• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.92-102
• /
• 2020

Porous pavement (PP) has attracted attention as a new alternative measure against road traffic noise. PP refers to pavement that reduces the fines in the asphalt mixture to form voids. These voids can reduce traffic accidents and friction noise. For active application, verification of the noise reduction effect is required. In this study, the noise reduction of single-layer PP(SLPP) and double layer PP(DLPP) was analyzed. First, the Sejong section was selected, and traffic noise was measured using the SPB method on the roadside. The traffic volume, speed, and mixing ratio of large vehicles were measured. As a result, the DLPP was evaluated to be 7.95 dB(A) smaller on average and 7.57dB(A) smaller at the 95% reliability level than the SLPP. The traffic volume was more influential than the speed and the mixing rate of large vehicles. As the traffic volume increased, the noise increased, but the difference in noise between the two pavements decreased gradually. The results showed that the most effective way to reduce road traffic noise is to change the road pavement rather than reduce traffic speed, restrict traffic for heavy vehicles, or reduce traffic volume.

• Journal of Wetlands Research
• /
• v.9 no.3
• /
• pp.43-49
• /
• 2007

A ditch is a facility for managing washed-off runoff from parking lot area. Washed-off runoff inflows into ditches where it is retained for a short period of time. At this point, it is assumed that a ditch is a preliminary unit for runoff treatment. This research carries out the distribution of particle size and chemical compound for sediment in parking lot ditch. This work is important to understand the amount of generated sediment from this area to be able to determine different particle size ranges for treatment. Metal concentrations for sediment according to particle size are analyzed. From the distribution of particle size, the weight ratio with the range of $425-850{\mu}m$ is the highest. Considering its weight ratio, the metal concentration of coarser particles is high, otherwise metal concentration increases as particle size decreases. Metal load of the range is higher and the ratio of total metal load in the case of Cu, Pb, Zn is nearly 30%. Moreover metal concentration associated with particle size depends on particle ratio. To manage non-point source pollution for parking lot area, these results can be used with this ditch unit.

• Journal of Korean Society for Atmospheric Environment
• /
• v.29 no.5
• /
• pp.656-667
• /
• 2013

The non-exhaust coarse, fine, and ultrafine particles were characterized by on-road driving measurements using a mobile sampling system. The on-road driving measurements under constant speed driving revealed that mass concentrations of roadway particles (RWPs) were distributed mainly in a size range of 2~3 ${\mu}m$ and slightly increased with increasing vehicle speed. Under braking conditions, the mode diameters of the particles were generally similar with those obtained under constant speed conditions. However, the PM concentrations emitted during braking condition were significantly higher than those produced under normal driving conditions. Higher number concentrations of ultrafine particles smaller than 70 nm were observed during braking conditions, and the number concentration of particles sampled 90 mm above the pavement was 6 times higher than that obtained 40 mm above the pavement. Under cornering conditions, the number concentrations of RWPs sampled 40 mm above the pavement surface were higher than those sampled 90 mm above the pavement. This might be explained that a nucleation burst of a lot of vapor evaporated from the interaction between the tire and the road pavement under braking conditions continuously occurred by cooling during the transport to the sampling height 90 mm, while, for the case of cornering situations, the ultrafine particle formation was completed before the transport to the sampling height of 40 mm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.174-182
• /
• 2014

Recently, not only common types of hybrid electric vehicle (HEV) such as series or parallel but many other types of HEVs including 4WD hybrid electric vehicle have been developed and released. In this study, analysis of fuel economy and driving performance for 2WD and 4WD HEV are conducted using backward simulation based on dynamic programming. To analyze the characteristics of 4WD HEV, tire slip model based on vehicle dynamics was applied to the backward simulation program. As a result, 2WD HEV shows better fuel economy than 4WD HEV because of relatively simple configuration. However, in a severe road condition, 4WD HEV shows better driving performance that 2WD HEV had about 6% of impossible time to follow the driving cycle though the 4WD HEV had no impossible time.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.197-197
• /
• 2011

