• Progress in Medical Physics
• /
• v.24 no.4
• /
• pp.237-242
• /
• 2013

In the intracranial regions, an accurate delineation of the target volume has been difficult with only the CT data due to poor soft tissue contrast of CT images. Therefore, the magnetic resonance images (MRI) for the delineation of the target volumes were widely used. To calculate dose distributions with MRI-based RTP, the electron density (ED) mapping concept from the diagnostic CT images and the pseudo CT concept from the MRI were introduced. In this study, the look up table (LUT) from the fifteen patients' diagnostic brain MRI images was created to verify the feasibility of MRI-based RTP. The dose distributions from the MRI-based calculations were compared to the original CT-based calculation. One MRI set has ED information from LUT (lMRI). Another set was generated with voxel values assigned with a homogeneous density of water (wMRI). A simple plan with a single anterior 6MV one portal was applied to the CT, lMRI, and wMRI. Depending on the patient's target geometry for the 3D conformal plan, 6MV photon beams and from two to five gantry portals were used. The differences of the dose distribution and DVH between the lMRI based and CT-based plan were smaller than the wMRI-based plan. The dose difference of wMRI vs. lMRI was measured as 91 cGy vs. 57 cGy at maximum dose, 74 cGt vs. 42 cGy at mean dose, and 94 cGy vs. 53 at minimum dose. The differences of maximum dose, minimum dose, and mean dose of the wMRI-based plan were lower than the lMRI-based plan, because the air cavity was not calculated in the wMRI-based plan. These results prove the feasibility of the lMRI-based planning for brain tumor radiation therapy.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.24 no.1
• /
• pp.20-26
• /
• 2020

Purpose It is intended to figure out the errors derived from changes in depth and volume when measuring the Standard source and ^99mTc-pertechnetate by using a Dose calibrator. Then recommend appropriate measurement depth and volume. Materials and Methods As a Dose calibrator, CRC-15βeta and CRC-15R (Capintec, New Jersey, USA) was used, and the measurement sources were ⁵⁷Co, ¹³³Ba, ¹³⁷Cs and ^99mTc-pertechnetate was also adopted due to its high frequency of use. The Standard source was respectively measured the changes according to its depth without changing the volume, in a range of 0 cm to 15 cm from the bottom of the ion chamber. ^99mTc-pertechnetate was measured at each depth by changing the volume with 0.1 mL, 0.3 mL, 0.5 mL, 0.7 mL and 0.9 mL Respectively. And the depth range was from 0 cm to 15 cm at the bottom of the ion chamber. Results In the case of Standard source ⁵⁷Co, ¹³³Ba, ¹³⁷Cs and ^99mTc-pertechnetate, there were significant differences according to the measurement depth(p<0.05). ^99mTc-pertechnetate has a negative correlation coefficient according to the depth, and the error of the measured value was negligible at a depth from 0 cm to 7 cm at 0.3 mL and 0.5 mL, and the range of error increased as the volume increased. Conclusion In clinical practice, it is sometimes installed differently than the Standard depth recommended by the equipment company. If it's measured at the recommended depth and volume, it could be thought that unnecessary exposure of the operator and the patient will be reduced, and more accurate radiation exams will be possible in quantitative analysis.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.152-161
• /
• 2023

In general, large-capacity hydrogen storage vessels, typically in the form of vertical cylindrical vessels, are constructed using steel materials. These vessels are anchored to foundation slabs that are specially designed to suit the environmental conditions. This anchoring method involves pre-installed anchors on top of the concrete foundation slab. However, it's important to note that such a design can result in concentrated stresses at the anchoring points when external forces, such as seismic events, are at play. This may lead to potential structural damage due to anchor and concrete damage. For this reason, in this study, it selected an vertical hydrogen storage vessel based on site observations and created a 3D finite element model. Artificial seismic motions made following the procedures specified in ICC-ES AC 156, as well as domestic recorded earthquakes with a magnitude greater than 5.0, were applied to analyze the structural behavior and performance of the target structures. Conducting experiments on a structure built to actual scale would be ideal, but due to practical constraints, it proved challenging to execute. Therefore, it opted for an analytical approach to assess the safety of the target structure. Regarding the structural response characteristics, the acceleration induced by seismic motion was observed to amplify by approximately ten times compared to the input seismic motions. Additionally, there was a tendency for a decrease in amplification as the response acceleration was transmitted to the point where the centre of gravity is located. For the vulnerable components, specifically the sub-system (support columns and anchorages), the stress levels were found to satisfy the allowable stress criteria. However, the concrete's tensile strength exhibited only about a 5% margin of safety compared to the allowable stress. This indicates the need for mitigation strategies in addressing these concerns. Based on the research findings presented in this paper, it is anticipated that predictable load information for the design of storage vessels required for future shaking table tests will be provided.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.13 no.3
• /
• pp.31-42
• /
• 2009

