• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.281-286
• /
• 2007

Needs of fuel's performance evaluation for the dual-cooled fuel pellet (annular shape) necessitate the irradiation test in the test reactor. Irradiation test rig for the HARARO reactor, which is a special-purposed equipment used for material, irradiation and creep test, must satisfy the operational requirement on the hydraulic characteristics and structural integrity. In this paper, pressure drop and flow-induced vibration test for the newly developed non-instrumented test rig were carried out using FIVPET as a out-pile evaluation test. The test results show that the new test rig satisfy the HANARO operational requirement with sufficient margin. The spectral response characteristics of the flow-induced vibration of the test rid were also discussed.

• Journal of Aerospace System Engineering
• /
• v.12 no.2
• /
• pp.59-65
• /
• 2018

The landing gear (L/G) handle of an aircraft is an essential piece of equipment for aircraft take-off and landing. The bracket in the landing gear handle was fractured during a vibration test when developing the landing gear handle. This paper summarizes the vibration test procedures performed during landing gear handle development. A cause analysis, design improvements, and verification results of the fault in the vibration test are also provided.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.246-252
• /
• 2013

The vibration characteristics of railway vehicles are very complex because they are not only dependent on vehicle and track conditions but also on operating conditions. Vibration can cause the failure of rolling stock equipment. To verify that the quality of rolling stock equipment is acceptable, it should be able to withstand vibration tests of reasonable magnitude and duration. There are many standards for vibration and shock tests of equipment in Korea. In this paper, we have reviewed and compared the standards (KS R 9144, R 9146 and IEC 61373) for vibration and shock tests.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.64-68
• /
• 1998

본 연구의 목적은 수도권 지하철차량의 소음과 진동에 방음차륜(또는 탄성차륜)이 어느 정도의 효과를 가져오는가를 평가하기 위한 것이다. 실차시험을 통하여 일체차륜이 장착된 차량과 방음차륜이 장착된 차량의 차내소음 및 차체진동을 비교하여 보았다. 그 결과 방음차륜은 지하철차량의 소음과 진동에 효과가 있음을 알 수 있었다. 그러나 실제 적용은 소음과 진동 이외에도 여러 가지 측면에서의 검토가 이루어져야만 가능할 것이다.

• Journal of KSNVE
• /
• v.7 no.2
• /
• pp.247-254
• /
• 1997

In the case of a precision equipment, it requires a vibration free environment to provide its proper function. Especially, lithography and inspection devices, which have sub-nanometer class high accuracy and resolution, have come to necessity for producing more improved giga class semiconductor wafers. This high technology equipments require very strict environmental vibration standard in proportion to the accuracy of the manufacturing, inspecting devices. The vibration criteria are usually obtained either by the real vibration exciting test on the equipment or by the analytical calculation. This paper proposes a new method to solve this problem at a time. The permissible vibration level to a precision equipment can be easily obtained by analyzing a process of Frequency Response Function. This paper also demonstrates its effectiveness by applying the proposed method to finding the vibration criteria of a Computer Hard Disk Driver by Impact Test.

• Journal of KSNVE
• /
• v.6 no.3
• /
• pp.317-323
• /
• 1996

This paper proposes the method of experimental structural dynamic modification of fixture for environmental vibration test control. This method can predict the responses at any points on the fixture utilizing the experimental data, and structural dynamic modification of fixture is made using the predicted responses for the spectra at the specimen attachment points to meet the specified reference spectrum. From the results of controlling the fixture before and after modification by conventional control method and optimal reference spectrum, which has been previously reported by the authors, the proposed method is shown to be an effective one.

• Journal of KSNVE
• /
• v.5 no.4
• /
• pp.555-563
• /
• 1995

This paper proposes the method of antiresonance frequency analysis of multi-input multi-output system. The structural dynamic modification techniques by antiresonance frequency analysis are also applied to reduce the undertest at specimen attachment points on the fixture in environmental vibration test, which is resulted from the inconsistency of antiresonance frequencies at any specified points. Several computer simulations show that the proposed method can remove the undertest problem which is not removed in conventional vibration test control. And the effectiveness of the method is verified with the impact hammer excitation of aluminium fixture model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.764-767
• /
• 2002

본 논문은 인체진동 실험을 수행하는 연구자들이 필요한 표준절차를 소개한다. 국내 연구자들의 인체실험에 관한 보건과 안전(health and safety)에 대한 인식이 부족에서 발생할 수 있는 문제점들을 지적한다. 본 논문에서는 기존의 인체시험에 관련된 자료들(ISO 13090-1:1998(E)과 ISVR Technical Memorandum)을 비교 분석하여, 인체에 기계적인 진동을 수반하는 실험에 있어서 준수해야 할 실험의 절차들을 자세히 제시한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.5
• /
• pp.482-489
• /
• 2010

This paper describes the test procedure, instrumentation, verification methodology and the results of the ground vibration test(GVT) and force vibration test(FVT) of the SmartUAV aircraft to estimate experimentally dynamic characteristics of the aircraft. Bungee cords are used to emulate free-free boundary conditions of the test aircraft. The SmartUAV is excited by three shakers and one-hundred frequency response functions(FRF's) is measured. The FRF's are reduced and analyzed to identify the dynamics parameters of the SmartUAV. To extract modal parameters of the SmartUAV such as, natural frequencies and damping ratios, the poly-reference least square complex exponential method is used in the time domain. The mode shape coefficients are estimated with the least squares frequency domain method to identify the vibration modes. The FVT was performed by fixed sine frequency with three shakers on the x, y and z direction and vibration characteristics of structures and detail equipments are measured.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.26 no.3
• /
• pp.252-261
• /
• 2023

Analysis of dynamic characteristics and flight vibration test for unmanned aerial vehicles was studied by using dummy test body. The FEM model for dummy test body was supplemented by results of modal and random vibration test. The free end boundary condition to simulate flight environments was made by test setup using bungee cable. Prior to the flight vibration test using a dual electric vibration exciters, the test procedure to calculate quantitative vibration level was studied by using military specification. The actual test was successfully done by using the analysis and pretest results. From the analysis results, it was possible to determine the feasibility of the test by predicting the excitation force of the flight vibration test and to get the response of any point which could not be measured by the test. The results of this study will much contribute to the Test and Evaluation of unmanned aerial vehicles.