• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.10
• /
• pp.941-946
• /
• 2010

This study aims to investigate the effects of soybean biodiesel fuel on exhaust emissions with regards to two combustion modes: conventional combustion(existence of PM-NOx trade-off behavior) and low temperature combustion(LTC) in a 1.7 L common rail direct injection diesel engine. As compared to conventional combustion, LTC was achieved by adopting a heavier exhaust gas recirculation and strategic injection parameter optimization. Two sets of fuels, i.e. ultra low sulfur diesel(ULSD) and 20% volumetric blends of soybean biodiesel with ULSD(B20) were used. Regardless of the fuel type, in LTC the simultaneous reduction of PM and NOx was observed and both levels were significantly lower than in case of conventional combustion. Under the given engine operating condition in the case of conventional combustion, B20 produced less PM and more NOx than ULSD. In the case of LTC combustion, B20 produced more PM and NOx than ULSD.

• Journal of the Korean Institute of Gas
• /
• v.3 no.3 s.8
• /
• pp.23-28
• /
• 1999

Variation of explosion characteristics by the blocks in closed vessel was investigated to analyse the effect of the block volume(volume blockage) and the surface area of the blocks(ratio of block surface area to vessel volume). Volume and surface area of blocks in explosion vessel were changed by the combination of blocks. The volume of explosion vessels was 270 liter, and the LPG-air or NG-air mixtures were ignited by the electric spark. Explosion pressure was measured with the strain type pressure transducer. From the experimental results, explosion pressure was decreased by the increase of the volume blockage and the block surface area. And the decrease of explosion pressure was more affected by the volume blockage than the surface area.

• Fire Science and Engineering
• /
• v.20 no.4 s.64
• /
• pp.33-41
• /
• 2006

Nowadays in Korea, KS F 2271(Testing method for incombustibility of internal finish material and element of buildings) has been using for the evaluation of fire safety performance of sandwich panels. The test method in Japan and in Korea was based on the same way. When the Japanese standard building code was revised in 2000, the test method in the ISO 5660-1 was adopted for the test method for combustion performance of internal finishing materials and elements of buildings. According to this, the revision version of draft substituting the test method in the KS F 2271 for one in the ISO 5660-1(Cone Calorimeter method) is informed in Korea. In this study, combustion properties of sandwich panels were tested using the cone calorimeter method. Ignition time, peak heat release rate and total heat released of four sandwich panels and four core materials (thermal insulation material), which are widely used in Korea, were tested. Test results were analyzed for each specimen. Finally, test results were classified by Japanese standard building code and Canadian NBC revised.

• Analytical Science and Technology
• /
• v.21 no.3
• /
• pp.159-166
• /
• 2008

In this study, the characteristics of emulsified fuel and engine emissions were studied. Emulsified fuel which composed of water and diesel was manufactured by using homogenizer and ultrasonic generator. Engine emissions were studied whit engine dinamometer. In emulsified fuel, density and viscosity were increased with increasing water contents, but viscosity was decreased over 60% of water in emulsion fuel. The emulsion type of W/O changed to that of O/W over 60% of water in emulsion fuel. In the results of engine dinamometer test, NOx concentration and smoke density were reduced with increasing water contents in emulsified fuel but reciprocal in the case of THC, CO. Temperature and power were reduced with increasing water contents in emulsion fuel. In conclusion, it seemed that using emulsified fuel for diesel engine was effective for reducing NOx concentration and smoke density.

• Journal of Radiation Protection and Research
• /
• v.22 no.1
• /
• pp.9-14
• /
• 1997

Chitosan, a natural nontoxic chelator, was reported to reduce whole body retention of radiostrontium in mice. As calcium has a simillar chemical properties to strontium both of which be easily bound with hydroxyapatite structure, calcium can be either a competitor or enhancer to chitosan on the removal of radiostrontium. We compared the effect of chitosan and calcium on the excretion of ingested radiostrontium ($^{85}$Sr). Chitosan or calcium($Cacl_2$) and usual food was mixed as 1:99 by weight. The mixed food to chitosan (group 1) or calcium (group 2) were given orally for 30 days before $^{85}$Sr administration. In other groups, mixed calcium and chitosan solution (group 3), 1% calcium (group 4), or 1% chitosan solution (group 5) was given for 7 days immediately after oral administration of $^{85}SrC1_2$ ($0.25{\mu}Ci$). In control group, no chitosan or calcium were given. Either chitosan or calcium was effective on the removal of $^{85}Sr$ from mouse body(Table. 1). Addition of calcium on chitosan did not improve or deteriorate the effect of chitosan on the removal of $^{85}Sr$ from mouse body. In conclusion, calcium was similarly effective on the removal of $^{85}Sr$ from mouse body.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.197-197
• /
• 2010

