• Composites Research
• /
• v.34 no.6
• /
• pp.387-393
• /
• 2021

This paper investigated the electrical properties of multiwall carbon nanotube reinforced polydimethylsiloxane (CNT-PDMS) strain sensors with copper electrodes on the wet-etched surface. MWCNT-PDMS strain sensors were fabricated according to the wt% of MWCNT. Surfaces on the electrode area were wet-etched with various etching duration and silver epoxy adhesives were spread on the wet-etched surface. Finally, we attached the copper electrodes to the MWCNT-PMDS strain sensors. We checked the electric conductivities by the two-probe method and sensing characteristics under the cyclic loading. We observed the electric conductivity of MWCNT-PDMS strain sensors increased sharply and the scattering of the measured data decreased when the surface of the electrode area was wet-etched. Initial resistances of MWCNT-PDMS strain sensors were inversely proportion to wt% of MWCNT and the etching duration. However, the resistance changing rates under 30% strain increased as wt% of MWCNT and the etching duration increased. Decreasing rate of the electric resistance change after 100 repetitions was smaller when wt% of MWCNT was larger and the etching duration was short. This was due to the low initial resistance of the MWCNT-PMDS strain sensors by the wet-etching.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.605-609
• /
• 2010

In modern surveillance equipment, infrared (IR) sensors are essential for detection and observation. The IR sensor is connected to a miniature cryogenic cooler to maintain the temperature at very low levels, i.e., temperatures as low as 77 K. However, the quality of the image captured by the sensor is degraded by the transmission of vibration disturbances from the cooler. Therefore, to maintain high image quality, the compressor vibration and the force transmitted to the sensor have to be mitigated. For the compressor vibration isolating system, a tuned dynamic vibration absorber, combined with a passive isolator, is proposed. A cryogenic compressor bracket and springs are designed to allow the absorber mass to mitigate the vibration jitter in the axial direction. The system design is analyzed and evaluated in terms of the dynamic suppression of the harmonic force at the operating frequency of the cooler.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.6
• /
• pp.675-680
• /
• 2012

Wind energy is currently the fastest growing source of renewable energy used for electrical generation around the world. Wind farms are adding a significant amount of electrical generation capacity. The increase in the number of wind farms has led to the need for more effective operation and maintenance. CMS(Condition Monitoring System) can be used to aid plant operator in achieving these goals. Its aim is to provide operators with information regarding th e health of their machine, which in turn, can help them improve operation efficiency. In this work, wind turbine fault diagnostic algorithm which can diagnose the mass unbalance and aerodynamic asymmetry of the blades is proposed. Proposed diagnostic algorithm utilizes both FFT(Fast Feurier Transform) of the signal from accelerometers installed inside of nacelle and simple diagnostic logic. Furthermore, to verify the applicability of the proposed system, 3W small sized wind turbine system is tested and physical experiments are carried out.

• Korean Journal of Remote Sensing
• /
• v.20 no.6
• /
• pp.419-425
• /
• 2004

This study has proposed a data fusion method based on the Dempster-Shafer evidence theory The Dempster-Shafer fusion uses mass functions obtained under the assumption of class-independent Gaussian assumption. In the Dempster-Shafer approach, uncertainty is represented by 'belief interval' equal to the difference between the values of 'belief' function and 'plausibility' function which measure imprecision and uncertainty By utilizing the Dempster-Shafer scheme to fuse the data from multiple sensors, the results of classification can be improved. It can make the users consider the regions with mixed classes in a training process. In most practices, it is hard to find the regions with a pure class. In this study, the proposed method has applied to the KOMPSAT-EOC panchromatic image and LANDSAT ETM+ NDVI data acquired over Yongin/Nuengpyung. area of Kyunggi-do. The results show that it has potential of effective data fusion for multiple sensor imagery.

