• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.4
• /
• pp.457-463
• /
• 2012

The basilar membrane (BM), one of organs of cochlea, has the specific positions of the maximum amplitude at each of related frequencies. This phenomenon is due to the geometry of BM. In this study, as the part of the research for the development of fully implantable artificial cochlea which is based on polymer membrane, parametric studies are performed to suggest the desirable artificial basilar membrane model which can detect wider range of frequency separation. The vibro-acoustic characteristics of the artificial basilar membrane are predicted through finite element analysis using commercial software Abaqus. Simulation results are verified by comparing with experimental results. Various geometric shapes of the BM and residual stress effects on the BM are investigated through the parametric study to enable a wider detectable frequency separation range.

• Nuclear Engineering and Technology
• /
• v.20 no.2
• /
• pp.88-104
• /
• 1988

The FUel Rod Analysis(FURA) code is developed using two-dimensional finite element methods for axisymmetric and plane stress analysis of fuel rod. It predicts the thermal and mechanical behavior of fuel rod during normal and load follow operations. To evaluate the exact temperature distribution and the inner gas pressure, the radial deformation of pellet and clad, the fission gas release are considered over the full-length of fuel rod. The thermal element equation is derived using Galerkin's techniques. The displacement element equation is derived using the principle of virtual works. The mechanical analysis can accommodate various components of strain: elastic, plastic, creep and thermal strain as well as strain due to swelling, relocation and densification. The 4-node quadratic isoparametric elements are adopted, and the geometric model is confined to a half-pellet-height region with the assumption that pellet-pellet interaction is symmetrical. The pellet cracking and crack healing, pellet-cladding interaction are modelled. The Newton-Raphson iteration with an implicit algorithm is applied to perform the analysis of non-linear material behavior accurately and stably. The pellet and cladding model has been compared with both analytical solutions and experimental results. The observed and predicted results are in good agreement. The general behavior of fuel rod is calculated by axisymmetric system and the cladding behavior against radial crack is used by plane stress system. The sensitivity of strain aging of PWR fuel cladding tube due to load following is evaluated in terms of linear power, load cycle frequency and amplitude.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.436-444
• /
• 2013

This article presents the dynamic response of nano-scale plates using the nonlocal continuum theory and higher-order shear deformation theory. The nonlocal elasticity of Eringen has ability to capture the small scale effects and the higher-order shear deformation theory has ability to capture the quadratic variation of shear strain and consequently shear stress through the plate thickness. The solutions of transient dynamic analysis of nano-scale plate are presented using these theories to illustrate the effect of nonlocal theory on dynamic response of the nano-scale plates. The relations between nonlocal and local theories are discussed by numerical results. Also, the effects of nonlocal parameters, aspect ratio, side-to-thickness ratio, size of nano-scale plate and time step on dynamic response are investigated and discussed. The amplitude and cycle increase when nonlocal parameter increase. In order to validate the present solutions, the reference solutions are used and discussed. The theoretical development as well as numerical solutions presented herein should serve as reference for nonlocal theories as applied to the transient dynamic analysis of nano-scale structures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.345-353
• /
• 2007

We have obtained a topographical image nondestructively for a Cu thin film in liquid using a near-field scanning microwave microscope (NSMM), its operating frequency was 3.5 to 5.5 GHz. We have kept a distance of 10 nm between tip and sample using a quartz tuning fork shear force feedback system. As an end of tip was attached to one prong of the quartz tuning fork has a length of 2 mm, the only tip of tuning fork was immersed in water tank. A loss cause by evaporation in water tank is regulated with actuator was connected to a supplementary tank. Moreover, using a revise program of LabView, we could increase the accuracy of a measurement in liquid.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.253-253
• /
• 2019