음식물쓰레기의 삼성분은 수분, 휘발분, 회분이며 이들이 차지하는 비율은 계절, 지역별로 다소 상이하지만 수분 약 80%, 회분3%, 휘발분 17%이다. 음식물쓰레기 전처리과정으로 이물질제거, 탈수공정이 있으며 탈수공정에서 다량의 탈리액이 발생한다. 본 연구에서는 탈리액을 데칸타를 이용하여 1차로 원심분리하여 고.액 분리한 액을 실험대상으로 하였다. 실험대상 탈리액의 물성은 BOD 78,800[mg/l], COD 41,000[mg/l], 부유물질 25,900[mg/l], 총질소 928[mg/l]이었다. 탈리액에는 기름성분(육류, 식용유등), 입자상물질등이 포함되어 있으며 이들은 난분해성 유기물질로, 이를 제거하는데 기존의 처리방법으로 많은 어려움이 있어 주요한 수질오염 발생원이 되고 있다. 예를들면 하수처리장 폭기조 수면에 유막을 형성하여 산소공급을 방해함으로 미생물번식을 방해하는 요인이 된다. 본 연구는 음식물쓰레기 탈리액의 수분, 고형분, 유분으로의 삼상분리에 관한 것이다. 유분은 에멀젼형태로 안정되게 수층에 분산되어 존재한다. 미세기포를 이용한 부상법의 경우 미세기포 표면과 유분의 화학적친화력이 낮아 기포표면에 유분이 잘 부착되지 않으며, 원심분리 방법만으로는 유분 분리효율이 낮고, 추출에 의한 분리시 추출액이 다량 소요되고 처리시간이 길며 추출액 비용이 많이 소요된다. 탈리액을 유분, 슬러지, 수분으로 분리하면 환경오염을 일으키는 주요성분을 신재생에너지 원료로 활용할 수 있다. 유분의 주성분이 동식물성 유지이므로 전처리시 산촉매를 이용 수분과 유리지방산을 제거하고 염기성촉매를 이용하여 전이에스테르화 반응을 거치면 바이오디젤인 FAME과 글리세롤으로 변환하므로 글리세롤을 분리하면 바이오디젤을 얻을 수 있다. 슬러지는 입자상 물질로 착화가 잘 되고 건조하면 발열량이 높으며 중금속등에 오염되지 않아 청정연료로 활용이 가능하다. 실험실에서의 탈리액 삼상분리방법은 다음과 같다. 탈리액 30ml당 추출액으로 노말헥산을 1ml를 가한 다음 플라스크에서 $80^{\circ}C$로 가열 후 방냉한다. 가열중 노말헥산의 손실을 방지하기 위하여 증발가스를 콘덴서에서 응축하여 플라스크로 재순환한다. 탈리액을 플라스크에서 꺼내어 원심분리기 rack에 300-400g씩 병에 각각 넣고 4,000rpm으로 30분간 운전한다. 탈리액은 상부로부터 유분층, 미세입자층, 수층, 슬러지층으로 분리된다. 각 층의 계면에서 2종의 성분이 약간 섞일 수 있다. 유분을 분리한 후 유분층 잔존물과 미세입자층, 수층 상층부의 혼합물을 취하여 50g씩 병에 넣고 3,500rpm으로 10분간 운전한 후 유분을 분리한다. 마지막으로 미세입자층만을 3,500rpm으로 10분간 원심분리한 후 유분을 따로 분리한다. 얻어진 유분은 rotary evaporator에서 $120^{\circ}C$로 가열하여 유분과 노말헥산을 분리하며 분리효율을 제고하기 위하여 감압하에서 운전한다. 분리된 유분의 고위발열량이 9,450[Kcal/kg]이었으며 원소분석 결과 탄소 74.7%, 수소 12.55%, 질소 0.08%, 유황분 0.0003%이었다. 분리된 유분의 양은 계절별로 시료별로 다르며 가을철에는 1.6-1.9%, 여름철은 1.0-1.3%이었다. 분리된 슬러지로부터 Hg, As, Cr, Cd, Pb 중금속 성분이 검출되지 않았으며 수분 2.8%, 휘발분 76.85%, 회분 7.52%, 고정탄소 12.83%이었고 원소분석결과 탄소 45.25%, 수소 7.46%, 질소 5.05%, 산소 34.39%, 유황분 0.33%이었으며 저위발열량은 4,480[Kcal/kg]이었다. 분리된 슬러지 양은 11-19% 이었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.11
• /
• pp.1065-1072
• /
• 2012

Due to its oxygen (O) content, biodiesel (BD) is advantageous in that it lowers PM emissions in CI engines. Therefore, BD is considered one of the best candidates for low temperature combustion (LTC) operation because its use can extend the regime for simultaneous reduction of PM and $NO_x$. Thus, in this study, LTC operation was realized using BD and diesel with a 5~7% $O_2$ fraction. Engine test results show that the use of BD increased the efficiency and reduced emissions such as PM, THC, and CO; furthermore, IMEP reduced by 10~12% owing to the lower LHV of the fuel. In particular, smoke was suppressed by up to 90% because O atoms in the BD enhanced the soot oxidation reaction. To compensate the IMEP loss, turbocharging (TC) was then tested, and the results showed that the power output increased and PM was reduced further. Moreover, TC in BD engine operation allowed a similar level of reduction in both $NO_x$ and PM at 11~12% $O_2$ fraction, suggesting that there is a potential to widen the operating range by the combination of TC and BD.

