• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.1
• /
• pp.35-44
• /
• 1990

Most of the medium-size ships are powered by large-bore, long-stroke, slow-speed and two-stroke diesel engines in order to improve the fuel efficiency. Such a propulsion plant develops low-frequency excitation forces/moments of significant magnitude. A RO/RO car/truck carrier is also one of the cases. In this paper, the rational methods for analysis of vertical and coupled horizontal-torsional vibrations are presented. Taking account of unusual characteristics of the hull form and structural systems, the emphasis is put on modelling methods based on beam analogy, calculation of system parameters such as added mass and its center, polar added-mass moment of inertia, shear coefficient of hull sections and coupling degree in antisymmetric modes, and modal analysis of forced vibrations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.1
• /
• pp.94-101
• /
• 2019

Most of the existing rail structures have undergone a lot of aging since a considerable period of time has passed from completion. In particular, among existing railway bridges, many of the plate girder bridges are older bridges that have lived 40 to 60 years or more. Since the treadmill is directly connected to the girder without the ballast, the running load of the vehicle is directly transmitted to the bridge. Therefore, the shock and noise applied to the bridge are larger than those of the ballast bridge, and the dynamic shock and vibration are also relatively large. Therefore, it is very urgent to develop appropriate maintenance, repair and reinforcement technology for existing steel plate bridge. In this study, the authors introduced the characteristics of embedded rail (ERS) developed for improving the performance of the existing plate girder bridge and the techniques solving the vibration and noise problems. In order to evaluate the vibration and noise reduction performance of ERS, a non-ballast plate girder bridge with 5m length of sleepers installed and a plate girder bridge with ERS were fabricated. And, then, the vibration response generated under the same excitation condition was measured and analyzed. Also, the radiated noise analysis was performed using the vibration response data obtained from the experiment as the input data of the acoustic analysis model. As a result of experiments and analyses, it was confirmed that the plate girder bridge's vibration using ERS was reduced by 15.0~18.8dB and the average noise was reduced by 7.7dB(A) more than the non-ballast bridge.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.93-97
• /
• 2009

An advantage of a magnetostrictive strip transducer for a long-range guided wave inspection is that the wave patterns are relatively clear and simple when compared to a conventional piezoelectric ultrasonic transducer. Therefore, if we can characterize the evolution of defect signals, it could be a promising tool for a structural health monitoring of pipes for a long period of time as well as an identification of flaws. However, when evaluating a signal during a realistic field examination, it should be careful because of some spurious signals or false indications, such as signals due to a directionality, multiple reflections, mode conversion, geometrical reflections etc. Mode converted signals from a realistic piping mockup were acquired and analysed. We found mode conversions between a torsional guided wave T(0,1) mode and a flexural F(1,3) or longitudinal L(0,2) mode generated by a magnetostrictive strip transducer. Based on the experimental observations, an interpretation of the source of the mode conversion is discussed in a viewpoint of electromagnetic properties and structure of the strip transducer.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.10a
• /
• pp.117-124
• /
• 1993

본 연구에서는 공기스프링을 능동요소로 사용한 방진대를 1자유도 및 2자유도로 모델링하여 이론해석을 수행하였고, 이에 따른 컴퓨터시뮬레이션과 실험을 통하여 이론의 타당성을 검증하였다. 다음으로 공기스프링 방진대의 방진성능 향상을 위하여 비례제어밸브, 컴퓨터, 측정센서 등을 이용하여 공기 스프링내의 공기압력을 능동적으로 조절할 수 있는 제어계를 구성한 후, 최적제어 및 퍼지제어 알고리즘을 적용하여 상태귀환 제어를 실시하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.4
• /
• pp.343-350
• /
• 2011

Recently, as the catastrophic disasters due to earthquake happen frequently all over the world, it draws lots of attention to seismic capacity evaluation and/or structural integrity assessment of deteriorated civil infra-structures. However, there have been few studies on the existing dam flood gates, expecially in Korea. In this study, a proper vibration testing method applicable to a dam flood gate has been suggested, since the dynamic characteristics of a darn flood gate can be fundamental data for seismic capacity evaluation or structural integrity assessment. The frequency domain decomposition technique has been incorporated for modal parameter identification. Two kinds of vibration tests using an impact hammer and ambient vibration sources were carried out on two types of dam floodgates with different shapes. Through the field tests, the effectiveness of the ambient vibration tests were verified.

