• 소성∙가공
• /
• 제21권6호
• /
• pp.354-359
• /
• 2012

Effects of a nitriding treatment on the tensile and high cycle fatigue properties were investigated by conducting ion-nitriding and gas nitro-caburizing treatments on the spheroidized SCr430B medium-carbon steel and performing tensile and tension-tension high cycle fatigue tests. The nitrided samples showed much lower strength and ductility compared to those in the initial as-spheroidized state and premature fracture occurred at the hardened layers. The micro-voids in the compound layer caused fatigue crack initiation. Thus, the removal of the compound layer with micro-voids remarkably improved the fatigue resistance to even beyond that of the as-spheroidized sample.

• 전자공학회논문지A
• /
• 제31A권9호
• /
• pp.72-77
• /
• 1994

GaAs MISFETs, with photo-CVD grown P$_{3}$N$_{5}$ gate insulator and sulfide treatment, have been fabricated and showed the instability of drain current reduced less than 22 percent for the period of 1.0s~1.0${\times}10^{4}s$. The effective electron mobility and extrinsic transconductance of the device are about 1300cm$^{2}$/V.sec and 1.33mS at room temperature. The C-V characteristics of GaAs MIS Diode and AES analysis are also discussed with respect to effect of sulfide treatment conditions.

• 한국생물공학회:학술대회논문집
• /
• 한국생물공학회 2002년도 생물공학의 동향 (X)
• /
• pp.343-345
• /
• 2002

This study was performed by the airlift bioreactor using the nitrifier consortium entrapped in polyvinyl alcohol(PVA) for removing low concentration total ammonia nitrogen(TAN). At the aeration rate of 1.5 vvm, TAN removal rate and removal efficiency was 316.6${\pm}$7.2 $g/m^3$ day and 92.8${\pm}$2.2%. Removal rate was continuously increased with decreasing from 0.5hr to 0.05hr of hydraulic residence time(HRT), whereas removal efficiency was decreased with decreasing HRT.

• 한국생물공학회:학술대회논문집
• /
• 한국생물공학회 2002년도 생물공학의 동향 (X)
• /
• pp.346-348
• /
• 2002

This study estimated the effect of influent TAN concentration. temperature and pH in the airlift bioreactor(aeration rate; 1.5 vvm, HRT 0.35hr) using immobilized nitrifiers by PVA. At the effect of influent TAN concentration, removal rate was increased with increasing it and removal efficiency maintained 93${\pm}$2%. The optimum temperature for nitrification was $30^{\circ}C$ and at this point. removal efficiency was 95.5${\pm}$1.5%. It was effective to nitrify at $10^{\circ}C$ of low temperature. In the pH range from 7 to 9 in the bioreactor. removal rate and removal efficiency was 310${\pm}$10 $g/m^3$ day and 94${\pm}$3%.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.903-907
• /
• 1996

Under two level block loading, the carbornitrizing specimen can be expected to show different behavior from other uniform material because the properties of surface layer and inner material are different from each other. In this research, the modified Marco-Starkey cumulative theory, which considers load interaction effect, can predict the life of SCM415 carbornitrizing and original notched and smooth specimen, In the low-high test of carbornitrizing specimen which has long life, however, we may additionally consider the increase of life by means of the stress hardening of inner original material.

• 한국정밀공학회지
• /
• 제6권1호
• /
• pp.75-84
• /
• 1989

This paper deals with the effect of $N_2$ and $H_2$gas mixture ratio and ion-nitriding time in the corrosion fatigue fracture behavior of ion-nitrided SCM4 steel with notch subject to rotary bending stress. The specimens were treated rapid water cooling after ion-nitriding at $500^{\circ}C$ Torr for 1 hour and 3 hours in gas mixtures of 80% $N_2$and 50% $N_2$. The fatigue limit and the fracture strength of corrosion fatigue depended on $N_2$gas quantity and ion-nitriding time. The ion-nitrided specimens showed about 88 .approx. 158% increase in the fracture strength of corrosion fatigue in $10^6$ cycles than non-nitrided specimens. The corrosion failure is due to corrosion pitting of the surface, and the propargation of cracks started at the surface into the core.

• 열처리공학회지
• /
• 제23권5호
• /
• pp.269-276
• /
• 2010

This study has been carried out to the low temperature plasma nitriding treatment on the mechanical properties of stainless steel at temperature range between $400^{\circ}C$ and $500^{\circ}C$. It was found that there was precipitated to free CrN matrix below $400^{\circ}C$ and there was precipitated S-phase of STS 316L, ${\varepsilon}$-phase of STS 409L and ${\alpha}N$-phase of STS 420J2. STS 316L has formed relatively abundant CrN phase and ${\gamma}^{\prime}-Fe_4N$ phase at $500^{\circ}C$, alternatively STS 409L and STS 420J2 were more deeply nitrided than STS 316L at $500^{\circ}C$.

• 오토저널
• /
• 제9권2호
• /
• pp.28-33
• /
• 1987

This thesis is to improve the mechanical properties of carbon steel by the ion-nitriding, and post-heat treatment. The structures of ion-nitrided SM45C steel were changed to martensite by quenching from 730.deg. C and 800.deg. C. And then a few of the quenched specimens was tempered at 200.deg. C for 120 min. The emphasis in this study is focussed on Comparison of hardness and fatigue strength with the ion-nitrided steel. The results obtained are summerized as follows. 1. To improve the hardness and fatigue strength of ion-nitrided steels, it is effective to under take diffusion treatment for a short time at the austenite temperature(800.deg. C). 2. If ion-nitrided steel is heated for a long time at high temperature, de-nitriding occure. 3. The quenching treatment after nitriding on the carbon steel is necessary to improve the mechanical properties of the steels.

• 열처리공학회지
• /
• 제16권2호
• /
• pp.71-77
• /
• 2003

We investigate the phase formation in the compound layer of cast irons during the gaseous nitrocarburising of four different cast irons, that contain different types of graphites in the shape and size. We examine the change in the surface roughness with the nitrocarburising time. The observation of cross-sectional microstructure and X-ray diffraction analysis indicate that the compound layer consists of single ${\varepsilon}-Fe_{2-3}(N,C)$ phase and that its thickness increases in a parabolic manner with the treatment time. The surface roughness parameters, Rz and Ra increase with increasing treatment time. In other words, the roughness parameters increase as the thickness of compound layer increases. The parameters also depend on the shape and size of graphite in the individual cast irons.

• 열처리공학회지
• /
• 제23권3호
• /
• pp.142-149
• /
• 2010

Austenitic stainless steel is more or less difficult with conventional gas nitriding treatment, but it can be nitrided after appropriate pre-heat treatment. The pretreatment was more effective upon nitriding for austenitic stainless steel than martensitic stainless steel. Both thickness and microhardness measurements indicated that effect of the nitriding treatment was more sensitive in austenitic stainless steel than martensitic stainless steel with nitriding time. Fatigue strength was most increased with SACM 645 steel among three steels.