• Journal of Energy Engineering
• /
• v.19 no.2
• /
• pp.136-142
• /
• 2010

Combustion reactivity and thermal behavior of two imported coals used as a pulverized fuel of commercially thermal power plant were investigated by thermogravimetric analysis (TGA) and large scale test furnace of 200 kg/hr. TGA results showed that combustion efficiency of high moisture coal has lower than reference coal due to the slow combustion completion rate although it has the low ignition temperature, and activation energies of high moisture coal with 79 kJ/mol for overall combustion was higher than reference coal of 53 kJ/mol. Test furnace results ascertained that flame of black band of high moisture coal during the combustion in boiler broke out compared to reference coal and then it becomes to unburned carbon due to the less reactivity and combustion rate. But, Blending combustion of high moisture coal with design coal of high sulfur are available because sulfur content of high moisture coal was too low to generate the low SOx content in flue gas from boiler during the combustion. The ash analysis results show that it was not expected to be associated with slagging and fouling in pulverized coal fired systems due to the low alkali metal content of $Na_2O$ and $K_2O$ compared to bituminous coal.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.7
• /
• pp.722-728
• /
• 2015

The demand for shipboard energy management is expected to gradually increase based on ship energy efficiency management plans (SEEMPs), which have been in use since January 1, 2013. Therefore, the fuel consumption of the main engine, which occupies the greatest portion of the energy used, along with elements related to the engine power, should be strictly monitored. There are many different methods for indicating the engine power. However, this study performed an experiment to monitor the status of a ship's engine power in real time using an encoder and a proximate switch, which are economical to purchase and easy to install. In the experiment, the angular velocity during one cycle of a two-stroke low-speed engine was measured, and the measured data were converted to the torque fluctuation. The angular velocity during an abnormal firing condition in the cylinder was also measured, and the torque fluctuation as a result of a misfire was considered. The results were compared with sea trial data to determine the reliability. In this study, the status of the engine power was determined using the torque fluctuation of the main engine in an operating ship.

• Journal of Bio-Environment Control
• /
• v.8 no.2
• /
• pp.75-82
• /
• 1999

This study was carried out to examine the effect of day/nignt temperatures during seedling culture on the vegetative and reproductive growth of Lycopersicum esculentum ‘Seokwang’. The study was consisted of two culture stages, plug seedling production in the growth chamber and hydroponic culture of the plant in a glasshouse. Experiments were replicated over time. The germinated seedlings were raised for 33 days (experiment 1) and 35 days (experiment 2) in 4 growth chambers, each with day/night temperatures of either $25^{\circ}C$/$25^{\circ}C$, 16$^{\circ}C$/16$^{\circ}C$, 16$^{\circ}C$/$25^{\circ}C$ or $25^{\circ}C$/16$^{\circ}C$. Cool-white fluorescent lamps provided 140$\mu$mol.m$^{-2}$ .s$^{-1}$ light for 12h each day. In the second experiment, all chambers were supplied with 1000$\mu$mol.mol$^{-1}$ CO$_{2}$ during the photoperiod and had an air velocity of 0.3m.s$^{-1}$ and relative humidity of 80%. Plug seedlings raised were transplanted to rockwool slabs in a glasshouse and were grown hydroponically using the same nutrient solutions used for seedling culture for 37 days (experiment 1) and 35 days (experiment 2). Plant height was affected more by mean daily temperature than by interaction of day and night temperatures. Plant height was the highest in 16/16$^{\circ}C$ treatment. Leaf count was not affected by day and night temperatures, and the chlorophyll concentration was the highest in 16/$25^{\circ}C$ treatment. Fresh and dry weights of stem tended to be greater in treatments of constant day and night temperature. The number of node on which first and second flower clusters were set was significantly higher in 25/$25^{\circ}C$ treatment than in the other treatments. Days to flower of the first flower on the first flower cluster were the greatest in 25/$25^{\circ}C$ and the least in 16/$25^{\circ}C$ treatment. Vegetative and reproductive growth, such as height, fresh and dry weights, days to flower, and nodes of the 1st and 2nd flower cluster set were affected by day/night temperatures.