(FFT) window timing is estimated employing guard interval (GI) correlation in the first step, then the frame timing and CSSC (Cell Specific Scrambling Code) group is detected by taking the correlation of the CPICH(Common Pilot Channel) based on the property yeilded by shifting the CSSC phase in the frequency domain. Finally, the CSSC phase within the group is identified in the third step. This paper proposes a modification code(PCSSCG:Patial Cell Specific Scrambling Code Group) of the conventional CPICH based cell search algorithm in the second step which offers MS(Mobile Station) complexity reductions with the nearly same performance. The proposed method is to be compared and verified through the computer simulation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.765-770
• /
• 2001

Metal-ferroelectric-insulator- semiconductor(MFTS) devices by using rapid thermal annealed (RTA) LiNbO$_3$/AIN/Si(100) structures were successfully fabricated and demonstrated nonvolatile memory operations. Metal-insulator-semiconductor(MIS) C-V properties with high dielectric AIN thin films showed no hysteresis and good interface properties. The dielectric constant of the AIN film calculated from the capacitance at the accumulation region in the capacitance-voltage(C-V) characteristics was about 8. The C-V characteristics of MFIS capacitor showed a hysteresis loop due to the ferroelectric nature of the LiNbO$_3$ thin films. Typical dielectric constant value of LiNbO$_3$ film of MFIS device was about 23. The memory window width was about 1.2 V at the gate voltage of $\pm$5 V ranges. Typical gate leakage current density of the MFIS structure was the order of 10$^{-9}$ A/$\textrm{cm}^2$ at the range of within $\pm$500 kV/cm. The ferroelectric capacitors showed no polarization degradation up to about 10$^{11}$ switching cycles when subjected to symmetric bipolar voltage pulse(peak-to-peak 8 V, 50 % duty cycle) in the 500 kHz.

• Korean Journal of Construction Engineering and Management
• /
• v.4 no.4 s.16
• /
• pp.192-200
• /
• 2003

The object of this research is to develop a computerized algorithm of cost estimation method to forecast the total construction cost in the bidding stage by the historical and elemental work cost data. Traditional cost models to prepare Bill of Quantities in the korea construction industry since 1970 are not helpful to forecast the project total cost in the bidding stage because the BOQ is always constant data according to the design factors of a particular project. On the contrary, statistical models can provide cost quicker and more reliable than traditional ones if the collected cost data are sufficient enough to analyze the trends of the variables. The estimation system considers non-deterministic methods which referred to as the 'Monte Carlo simulation. The method interprets cost data to generate a probabilistic distribution for total costs from the deficient elemental experience cost distribution.

• The KIPS Transactions:PartC
• /
• v.12C no.4 s.100
• /
• pp.559-570
• /
• 2005

ECN is accurate in determining traffic congestion since it explicitly notifies the incipient congestion. Therefore, ECN method has been thoroughly studied in the field of wireless TCP. This paper introduces a formula to find the optimal threshold for ECN marking. We have implemented a Petri net model of 'TCP with ECN strategy' and performed simulations on it in order to verify the validity of the formula. We have also introduced ideas of applying the formula in practice. The primary contribution of this paper is proposing a formula to find the optimal threshold for ECN marking. However, introducing the Petri net model of 'TCP with ECN strategy' is no less valuable contribution because it can be helpfully used by the researchers in studying network protocols. We have built the Petri net model by modifying the existing Petri net model of TCP. In order to add ECN strategy to the existing model, we have mainly modified the network part. We have also modified sender part and receiver part as well.

• Journal of Advanced Navigation Technology
• /
• v.15 no.6
• /
• pp.1132-1137
• /
• 2011

In this paper, we propose Modified Multi CAMShift Algorithm(Modified Multi Continuously Adaptive Mean Shift Algorithm) that extracts skin color area and tracks several human body parts for real-time human tracking system. Skin color area is extracted by filtering input image in predefined RGB value range. These areas are initial search windows of hands and face for tracking. Gaussian background model prevents search window expending because it restricts skin color area. Also when occluding between these areas, we give more weights in occlusion area and move mass center of target area in color probability distribution image. As result, the proposed algorithm performs better than the original CAMShift approach in multiple object tracking and even when occluding of objects with similar colors.

