• Title/Summary/Keyword: 초기곡선

Search Result 703, Processing Time 0.025 seconds

Study on TSD Characteristics of LiF ( Mg , Cu , P ) Single Crystal (LiF ( Mg , Cu , P ) 단결정의 TSD 특성에 관한 연구)

  • 도시홍
    • Journal of the Korean Society of Fisheries and Ocean Technology
    • /
    • v.26 no.1
    • /
    • pp.8-13
    • /
    • 1990
  • The microscopic relaxation parameters for the single crystal were measured by using thermally stimulated depolarization (TSD). Initial rise method, various heating rate method and total glow peak method were used for the determination of the activation energy and Debye relaxation time from TSD glow curves. Activation energy, pre-exponential factor and relaxation time for impurity-vacancy dipole reorientation were 0.55eV, 1.97$\times$10 super(-12) sec and 12.19sec in average, respectively. Dielectric dissipation factor for the crystal was calculated from the measured TSD glow curve, its value being about 3$\times$10 super(-2).

  • PDF

Study on the Generalization of the Equivalent Point Method for Thermal Evaluation (Equivalent Point Method의 일반적 이용을 위한 연구)

  • Rhim, Jong-Whan
    • Korean Journal of Food Science and Technology
    • /
    • v.22 no.5
    • /
    • pp.575-581
    • /
    • 1990
  • The existence of the equivalent point for a thermal processing system was demonstrated using arbitrarily chosen ideal direct heating curves. i.e. isothermal heating curves at $120^{\circ}C$ for 10min and at $135^{\circ}C$ for 10sec. Under these conditions, G-values and F-values were calculated at various values of Ea- and z-values by applying the Arrhenius and the Bigelow models respectively. The equivalent time and equivalent temperature were determined by both line intersection and linear regression methods. The equivalent points estimated by both the line intersection and the linear regression methods were consistent and their values were the same as the heating time and temperature of the ideal direct heating curves.

  • PDF

Numerical Simulation the Effect of Stormwater Treatment on the Water Quality Improvement in a Small Reservoir (초기우수처리에 따른 소규모 저수지 수질개선 효과 수치모의)

  • Ye, Lyeong;Liu, Huan;Lee, Heung-Soo;Kim, Yu-Kyung;Chung, Se-Woong
    • Proceedings of the Korea Water Resources Association Conference
    • /
    • 2007.05a
    • /
    • pp.2064-2068
    • /
    • 2007
  • 합류식 하수도는 오수와 우수를 동시에 배제하는 하수관거 시스템으로 시공이 쉽고 건설비용이 저렴한 반면에 강우시 차집되지 않고 월류되는 유출량으로 인해 수체에 악영향을 초래한다. 관거에서 유출되는 유출수는 강우 초기에 유역에서 집중적으로 유출되는 비점오염원과 하수 및 관거내 오염물질 등을 동반하여 수질 개선을 어렵게 하고 수질 악화를 가중시킨다. 본 연구에서는 기존 유역에 설치된 합류식 하수관거를 분류식으로 개선하고 강우시 초기 세척에 의해 유입하는 비점오염원을 삭감하기 위한 초기우수 처리시설 설치에 따른 M 저수지 수질개선 효과를 수치모델을 사용하여 모의하였다. 저수지의 수질예측은 횡방향 평균 2차원 저수지 수리 및 수질모델인 CE-QUAL-W2를 사용하였다. 저수지 유입량은 군산기상대에서 관측한 일별 강우량 자료를 이용하여 일별 유출량을 산정하였고, 댐 방류량 자료는 M저수지의 2006년 일별 관측수위를 이용하여 유입량과 수위-체적 곡선으로부터 산정하였다. 모델의 보정은 2005년 5월과 8월에 측정한 수질자료를 이용하여 수행하였으며, 저수지의 관측값과 모의결과는 저수지 중앙부 대표지점에서 이루어졌으며, 모델은 관측값을 잘 반영하였다. 모의 결과 M 저수지의 연평균 BOD농도는 합류식(1.25 mg/L)에 비해 분류식 하수 관거(0.91 mg/L)를 도입할 경우 27.2% 개선되었으며, 초기우수 처리시설(0.84 mg/L)을 추가 할 경우 32.8%까지 개선효과가 상승하였다. 기존 합류식 하수관거의 경우 연간 유출부하량은 7,713 kg/yr이었으며, 분류식으로 전환할 경우 2,256 kg/yr, 초기우수처리시설을 추가할 경우 902 kg/yr로 삭감되는 것으로 예측되었다. 분류식하수관거와 초기우수처리를 모두 이행할 경우, BOD와 COD 기준이 호수 수질 기준 II등급 이내로 유지되며, T-P 농도는 0.02mg/L 이하로 유지되어 6월 이후 여름철에 저수지내 조류성장 억제에 효과가 클 것으로 예측되었다. 하수관거 정비사업을 통해 M 저수지는 기존의 농업용 저수지의 목표수질뿐만 아니라, 친수공간으로써 적합한 II등급 수질을 유지할 수 있을 것으로 판단되었다.