• Journal of the Korean Society for Railway
• /
• v.16 no.1
• /
• pp.7-13
• /
• 2013

A scaled version of a roller rig is developed to demonstrate the dynamic characteristics of a railway vehicle for academic purposes. This rig is designed based on Jaschinski's similarity law. It is scaled to 1/10 of actual size and allows 9-DOF motion to examine the up and down vibration of a train set. The test rig consists of three sub-hardware components: (i) a driving roller mechanism with a three-phase AC motor and an inverter, (ii) a bogie structure with first and second suspensions, and (iii) the vehicle body. The motor of the rig is capable of 3,600rpm, allowing the test to simulate a vehicle up to a maximum speed of 400Km/hr. Because bearings and joints are properly connected to the sub-structures, various motion analyses, such as a lateral, pitching, and yawing motion, are allowed. The slip motion between the rail and the wheel set is also monitored by several sensors mounted in the rig. After the construction of the hardware, an experiment is conducted to obtain the natural frequencies of the dynamic behavior of the specimen. First, the test rig is run and data are collected from six sets of accelerometers. Then, a numerical analysis of the model based on the ADAMS program is derived. Finally, the measurement data of the first three fundamental frequencies are compared to the analytical result and the validation of the test rig is conducted. The results show that the developed roller rig provides good accuracy in simulating the dynamic behavior of the vehicle motion. Although the roller rig designed in this paper is intended for academia, it can easily be implemented as part of a dynamic experiment of a bogie and a vehicle body for a high-speed train as part of the research efforts in this area.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.4
• /
• pp.62-69
• /
• 2010

In this study, the serviceability performance of Waffle Shaped(WAS) and Double-Tee(DT) precast concrete slabs were evaluated and compared based on the vertical acceleration magnitude induced by walking and heel drop loads. Tests were conducted for practical building structures of which floor systems used WAS and DT slabs. Natural frequencies of the slabs were similar to those obtained by using analytical models. The measured acceleration level was evaluated by vertical floor acceleration criteria presented by ISO-2631, AIJ(1991, Japan) and a previous study regarding floor vibration limit. Test results showed that both WAS and DT slabs satisfied all the criteria and Peak acceleration level of WA slabs was lower than that of DT slabs.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.4 s.77
• /
• pp.407-417
• /
• 2005

An experimental and analytical study was performed to apply the friction pendulum system (FPS) to the main control room of a nuclear power plant. A friction pendulum bearing was fabricated, and the dynamic response of the bearing was evaluated. A partial model of a main control room attached to the FPS was tested on the shake table. The model consisted of a cabinet, a $3m\times3m$ access floor, and four friction pendulum bearings. The artificial time history based on the floor response spectrum of the main control room was used as the earthquake input signal in the test. Comparisons between the analytical study and the experimental study were conducted to verify the results and to extend the experimental study to the range of parameters that could not be experimentally studied.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1990.10a
• /
• pp.9-14
• /
• 1990

맥동 연소기는 기존의 연속 연소식 연소기에 비하여 높은 열효율, 소형화, 연소과정의 개선, 시동후 점화플러그 및 송풍팬의 불필요, 자력 배기와 장시 간 안전 운전등의 장점들로 인하여 최근 연구대상으로서 주목을 받고 있다. 맥동연소 현상은 1800년경부터 알려졌음에도 불구하고 기본적인 연소메카니 즘 및 기본동작 원리에 대한 미비점 및 높은 소음 등으로 인하여 종래의 연 구는 거의 실험을 통하여 이루어 졌으며 이러한 것들이 현재까지도 맥동 연 소기의 발전에 걸림돌이 되고 있다. 맥동 연소기가 산업용 및 가정용 열기기 로서 사용되기 위하여 진동과 소음의 감소에 대한 엄격한 요구를 만족하지 않으면 안된다. 따라서, 그에 대한 효과적인 방지 설계를 하기 위하여 진동 원과 소음원이 어느 부위에서 전달되어 오는지를 파악하는 것이 중요하다.. 본 연구에서는 맥동연소기의 소음원을 규명하기 위하여 종래에 사용되어 온 주파수 응답함수법과 소음원간에 강한 상관관계가 존재하는 경우에 사용되 는 기여도함수법을 이용하여 다차원 스펙트럼해석법에 의하여 입출력간의 기여관계를 규명하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.35-39
• /
• 1993