유사의 이동은 하천, 해안 지역과 같은 수계에서 하상의 변동, 침식과 퇴적을 일으켜 지형적인 변화를 초래한다. 유사의 이동은 유사의 특성과 유체의 유수동역학적 특성에 의해 결정되며 유체특성 간의 복잡한 상호 작용에 의해 변화한다. 유사가 가지는 점착성은 유사의 특성에 큰 영향을 끼친다. 입자의 크기가 매우 작은 점착성 유사는 그 표면이 가지는 전자기적 점착력에 의해 주위의 1차 입자나 다른 작은 알갱이들이 서로 뭉치는 응집과 충돌에 의해 크기가 작아지는 파괴의 과정을 겪는다. 이 과정을 응집현상이라고 하며 응집현상을 통해 점착성 유사의 크기와 밀도, 침강속도는 계속해서 변화한다. 따라서 점착성 유사의 응집거동 고려한 유사 이동 연구는 필수적이다. 과거 연구의 많은 사례에서 유사의 크기와 농도는 비례 관계를 가지는 것이 일반적이라 알려져 있다. 그러나 실제 현장에서 측정한 결과 유사의 크기와 농도가 반비례 관계를 가지는 특이점이 발견되었다. 실측 연구에서 발견된 응집거동에 따른 유사의 특성의 특이한 변화를 설명하기 위해 1차원 연직 수치 모형(1DV)을 이용하여 수치 실험을 수행하였다. 모의 수행 시, 흐름 조건을 크기와 방향이 일정한 순방향흐름(Current)에 특정 주기와 진폭을 가지는 진동 흐름(Oscillatory Flow)을 추가하여 진행하였다. 플럭의 성장과 그에 따른 입자의 크기는 많은 현상에 영향을 받는다. 그 중 응집현상의 응집 과정과 파괴 과정 중 어떤 현상이 더 우세한지 그 경쟁관계를 파악하여 플럭의 크기의 증감을 예측할 수 있게 농도(?)와 난류소산매개변수(?)를 이용하여 $c/G^{0.5}$로 매개화하였다. 실험 결과, 순방향 흐름을 제외하고 스토크스파 흐름 조건을 이용하여 진행된 모의에서는 플럭의 크기와 농도가 반비례하는 현상을 관찰할 수 없었으며 $c/G^{0.5}$ 의 변화 역시 흐름의 속도와 농도가 더 큰 지점에서 큰 값을 가지는 일반적인 결과를 나타내었다. 그러나 같은 조건에서 순방향흐름을 추가하여 모의한 결과에서는 플럭의 크기와 농도가 반비례하는 현상을 나타냈다. 연직 방향 $c/G^{0.5}$의 변화를 나타낸 그래프에서 응집과 파괴의 우세에 따라 $c/G^{0.5}$ 가 역전되는 현상을 확인하였다. 즉, 플럭의 크기는 난류의 구조와 그 영향에 의해 농도와 비례관계를 갖지 않을 수도 있다고 판단된다. 또한 본 연구에서 정상류 흐름 조건의 유무에 따라 플럭의 크기와 농도가 비례하거나 반비례하는 상반된 결과를 보였다. 정상류 흐름 조건이 난류의 강도에 큰 역할을 하며 이에 따라 비선형 관계에 영향을 끼친다는 것을 발견하였다. 그러나 흐름의 영향에 대한 더 자세한 분석은 본 연구에서 진행되지 않았으며 향후 연구 시에 분명히 고려되어야 할 사항이다.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.12
• /
• pp.19-28
• /
• 2022

Cavities behind concrete walls can adversely affect the stability of structures. Thus study aims to detect cavities behind concrete structures using a microphone in a laboratory model test. A small-scale concrete wall is constructed in a chamber, which is composed of a reinforced concrete plate and dry soil. A plastic bowl is then placed between the plate and soil to simulate a cavity behind the concrete structure. Leaky surface acoustic waves are generated by impacting the concrete plate using a hammer and are measured using a microphone. The measured signals are analyzed using natural frequencies, and cavity-free sections are evaluated. The test results show that the first natural frequency decreases at the cavity section due to the flexural vibration behavior of the plate. In addition, the amplitude corresponding to the first natural frequency decreases as the measurement location becomes farther from the cavity center and significantly decreases at the measurement locations near the rebars. This study demonstrates that a microphone may be useful to detect cavities behind concrete walls.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.887-899
• /
• 2006

The aim of this study is to investigate a correlation between fundamental data on aerodynamic characteristics of bridge girder cross-sections, such as aerodynamic force coefficients and flutter derivatives, and their aerodynamic behaviour. The section model tests were carried out in three stages. In the first stage, seven deck configurations were studied, namely; Six 2-edge girders and one box girder. In this stage, changes in aerodynamic force coefficients due to geometrical shape of girders, incidence angle of flow, wind directions and turbulence intensities were studied by static section model tests. In the second stage, the dynamic section model tests were carried out to investigate the relativity of static coefficients to dynamic responses. And finally, the two-dimensional (lift-torsion) aerodynamic derivatives of three bridge deck configurations were investigated by dynamic section model tests. The aerodynamic derivatives can be best described as a representation of the aerodynamic damping and the aerodynamic stiffness provided by the wind for a given deck geometry. The method employed here to extract these unsteady aerodynamic properties is known as the initial displacement technique. It involves the measurement of the decay in amplitude with time of an initial displacement of the deck in heave and torsion, for various wind speeds, in smooth flow. It is suggested that the proposed aerodynamic force coefficients and flutter derivatives of bridge girder sections will be potentially useful for the aeroelastic analysis and buffeting analysis.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.34 no.1
• /
• pp.74-84
• /
• 1998