  • PDF

Estimation of MFFn for Paddy fields (논지역의 초기세척비율(MFFn) 산정)

  • Choi, Dong Ho;Yoon, Kwang Sik;Baek, Sang Soo
    • Proceedings of the Korea Water Resources Association Conference
    • /
    • 2015.05a
    • /
    • pp.542-542
    • /
    • 2015
  • 비점오염원은 기상조건과 토지이용에 따라 시간에 따른 오염부하량의 변동폭이 크게 발생하며, 강우초기에 오염물질의 농도가 크게 나타난다. MFFn은 강우지속시간에 따라 다양하게 변화하는 오염물질의 부하량과 유출량을 특정시점에서 강우유출율과 오염물질 유출율을 계산할 수 있으며, 강우가 시작될 때 0, 종료될 때 1의 값을 나타내며, 1보다 크면 초기세척이 있음을 나타낸다. 예를 들면 MFF20에서 평균값이 2.5이면 초기우수유출수의 부피 20%에 오염물질 부하량의 부피 50%를 포함하는 것을 의미한다. 본 연구에서는 논에서의 초기세척비율 정량화하기 위해 영산강수계 논지역(이하, 학야지구)과 섬진강수계 논지역(이하, 적성지구) 각 1개유역을 선정하여 2009년부터 2012년까지 수문 및 수질 모니터링을 수행하였다. 유역면적은 학야지구는 13.69 ha 이며, 적성지구는 8.06ha 이다. 두 지역 모두 외부유입이 없으며, 배수로가 구조물화 되어 있어 관측이 용이한 지점이다. 논에서 강우시유출되는 오염물질을 산정하기 위해서 배수로 말단에 압력식 수위계와 자동채수기를 설치하여 일정간격으로 관측하였으며, 수위별 유량관측을 통해 수위-유량관계곡선식을 산정 후 유량으로 환산하였다. 채취된 수질은 수질공정시험법을 통해 BOD, COD, TOC, T-N, T-P, SS를 분석하였으며, 관측된 유량과 수질자료를 이용하여 부하량을 산정하고, MFFn을 이용하여 초기세척비율을 정량화 하였다. BOD COD, TOC, T-N, T-P, SS 의 논 초기세척비율은 n 값이 10% 때 중앙값이 각각 1.3, 1.18, 1.13, 1.2, 1.13, 1.1 였으며, 13%, 11.8%, 11.3%, 12%, 11.3%, 11% 가 유출되는 것으로 나타났으며, n 값이 20%일 때 1.3, 1.1, 1.1, 1.25, 1.2, 1.2 이였으며, 26%, 22%, 22%, 25%, 24%. 24%가 유출되는 것으로 나타났다. n 값이 30%일 때 1.25, 1.0, 1.0, 1.25, 1.13, 1.3 였으며, 37.5%, 30%, 30%, 37.5%, 33.9%, 39%가 유출되는 것으로 나타났다.

  • PDF

A study on the optimal value for the towers height of the ropeway (가공색도의 지주높이 최적치에 관한 연구)

  • 최선호;박용수
    • Transactions of the Korean Society of Mechanical Engineers
    • /
    • v.12 no.2
    • /
    • pp.381-388
    • /
    • 1988
  • The heights of the towers of a ropeway are theoretically derived and the result is experimentally verified. The accuracy in the equation of deflection angle obtained by applying the characteristics of catenary curve was confirmed through experiment. By applying these equations the optimal values of the tower heights could be obtained because the deflection angles trade off each other. The deflection angle was measured by using the curve fitting technique.

Simplified Evaluation Method for Residual Bond Strength of Reinforced Concrete Using Standard Fire Curve (표준화재곡선을 이용한 잔존부착강도 평가 간략방법 제안)

  • Moon, Do-Young
    • Journal of the Korean Society of Hazard Mitigation
    • /
    • v.10 no.5
    • /
    • pp.41-47
    • /
    • 2010
  • For the enhancement of structural safety of thermally damaged reinforced concrete structure, rapid evaluation of damage in the structure is very important. This study addresses a simplified method which is equivalent to the standard fire curve (ISO 834) for the residual bond strength evaluation. In the proposed method, a exposure duration as well as the maximum temperature can be considered. For the comparisons with conventional methods, concrete properties obtained from the report of Daegu subway fire accident were referred and the results support the applicability of the proposed method in this study.