항공기의 플러터 현상을 예방키 위한 개발시의 주요 공학적 임무로는 플러 터 해석, 풍동 플러터 시험, 실기체에 대한 지상진동시험 및 비행 플러터 시 험이 있다. 이들 업무는 군용 항공기의 경우에는 군사 규격서, 민간 항공기 의 경우는 FAR 규정 등에 항공기 개발 및 개조시에는 필히 수행토록 명시 되어 있으며, 특히 개발항공기의 인증을 받기 위해서는 초도 비행전까지 필 수적으로 완료되어야 하는 업무이다. 이중 항공기 지상진동시험은 개발항공 기의 초도 비행전에 실기체를 대상으로 하는 구조 동특성 규명시험으로써 플러터 해석 모델의 정확도를 입증하고 그 해석모델을 수정하거나 개선시키 는데 필요한 구조의 동특성 변수들을 실험적으로 규명하는 시험이다. 이 시 험은 개발된 항공기의 초도비행허가를 획득하고 비행속도제한을 설정키 위 해서 초도비행 직전에 초도 개발 비행기를 대상으로 필수적으로 수행되어야 하는 필수적 시험이다. 이에 따라 개발된 항공기의 전기체 지상진동시험을 수행하였고, 시험데이터의 모달해석을 하였다. 이 시험을 수행하기 위해 3개 의 가진기를 사용하였고, 모두 159개의 지점에서 주파수응답 함수를 얻었다. 최대 48 채널의 데이터 획득시스템을 사용하였으므로, 네번에 걸쳐 측정위치 를 옮겨 전체데이타를 획득하였다. 지상진동 시험의 최종해석 결과는 유한요 소 모델의 유효성을 검토하는데 사용되었고, 시험 데이타를 이용한 가진응답 해석(Forced Response Analysis)을 통하여 비행플러터 시험시에 사용되는 플러터 가진기의 위치선정 및 가진력의 크기를 결정하는데 이용하였다.ncy)가 저주 파수대로 천이(Lower Shift)하는 현상이 나타났으며, 일정한 작업량이라도 작업중량을 줄이고 작업 빈도를 높여서 작업할 경우에 이러한 현상이 더욱 두드러졌다. 작업시간의 경과에 따른 MVIS의 감소 현상은 작업빈도가 높고 비대칭형 작업일 때 가장 크게 나타났다. 총손실을 줄이고, 상대적 비용절감효과를 갖게할 수 있다고 하였다. 따라서 본 연구에서는 성인 여성기성복의 치수적합성을 높이기위하여 출산 후 중년에 접어 들면서 체형이 변화되는 것을 고려하여 연령을 분류하고(18세-34세, 30세-51세), 각 연령 집단에 따른 체형을 각각 3가지로 분류하였다. 이에 따라 의복 생산시의 총손실을 줄이기위한 상의, 하의생산시 필요한 부위별 최적규격치 간격을 제시하였다.적인 기능으로 보여지는 것에 좁혀서 작업능력의 연령증가 변화에 대하여다원적 평가를 하는 것이 실제적이라고 할 수 있다. 따라서 본 연구에서는 인간이 가지고 있는 다수의 기능중에서 수지교 치성과 연령증가와의 관계를 조사한다. 만약 연령증가 만으로 수지교치성을 평가 할 수 없는 경우에는 어떠한 요인이 수지기민성의 변화에 영향을 미치는가를 검토한다.t list)에서 자동적으로 사건들의 순서가 결정되도록 확장하였으며, 설비 제어방식에 있어서도 FIFO, LIFO, 우선 순위 방식등을 선택할 수 있도록 확장하였다. SIMPLE는 자료구조 및 프로그램이 공개되어 있으므로 프로그래머가 원하는 기능을 쉽게 추가할 수 있는 장점도 있다. 아울러 SMPLE에서 새로이 추가된 자료구조와 함수 및 설비제어 방식등을 활용하여 실제 중형급 시스