최근 들어 전력 사용량의 증가로 인한 화력발전소의 부산물인 석탄회 중 바텀애시와 각종 공공사업과 관련하여 해마다 현장발생토의 발생량이 지속적으로 증가하고 있는 추세이다. 바텀애시와 현장발생토사를 효과적으로 재활용하는 방법 중 유동성 뒤채움재를 개발하여 활용하는 방안을 모색하기 위한 연구이다. SP로 분류된 흙 현장발생토와 서천 화력발전소에서 발생하는 석탄회 중 입경이 0.9~1.5mm의 바텀애시만을 선별하여 현장발생토와 바텀애시의 비율을 7 : 3으로 변환한 최적배합을 선정하여 강재로 제작된 가로 80cm, 세로 60cm, 높이 90cm의 모형토조를 이용하여 실험을 진행하였으며, 사용상 지하 매설이 되는 관의 거동 특성은 확인하기 위하여 내경 30cm, 두께 8mm의 연선관 중 하나인 PVC관을 원형지하매설관으로 선정하여 배합을 타설하는 과정과 타설 후 7일간의 양생기간을 거친 후 차량하중으로 가정할 수 있는 하중을 가하여 원형지하매설관의 관외부에서 수직방향과 수평방향의 토압과 관내부의 수직 수평방향 변위 그리고 관 자체의 횡 종단 변형을 측정하여 원형지하매설관의 거동특성을 파악하였다. 타설시 지하매설관은 유동성 뒤채움재의 특성으로 인하여 시간이 지남에 따라 안정화되는 것을 확인할 수 있었으며, 최대하중을 3300kgf로 하여 하중 재하 후 지하매설관의 거동특성은 대체적으로 일반 모래를 사용하여 실험한 값보다 적은 변형 특성을 보이고 있으나 수평토압의 경우 일반적인 흙의 변형과 전혀 상이한 결과값을 보이는 경우도 있어 추가적인 실험 및 고찰의 필요하다. 본 실험에서 사용한 최적배합비 이외의 배합으로 같은 실험을 수행하여 바텀애시 량의 가감 및 재활용 재료인 폐타이어 고무칩등을 첨가한 실험을 계획하고 있으며 추후 실내시험과 모형실험을 토대로 유한요소해석을 추가로 시행하여 실험값과 해석값의 비교를 할 예정이다.

• Transactions of the KSME C: Technology and Education
• /
• v.2 no.1
• /
• pp.9-13
• /
• 2014

Nowadays, among several reasons for customers to choose their own cars, NVH performance plays much important role. The concern for the car interior noise is increasing recently, because electric cars and hybrid cars generate less engine noise which was the main noise of traditional cars. According to oversea references, high Lateral Dynamic Stiffness (LDS) of vehicle wheels is described to reduce Structure Bone Noise (SBN) which is being generated while driving cars. However availablet test standards and test results are not enough, in this study the interior noise has been measured after attaching a same tyre to several wheels which has different Lateral Dynamic Stiffness. The test has verified that the interior noise differs depending on Lateral Dynamic Stiffness of wheels. As to this, the reduction of the interior noise can be possible with the optimal design of the wheel.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.125-130
• /
• 2013

According to the law revision of TPMS mounting obligations in Korea, researches about energy harvester which is the alternative of the battery are actively performed by many groups. Because WSN (Wireless Sensor Network) has the proposition of "Install and forget" and the power supplier also has the same performance as the vehicle's lifetime. In this paper, electromagnetic induction type of energy harvester through the relative motion between the rotating wheel and the fixed brake disc is introduced by using the most efficient source as the rotating motion in the view of vehicle's mechanism. The coil on the wheel and the permanent magnet at the brake disc are arranged in several ways. These various arrangements are the number of coil turns are consisted of design variables. By using the orthogonal array to reduce the experimental cost, the optimal composition is verified through the experiment. Finally the validity of the module is considered by measuring the level of storable electrical energy.

