• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.596-602
• /
• 2013

In general, existed vibration energy harvester is optimum in electronic energy gleaned from vibration energy with fixed single frequency, because it is using resonance. But it is limit in electronic energy gleaned from ocean wave energy with variant frequency. This paper studied for width band vibration energy harvester that obtains electronic energy from ocean wave with infinite vibration energy in order to solve it. It is composed of buoy to occur resonance in the center frequency of ocean wave energy and the vibration system to occur resonance in the same frequency. As a result, existed vibration energy harvester using resonance maximized electronic energy conversion efficiency in single frequency, while proposed width band vibration energy harvester has merit that maximized electronic energy conversion efficiency in ocean wave with variant frequency.

• Tunnel and Underground Space
• /
• v.20 no.2
• /
• pp.112-118
• /
• 2010

Before blasts that can have direct impacts on human bodies or structures, it is necessary to assess impacts of ground vibration. Therefore, frequency has been recognized as an important factor in order to assess impact on ground vibration and damages. There have been many studies on impacts of frequency. But, there have been no studies on relations between vibration and frequency according to delay time difference. In this study, we examined the relations between delay time difference and frequency according to each frequency with which reinforcement and destructive intervention repeat through delay time difference obtained using superposition modeling of single hole blasting waveform based on the theory of time difference developed by Langefors.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.991-997
• /
• 2000

The objective of this study is to examine the onset condition and the frequency characteristics of the low-frequency combustion oscillation in a surface burner. For this purpose, extensive parametric studies have been performed experimentally and the effects of size of each section, the equivalence ratio, and the entrance velocity on oscillatory behavior explored. The experimental results were discussed in comparison with the other combustors associated tilth the low-frequency combustion oscillation. The combustion mode is driven at high combustion rate by the lift of unstable flame near the lower limit of the combustible equivalence ratio. The oscillation frequency is dependent not on the burner geometry but on the equivalence ratio and the combustion load. Low-frequency combustion mode was formed to be divided into two different modes, named C1 and C2 respectively. Two modes occurred individually, simultaneously or transitionally according to the equivalence ratio and combustion load. The characteristics of low-frequency oscillation is different from each other depending on the type of combustors. The surface burner has also its own characteristics of low -frequency oscillation.

• Journal of the Korean Institute of Gas
• /
• v.13 no.1
• /
• pp.9-13
• /
• 2009

A cause of noise and vibration which come from a Combustion of gas heater are a combustion roar and Combustion oscillation. A character of a combustion roar is that sound pressure is distribute with broad band frequency. otherwise, The presence of combustion oscillation caused by positive Feed Back in Combustion Chamber break out a noise and vibration. Accordingly, The method that be solved a noise and vibration is to make each natural frequency different frequency. first, in order to solve problem, we control ratio of fuel and air. that is, Keep away resonance. second, in order to changing natural frequency of Combustion Chamber, We changed the shape of Economizer.

• Journal of Korean Association for Spatial Structures
• /
• v.9 no.1
• /
• pp.79-85
• /
• 2009

As a recent spatial structure have become long-spaned and light, stiffness of out-plane is reduced significantly. Due to this, it is necessary to calculate natural frequency correctly to check if structure is flexible or vortex-induced vibration is occurred. However, formula of frequency in domestic and foreign spatial structure has not been performed deeply. In this study, approximated formula obtained by eigenvalue analysis of seven domestic spatial structure is compared with two suggestions based on Japanese standard and formula by measurement of 28 spatial structure in Japan. Natural frequency of roof has a tendency to be reduced as the span of structure increases. Natural frequency of domestic structure is generally less than that of analysis and measurement of spatial structure in Japan. Therefore, it is confirm that roof of domestic spatial structure is relatively rather flexible than that of Japan.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.963-968
• /
• 2004

Free vibration analysis of helical spring with crack was studied. Natural frequency changes due to the crack was analyzed with respect to crack locations. The effect of crack on natural frequency was decreased as crack location is further from the fixed end of a spring. The frequency change was larger in rectangular-shaped spring than that in circular-shaped spring. It was found that experiment may not be appropriate to determine the presence of crack because no significant natural frequency change can be shown by experiment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.827-829
• /
• 2014

This paper presents a design methodology for improving dynamic stiffness of an inspection robot frame to prevent resonance. Finite element models of robot frame are developed for natural frequency analysis. Natural frequency analysis of robot frame is conducted to compare with sub-span oscillation which is excitation frequency. Reinforcement beams are applied to the sensitive parts of the robot frame to improve dynamic stiffness using case study. To reduce mass of the robot frame, thickness optimization of the robot frame is carried out by utilizing response surface method. The result of optimization show that dynamic stiffness of robot frame is increased. As a result, natural frequency of an optimal model is not included in range of frequencies of the sub-span oscillation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.227-236
• /
• 2002

We have performed two kinds of experimental modal analyses fur a radial tire for passenger car under free-suspension. One is the modal analysis to obtain three-dimensional modes of tire using accelerometers and the other is the one to identify cavity resonance frequency using a pressure sensor. From the first analysis, we have obtained the three-dimensional natural modes, which makes it possible to grasp the features of the modes and to classify the vibrational modes into symmetric, non-symmetric, and antisymmetric modes in a simple way by using the experimental results. From the first and the second experimental analyses we have identified the cavity resonance frequency and its three-dimensional mode shape.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.13 no.3
• /
• pp.14-23
• /
• 1993

A method to measure the resonance frequency of the ultrasonic transducer which is adhered to the specimen by the ultrasonic visualization is tried. The result shows that the resonance frequency of the transducer adhered to the specimen is lower than the nominal resonance frequency of the transducer in itself and the greater the degree of deviation. It is verified that its cause is the resonance of Al-plate for protecting the transducer by the theoretical analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.434-438
• /
• 2006

The purpose of this paper is that investigates the Natural Frequency behavior characteristic of Wind Turbine Jacket Type Tower model, and calculated that the stress values of Thrust Load, Wave Load, Wind Load, Current Loda, Gravity Load, etc., environment evaluation analysis during static Operating Wind Turbine Jacket Type Tower model, carried out of Natural Frequency analysis of total load case to stress matrix, Frequency calculated that calculated Add Natural Frequency to stiffness matrix for determinant to stress results. The finite element analysis is performed with commercial F.E.M program (ANSYS) on the basis of the natural frequency and mode shape.