A doubly resonant ultrasonic transducer has been designed as an attempt to increase the bandwidth of underwater transducers. The dual resonance conditions were accomplished by attaching a single acoustic matching layer on the front face of a Tonpilz transducer consisted of an aluminum head, a piezoelectric ring, a brass tail and a prestress bolt. A modified Mason's model was used for the performance analysis and the design of transducers, and the constructed transducers were tested experimentally and numerically by changing the impedances and thicknesses of the head, tail and matching layers in the water tank. Two distinct resonance peaks in the transmitting voltage response(TVR) of a developed transducer were observed at 34.3 and 40.4 kHz, respectively, with the difference frequency of 6.1kHz and the center frequency of 37.2kHz. The values of TVR at these frequencies were 136.5 dB re $1\;\muPa/V$ at 34.3 kHz and 136.8 dB re $1\;\muPa/V$ at 40.4 kHz, respectively. Reasonable agreement between the experimental results and the numerical results was achieved. From this result, it is expected that the generation of the distinct resonances at any two desired frequencies can be achieved through the proper choice of the matching layer to provide the impedance transformation between the transducer and the medium.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.249-254
• /
• 2022

With the rapid advance of the semiconductor and Information and communication technologies, remote environment monitoring technology, which can detect and analyze surrounding environmental conditions with various types of sensors and wireless communication technologies, is also drawing attention. However, since the conventional remote environmental monitoring systems require external power supplies, it causes time and space limitations on comfortable usage. In this study, we proposed the concept of the self-powered remote environmental monitoring system by supplying the power with the levitation-electromagnetic generator (L-EMG), which is rationally designed to effectively harvest biomechanical energy in consideration of the mechanical characteristics of biomechanical energy. In this regard, the proposed L-EMG is designed to effectively respond to the external vibration with the movable center magnet considering the mechanical characteristics of the biomechanical energy, such as relatively low-frequency and high amplitude of vibration. Hence the L-EMG based on the fragile force equilibrium can generate high-quality electrical energy to supply power. Additionally, the environmental detective sensor and wireless transmission module are composed of the micro control unit (MCU) to minimize the required power for electronic device operation by applying the sleep mode, resulting in the extension of operation time. Finally, in order to maximize user convenience, a mobile phone application was built to enable easy monitoring of the surrounding environment. Thus, the proposed concept not only verifies the possibility of establishing the self-powered remote environmental monitoring system using biomechanical energy but further suggests a design guideline.

• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.234-246
• /
• 1998

The objective of this study is to investigate the correlation between steady shear flow (nonlinear behavior) and dynamic viscoelastic (linear behavior) properties for concentrated polymer solutions. Using both an Advanced Rheometic Expansion System(ARES) and a Rheometics Fluids Spectrometer (RFS II), the steady shear flow viscosity and the dynamic viscoelastic properties of concentrated poly(ethylene oxide)(PEO), polyisobutylene(PIB), and polyacrylamide(PAAm) solutions have been measured over a wide range of shear rates and angular frequencies. The validity of some previously proposed relationships was compared with experimentally measured data. In addition, the effect of solution concentration on the applicability of the Cox-Merz rule was examined by comparing the steady flow viscosity and the magnitude of the complex viscosity Finally, the applicability of the Cox-Merz rule was theoretically discussed by introducing a nonlinear strain measure. Main results obtained from this study can be summarized as follows : (1) Among the previously proposed relationships dealt with in this study, the Cox-Merz rule implying the equivalence between the steady flow viscosity and the magnitude of the complex viscosity has the best validity. (2) For polymer solutions with relatively lower concentration, the steady flow viscosity is higher than the complex viscosity. However, such a relation between the two viscosities is reversed for highly concentrated polymer solutions. (3) A nonlinear strain measure is decreased with increasing stran magnitude, after reaching the maximum value in small strain range. This behavior is different from the theoretical prediction demonstrating the shape of a damped oscillatory function. (4) The applicability of the Cox-Merz rule is influenced by the $\beta$ value, which indicates the slope of a nonlinear stain measure (namely, the degree of nonlinearity) at large shear deformations. The Cox-Merz rule shows better applicability as the $\beta$ value becomes smaller.