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.31-42
• /
• 2013

PURPOSES : The purpose of this study is to eliminate the noise of the vehicle after measuring the friction noise obtained from the NCPX (Noble Close ProXimity) method. The pure friction noise between the tire and road pavement could be determined from filtering the compositeness of sound and the influence of the vehicle noise. METHODS: The noise magnitude could be determined by analyzing the sound pressure level (SPL) and sound power level (PWL) along with the noise frequency of a FFT (Fast Fourier Transform) analysis as well as CPB (Constant Percentage Bandwidth) analysis. RESULTS: When the test for measuring the friction noise originated somewhere between tire and road pavement is performed with NCPX method, it must be fulfilled by attaching the surface microphone near the tire. In this condition, the surface microphone can measure the friction noise occurred at between tire and pavement, the chassis noise from the engine and power transfer units, the fluctuating aerodynamic noise, and the turbulence noise directly affected to the surface microphone. By using the NCPX method, the noise occurred at the vehicle must be eliminated for measuring the friction noise between tire and pavement from the traffic noise. CONCLUSIONS: The vehicle's testing engine noise depends on the vehicle and road types. The effect of vehicle's engine noise is less than the friction noise occurred at between tire and pavement at less than 1% effect.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.105-111
• /
• 2003

Wheel for passenger car support the car weight with tires, and they transmit rolling and braking power into the ground. Whittling away at wheel weight is more effective to boost fuel economy than lighting vehicle body structure. A shape of hole in disk is optimized for minimizing the weight of steel wheel. Pro/ENGINEER program is used for formulating the design model, and ANSYS package is selected for analyzing the design model. It has difficulties to interface these commercial software directly. For Combining both programs, response surface methodology is applied to construct approximation functions for maximum stresses and maximum displacements are obtained by full factorial design of five levels. This steel wheel is modeled in 14-inch diameter of rim, and wide parameter of hole in disk is only selected as design variable for reducing the weight of steel whee. PLBA(Pshenichny-Lim-Belegundu-Arora) algorithm, which used the second-order information in the direction finding problem and uses the active set strategy, is used for solving optimization problems.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.69-78
• /
• 2009

Korea has achieved significant economic growth with building the Gyeongbu Expressway. As the number of new road construction projects has decreased, it becomes more important to maintain optimal status of the current road networks. One of the best ways to accomplish it is weight enforcement as active control measure of traffic load. This study is to develop High-speed Weigh-in-motion System in order to enhance efficiency of weight enforcement, and to analyze patterns of overloaded trucks on highways through the system. Furthermore, it is to review possibilities of developing overweight control system with application of the HS-WIM system. The HS-WIM system developed by this study consists of two sets of an axle load sensor, a loop sensor and a wandering sensor on each lane. A wandering sensor detects whether a travelling vehicle is off the lane or not with the function of checking the location of tire imprint. The sensor of the WIM system has better function of classifying types of vehicles than other existing systems by detecting wheel distance and tire type such as single or dual tire. As a result, its measurement errors regarding 12 types of vehicle classification are very low, which is an advantage of the sensor. The verification tests of the system under all conditions showed that the mean measurement errors of axle weight and gross axle weight were within 15 percent and 7 percent respectively. According to the WIM rate standard of the COST-323, the WIM system of this study is ranked at B(10). It means the system is appropriate for the purpose of design, maintenance and valuation of road infrastructure. The WIM system in testing a 5-axle cargo truck, the most frequently overloaded vehicle among 12 types of vehicles, is ranked at A(5) which means the system is available to control overloaded vehicles. In this case, the measurement errors of axle load and gross axle load were within 8 percent and 5 percent respectively. Weight analysis of all types of vehicles on highways showed that the most frequently overloaded vehicles were type 5, 6, 7 and 12 among 12 vehicle types. As a result, it is necessary to use more effective overweight enforcement system for vehicles which are seriously overloaded due to their lift axles. Traffic volume data depending upon vehicle types is basic information for road design and construction, maintenance, analysis of traffic flow, road policies as well as research.