• Journal of the KSME
• /
• v.29 no.2
• /
• pp.175-183
• /
• 1989

오늘날 널리 연구되고 있고 공학자들에게 많은 관심을 끌고있는 압전 세라믹(ceramic)을 이용 하여 자연계에서 일어나는 각종 진동현상을 측정하고 해석하기 위한 센서(sensor)의 설계, 제작은 이미 선진국에서도 보편화된지 오래이다. 특히 압전형 가속도계(piezo type accelerometer)는 진동의 절대 측정에 가장 유용한 센서로 널리 알려져 있다. (1) 아주 넓은 사용 주파수 범위 (2) 넓은 동적범위(dynamic range)에 걸친 뛰어난 선형성(linearity) (3) 측정된 가속도 신호를 전기적으로 적분하여 속도와 변위에 대한 자료 제공 용이 (4) 높은 정확성 (5) 자발 전(self-generating)이므로 외부 전원 공급이 불필요 (6) 수명과 뛰어난 내구성 (7) 작은 크기와 가벼운 무게 등이다. 현재 기계 구조물 진동 측정에 이용되고 있는 스트레인 게이지 형(strain gage-type)의 가속도계는 감도가 좋고 저주파 진동 측정에는 편리한 반면 충격이나 높은 주파수 전동 측정에는 적합하지 않으며 내부 구조가 다소 복잡하다(2). 반면에 압전형 가 속도계는 압전 소자와 관성 질량의 조합 설계로서 저주파 진동 측정에 적합한 고감도의 가속도 계와, 감도는 떨어지나 아주 높은 주파수 범위의 진동까지 측정이 가능한 가속도계를 손쉽게 설계, 제작할 수 있다. 본 글에서는 선진국에 비해 낙후된 국내의 센서 설계, 제작 기술을 고 양시키고자 최근 한국과학기술원에서 시도된 압전형 가속도계의 개발 연구 사례를 중심으로 설계 및 제작시 고려 사항과 보정 문제를 소개하고자 한다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.4
• /
• pp.87-94
• /
• 1998

Increasing flexibility and lightness of recently built high-rise buildings make the structures susceptible to loads such as earthquakes and winds. Therefore, higher performance vibration control systems to reduce the vibration levels are demanded more than any time in the past. One of the typical active vibration control systems is the active mass driver (AMD). In this paper, an active vibration control system consisting of small shaking table, building model, sensors, signal processing board and AMD is constructed. The dynamic characteristics of these individual systems are investigated through the experimental study. The performance of the active vibration control system is verified through the El Centro earthquake(1940,NS) on the building model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.2
• /
• pp.63-70
• /
• 2003

In this paper, an MFC (Mass Flow Controller) which is widely used in many semiconductor manufacturing processes for controlling the mass flow rate of a gas is designed and implemented using the PIC 16F876 of Microchip, Inc. The MFC implemented in this thesis has the form of hybrid-type, i.e., the mixed-type of the analog-type MFC, which has many problems such as low accurary, and digital-type MFC, which use an expensive DSP (Digital Signal Processor) and an ADC (Analog to Digital Convertor) with high precision. The MFC is consists of the sensor unit, the control unit and the actuator unit, and it has used the automatic calibration algorithm and the reference table method for the improvement of the performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.331-331
• /
• 2010

본 연구에서는 차량 하중에 의해 압전체가 변형되어 전기에너지를 발생시키는 도로용 압전에너지 하베스터를 개발하기위한 설계 및 실험을 진행하였다. 최대의 전기에너지가 발생되도록 압전사각 시트를 닥터브레이드로 제작하여, 이를 강판에 부착하고 고유주파수를 낮추기 위해 끝단에 질량을 달아 캔틸레버형태의 구조로 제작하였으며 끝단 질량의 변화와 가진주파수에 따른 발전특성을 비교하였다. 이로써 도로용 센서 및 방향지시등의 전원으로 사용하기 위한 도로매설용 압전 에너지 하베스터의 타당성을 확인하였다.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.2
• /
• pp.155-161
• /
• 2016

This paper proposes a novel fabrication method for a capacitive type micro-accelerometer with uniform nano-gap using photo-assisted electro-chemical etching. The sensitivity of the accelerometer should be improved while the electrodes between the inertial mass and the sensing comb should be narrowed. In this paper the nano-gap trench structure is fabricated using the photo-assisted electrochemical etching method. The sensor was designed and analysed using ANSYS simulator. The characteristics of the etching were observed according to the dc bias, the light intensity, the composition of the solution, the temperature of the solution, and the pattern pitch variation. The optimum etching conditions were dc bias of 2V, Blue LED of 20mA, 49wt% HF:DMF:D.I.Water=1:20:10, the pattern pitch of $20{\mu}m$. Uniform trench structure with width of 344nm and depth of $11.627{\mu}m$ are formed using the optimum condition.

• Composites Research
• /
• v.18 no.6
• /
• pp.26-33
• /
• 2005

The mechanical properties of composite materials may severely degrade in the presence of damage. Especially, the high-velocity impact such as bird strike, a hailstorm, and a small piece of tire or stone during high taxing, can cause considerable damage to the structures and sub-system in spite of a very small mass. However, it is not easy to detect the damage in composite plates using a single technique or any conventional methods. In this paper, the PVDF(polyvinylidene fluoride) film sensors were used for monitoring high-velocity impact damage initiation and propagation in composite laminates. The WT(wavelet transform) and STFT(short time Fourier transform) are used to decompose the sensor signals. A ultrasonic C-scan and a digital microscope are also used to examine the extent of the damage in each case. This research shows how various sensing techniques, PVDF sensor in particular, can be used to characterize high-velocity impact damage in advanced composite.