• Korean Journal of Optics and Photonics
• /
• v.26 no.5
• /
• pp.269-274
• /
• 2015

In this paper we design the optical system for an integrated two-channel TO-type optical transmitter to apply the HDMI interface using the code V simulator. The proposed integrated two-channel optical transmitter has two VCSELs attached in parallel on an 8-pin TO-CAN package, on top of which is a lens filter block ($1mm{\times}2mm{\times}4mm$) composed of hemispherical lenses and WDM filters. Considering two-channel transmitters manufactured with wavelength combinations of 1060nm/1270nm and 1330nm/1550nm, we obtain the optimum value of the diameter of the hemispherical lens as 0.6 mm for both combinations, and the distances L between the lens filter block and ball lens as 1.7 mm and 2.0 mm for the 1060nm/1270nm and 1330nm/1550nm wavelength combinations, respectively. At this time, the focal length f0 of the lens filter blocks for wavelengths of 1060, 1270, 1330, and 1550 nm are 0.351, 0.354, 0.355, and 0.359 mm, respectively, and the focal lengths F of light passing through the lens filter block and ball lens are 0.62 mm for 1060nm/1270nm and 0.60-0.66 mm for 1330nm/1550nm wavelength combinations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.247-255
• /
• 2013

In this paper, a soft switching DC-DC converter for AC module type photovoltaic (PV) module integrated converter is proposed. A push-pull converter is suitable for a low voltage PV AC module system because the step-up ratio of a high frequency transformer is high and the number of primary side switches is relatively small. However, the conventional push-pull converters do not have high efficiency because of high switching losses by hard switching and transformer losses (copper and iron losses) by high turns-ratio of the transformer. In the proposed converter, primary side switches are turned on at zero voltage switching (ZCS) condition and turned off at zero current switching (ZVS) condition through parallel resonance between secondary leakage inductance of the transformer and a resonant capacitor. Therefore the proposed push-pull converter decreases the switching loss using soft switching of the primary switches. Also, the turns-ratio of the transformer can be reduced by half using a voltage-doubler of secondary side. The theoretical analysis of the proposed converter is verified by simulation and experimental results.

• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.509-514
• /
• 2003

Mach-Zehnder interferometric wavelength converters with monolithically integrated semiconductor optical amplifiers (SOA's) have been fabricated and characteristics of wavelength conversion at 10 Gb/s have been investigated for wavelength span of 40 nm. The devices have been achieved by using a butt-joint combination of buried ridge structure type SOA's and passive waveguides. In the integration, a new method has been applied that removes p+InP cladding layer leading to high propagation loss and forms simultaneously the current blocking and the cladding layer using undoped InP. The module packaging has been achieved by using a titled fiber array for effective coupling into the tilted waveguide in the wavelength converter. Using the module, wavelength conversion with power penalty lower than 1 ㏈ at 10 Gb/s has been demonstrated for wavelength span of 40 nm. In addition, it is show that the module can provide 2R (re-amplification, re-shaping) operation by demonstrating the conversion with the negative penalty.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.147-148
• /
• 2012

Recently, hybrid generation systems combine multiple energy sources or storage components to optimize the characteristics of the individual energy sources. In this paper, a battery integrated PV power optimizer for PV-battery hybrid power generation system is proposed. PV system using proposed topology can easily increase battery capacity and remove high power bidirectional converter to control bulky battery bank.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.4
• /
• pp.311-318
• /
• 2020

A photovoltaic (PV) system uses an AC module integrated converter (MIC) to operate PV cells at a maximum power point (MPP) and for high efficiency. The MPP of a PV cell varies depending on partial shading conditions, and loss occurs differently according to the configuration method of the PV-MIC. Therefore, this study compares the losses of passive components and power semiconductors according to the partial shading conditions of the PV module. Theoretical loss analysis is performed using parameters for the datasheet and PSIM simulation results. Analysis results verify that the one-stage PV-MIC demonstrates high efficiency.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.563-564
• /
• 2010

In this paper, photovoltaic module integrated converter (MIC) based on active clamp current-fed half-bridge converter is proposed. The converter stage operates in zero-voltage condition using active clamp technique. The theoretical study and circuit design for proposed inverter are confirmed with PSIM simulator.

• Korean Journal of Optics and Photonics
• /
• v.19 no.2
• /
• pp.122-126
• /
• 2008

Dual backlight unit incorporating a single light source integrated with a beam splitting reflector was demonstrated, providing a surface light beam for both the keypad and the display section simultaneously. The reflector was realized by aligning a groove substrate with a matching cover, and a light guiding module comprising a stack of light guide panels and prism/diffuser sheets was attached to both sides of the reflector. A light emanating from the light source-placed in the middle of the substrate-undergoes a series of reflections through the reflector to reach the input of the light guiding module. Then it is transformed into a surface light beam, which is used to irradiate the keypad and display sections simultaneously. As for the accomplished dual surface light sources, the measured average luminance and the spatial luminance uniformity were respectively about $420\;cd/m^2$ and 69% for the keypad section, and $640\;cd/m^2$ and 79% for the display section.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.6
• /
• pp.471-477
• /
• 2012

In this paper, in order to use module integrated converter using cascaded buck-boost converter for a low battery charger in stand-alone system, a charging algorithm which considers photovoltaic and battery status and PWM controllers which are changed according to charging modes are proposed. The proposed algorithm consists of constant current mode, constant voltage mode and maximum power point tracking mode which enables the battery to charge with maximum power rate. This paper also presents design of cascaded buck-boost converter that is the photovoltaic charger system. A 150W prototype system is built according to verify proposed the charger system and the algorithm.

• Korean Journal of Optics and Photonics
• /
• v.21 no.3
• /
• pp.111-117
• /
• 2010

A 780 nm monolithic individually addressable 8-beam diode laser with 10mW optical power was developed for use in a laser scanning unit. Beam to beam spacing is $30\;{\mu}m$ and an air bridge interconnection process was developed for individual operations. From electrical and optical characteristic measurements, the developed device is a suitable optical source for a high speed laser scanning unit in multi-function printing systems and laser beam printers.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.6
• /
• pp.31-38
• /
• 2009

To improve the image quality and lower the power consumption of the mobile applications, it is the one of the best candidate to control the backlight unit of the LCD module with ambient light. Ambient light sensor and readout circuit were integrated in LCD panel for the mobile applications, and we designed them with LTPS TFT. We proposed noble start-up correction in order to correct the variation of the photo sensors in each panel. We used time-to-digital method for converting photo current to digital data. To effectively merge time-to-digital method with start-up correction, we proposed noble dual slope correction method. The entire readout circuit was designed and estimated with LTPS TFT process. The readout circuit has very simple and stable structure and timing, so it is suitable for LTPS TFT process. The readout circuit can correct the variation of the photo sensors without an additional equipment, and it outputs the 4-levels digital data per decade for input luminance that has a dynamic range of 60dB. The readout rate is 100 times/sec, and the linearity error for digital conversion is less than 18%.