Economics analysis for life cycle cost design of bridges (LCC를 고려한 교량의 경제성 분석)

  • Shin, Yung-Seok;Pack, Jang-Ho;Ahn, Sung-Chan
    • Proceedings of the Computational Structural Engineering Institute Conference
    • /
    • 2010.04a
    • /
    • pp.162-165
    • /
    • 2010
  • 합리적인 교량 대안선정을 위해서는 설계 시 경제성, 경관성, 안전성 및 기능성, 유지관리 용이성, 시공성 등 다양한 속성을 고려하여야 한다. 이 중 경제성은 초기비용뿐만 아니라 공용수명에 걸쳐 발생하는 유지관리비용, 보수 보강비용, 해체 폐기비용 등의 합인 총 생애주기비용에 대해 최소의 비용으로 최상의 가치를 창출하도록 하여야 한다. 본 연구에서는 건설계획과정에서 대표적으로 고려될 수 있는 대안으로 세 가지 교량 형식(강상자형교, 소수주형교, PSC-I형 거더교)을 대상구조물로 선정하고 교량의 공용수명은 상태등급곡선으로부터 추정한 내하율 곡선을 사용하여 산정하였다. LCC최적설계를 위해 설계변수, 제약조건, 목적함수를 구성하였고, 총 생애주기비용을 공용수명으로 나눈 연간생애주기비용을 사용하여 하여 합리적인 교량의 경제성 분석을 수행하였다.

  • PDF

Variation of time-dependent convection beat transfer coefficients in beat transfer analysis at various initial beating rates of tunnel fire scenarios (요소제거모델을 활용한 열전달해석에서 터널 화재이력곡선의 초기가열구배에 따른 대류열전달계수의 변화)

  • Choi, Soon-Wook;Chang, Soo-Ho;Lee, Jun-Hwan;Ahn, Sung-Yol
    • Journal of Korean Tunnelling and Underground Space Association
    • /
    • v.12 no.3
    • /
    • pp.223-237
    • /
    • 2010
  • The initial heating rate is well known as one of the most influencing factors on the occurrence of spalling and the loss of strength in concrete after fire initiation. In this study, a series of fire tests were carried out at different initial heating rates to find out its effects on the deterioration of tunnel structural members. Heat transfer analyses combined with an element elimination model were also carried out to verify its applicability in the same conditions as the fire tests. Moreover, the convection heat transfer coefficients compatible with fire test results were derived from parametric studies. In this course, their time-dependent variations were also analyzed at different initial heating rates. Finally, a numerical formula to estimate the heat transfer coefficients at the various initial heating rates was proposed by the interpolation of the results of numerical analyses.

Evaluation of Modified Design Fire Curves for Liquid Pool Fires Using the FDS and CFAST (FDS와 CFAST를 이용한 액체 풀화재의 수정된 디자인 화재곡선 평가 연구)

  • Baek, Bitna;Oh, Chang Bo;Lee, Chi Young
    • Fire Science and Engineering
    • /
    • v.32 no.2
    • /
    • pp.7-16
    • /
    • 2018
  • In this study, the previous design fire curve for fire simulation was modified and re-suggested. Numerical simulations with the FDS and CFAST were performed for the n-heptane and n-octane pool fires in the ISO 9705 compartment to evaluate the prediction performances of the previous 1-stage and modified 2-stage design fire curves. The numerical results were compared with the experimental temperature and concentrations of $O_2$ and $CO_2$. The FDS and CFAST simulations with the 2-stage design fire curve showed better prediction performance for the variation of temperature and major species concentration than the simulations with 1-stage design fire curve. Especially, the simulations with the 2-stage design fire curve agreed with the experimental temperature more reasonably than the results with the 1-stage design fire curve. The FDS and CFAST simulations showed good prediction performance for the temperature in the upper layer of compartment and the results with the FDS and CFAST were similar to each other. However, the FDS and CFAST showed poor and different prediction performance for the temperature in the lower layer of compartment.

Growing Stage of Sugar Beet at Different Locations in Korea (지역별 사탕무우 생육과정에 대한 고찰)

  • Se-Ho Son
    • KOREAN JOURNAL OF CROP SCIENCE
    • /
    • v.4 no.1
    • /
    • pp.109-114
    • /
    • 1968
  • In order to investigate the growth pattern of sugar beet in Korea, this experiment was conducted using variety GW 359 at Tae-kwan-ryong, Suwon and Cheju. The results are summarized as follows; 1. At Tae-kwan-ryong, early growth stage was relatively long and during higher growing stage plants showed resistance to leaf spot disease, and vegetative maturing started from about September 15th. Top and root growth showed normal curve but it is considered that the early maturing variety will reduce the early growing period and prolong the vegetative maturing period. 2. At Suwon, the growth of top part was favorable until late of July but hereafter leaf spot disease brought death to the 25-35 leaves of top part and regenerated again in October. Consequently, sugar content of root showed changes from decrease to increase. Root weight increased from July to harvest season continunousely but showed abnormal growing curve. This indicates that Suwon is not proper place for sugar beet cultivation. 3. At Cheju, early growing stage was shorter about 15 days than that of Tae-kwan-ryong. Normal growth and long-maturing days favored the sugar accumulation in roots. But it is necessary to introduce non-bolting variety in autumn-winter season culture. 4. Sugar beet could be cultivated economically at Tae-kwan-ryong with 600-800 meter altitude for summer crop and at Cheju for winter crop, but Suwon is considered to be unfavorable for sugar beet.

  • PDF