• Tunnel and Underground Space
• /
• v.13 no.6
• /
• pp.455-464
• /
• 2003

Four assessment systems for planning and evaluation of TBM tunnelling are discussed, and their characteristics and input data are analyzed. Two of the systems are determined to be adequate for post-evaluation of TBM performance because the time, such as repair time, downtime, installation time and transport time, must be included for calculations. The others are adequate for pre-planning because the basic data of the systems consist of only the basic properties of rocks and rock masses, and the specification of TBM. In order to apply these assessment systems, a number of equations, graphs and charts are generally required, which seems to be very inconvenient and complicated. In this study, therefore, a user-friendly program operated on Windows system is developed, and each system can be selected by the corresponding input data. It will be possible fer tunnel engineers to select a system according to their objectives and available input data, and to apply the system to TBM tunnel project.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.47 no.4
• /
• pp.63-70
• /
• 2010

In IEEE 802.11e system providing differentiated services, there exist some problems as follows; collision probability increase due to the increase in the number of nodes by employing CSMA/CA transmission mode, transmission speed declining tendency towards the worst of it, which is caused by different transmission mode and decrease of TCP transmission rate as the result of the link occupancy by UDP when TCP shares the link with UDP by the TCP’s flow control characteristic. In this thesis, the initial minimum and maximum CW are set differently according to the number of connected nodes in the network to avoid collisions and TXOP is adjusted according to the channel state, in which ACs with low priority but better channel state will get gradually more chances to transmit leading to optimal channel capacity. Also, by allowing higher priority for ACK frames which control the TCP transmission, the flow control becomes better because that reduces the channel occupancy by UDP flow, and by this, fair transmission is obtained from the result of the more fair transmission and active resource allocation.

• Journal of Digital Convergence
• /
• v.14 no.1
• /
• pp.399-405
• /
• 2016

Head-Up Display, an information-providing display, is a device that provides necessary information through a vehicle window for a driver when driving, with which the driver secures the visibility and acquires information necessary for driving. Head-up displays in early days were mostly installed in imported vehicles but increasingly, being installed in medium and large-sized domestic vehicles, they secures convenience of driving and information acquirement. The information display element of each of currently released brand cars not only has limits in consistency and in displaying interface but also reveals the limitation of a way to apply GUI, being applied to dot reflective form in terms of the technology type. Accordingly, this study draws real time information element described as necessary during driving through case survey and analysis, and aims to provide a user with new GUI guideline through transparent display technology recently developed based on results analyzed with priority of POI(Point of Interest) information.

• Journal of the Korea Convergence Society
• /
• v.3 no.4
• /
• pp.29-34
• /
• 2012

Power window motor assembly including ECU system is important to doors of automobile. This study is done for own development instead of importing of power window motor assembly. This paper is written under five specific subjects. The first, making of prototype sample and analysis of mass-production problem using CAE, the second, design of mass-production mold(2D and 3D), the third, manufacturing of sample mold, the fourth, tryout and measuring of 3 dimensions, the fifth, data analysis and mold modify. In the among them, product sample and analysis of mass-production using CAE, design and manufacture of mass-production mold, and production of sample mold are successfully done. In the results, it is made clear that two cavity and one gate are proper to make a mold of power window motor assembly housing. Besides, it is acquired own technology for mass-production of power window motor.

• Journal of KIISE:Computing Practices and Letters
• /
• v.7 no.4
• /
• pp.299-308
• /
• 2001

The company invests its time and money for temporary maintenance to satisfy the fast change of the computer use environment and the user's demands. Therefore, various problems occur including low performance because of duplication of codes and unstable structures from the restructuring and redevelopment. Furthermore, if a developer, who did not participate in initial process of development, wrote additional program codes to upgrade or restructure, it would cause many problems such as lack or lose of development documentation, understanding of documentation and reuse of existing program language. This study, Object-oriented Refactoring Process, suggests that the developers can reuse object unit to overcome the limit of the reusing code. In addition, this paper shows case study to verify our process by adjusting the project called "D2D", which is a case tool for developing windows system from Company D. Our works get positive results such as improvement of system pelfonnance, decreased cost of development and maintenance and optimizing structure and class.