Purpose: As the number of domestic medical institutions installing PET/CT is increasing rapidly, the transfer of PET/CT images among medical institutions is also increasing. Thus, it is necessary to collect the comparative SUV data from several medical institutions' PET/CT systems through a phantom study which semi-quantitatively compares the SUV on one bed, the change scale of the SUV on the slices, and the time of measuring. The phantom study to find differences among the SUVs from various PET/CT offers the opportunity to obtain the reliability of the SUV in PET/CT images. Materials and Methods: Ten PET/CT systems from medical institutions in Korea were used. To obtain the accurate data, the study has been using the radiation detector of Korea Research Institute of Standards and Science to verify. The internal structures of NEMA $phantom^{TM}$ were removed and Six thousand milliliters of distilled water which has 1mCi of $^{18}F$-FDG put into the phantom. The water was properly integrated with $^{18}F$-FDG using magnetic stirrer. The images were acquired at 60, 70, 80, 90, 100, 110 and 120-minutes for 3 minute each. Two hundred square centimeters of region of interests were placed and analyzed. To confirm the usefulness, the correction-table came out from patients' data. Results: The coefficient of variability of the SUV from -11.0 to 9.90 % fell into the range of international standards(${\pm}10%$) along with the SUV on a bed, the change scale of the SUV on the slices, and the time of measuring, except one PET/CT system. Using the data of the differences among the SUVs, we came to withdraw the correction-table ranging from 0.803 to 1.246. The correction-table was confirmed its usefulness through Linear Regression Analysis which was applied to normal cases. Conclusions: Although studies have been made on the variation of the SUV, there is little attention on the standardization of the SUV. Based on this study of the quantitatively comparable data about the SUV accommodating the correction-table, it would help to have more corrective diagnosis.

• The Journal of Information Systems
• /
• v.25 no.1
• /
• pp.1-23
• /
• 2016

Purpose Self-congruity deals with the effect of symbolic value-expressive attributes on consumer decision and behavior, which is the theoretical foundation of the "non-utilitarian destination positioning". Functional congruity refers to utilitarian evaluation of a product or service by consumers. In addition, recent years, social network services, especially mobile social network services have created many opportunities for e-WOM communication that enables consumers to share personal consumption related information anywhere at any time. Moreover, self-construal is a hot and popular topic that has been discussed in the field of modem psychology as well as in marketing area. This study aims to examine the moderating effect of self-construal on the relationship between self-congruity, functional congruity and tourists' positive electronic word of mouth (e-WOM). Design/methodology/approach In order to verify the hypotheses, we developed a questionnaire with 32 survey items. We measured all the items on a five-point Likert-type scale. We used Sojump.com to collect questionnaire and gathered 218 responses from whom have visited Korea before. After a pilot test, we analyzed the main survey data by using SPSS 20.0 and AMOS 18.0, and employed structural equation modeling to test the hypotheses. We first estimated the measurement model for its overall fit, reliability and validity through a confirmatory factor analysis and used common method bias test to make sure that whether measures are affected by common-method variance. Then we tested the hypotheses through the structural model and used regression analysis to measure moderating effect of self-construal. Findings The results reveal that the effect of self-congruity on tourists' positive e-WOM is stronger for tourists with an independent self-construal compared with those with interdependent self-construal. Moreover, it shows that the effect of functional congruity on tourists' positive e-WOM becomes salient when tourists' self-construal is primed to be interdependent rather than independent. We expect that the results of this study can provide important implications for academic and practical perspective.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.848-857
• /
• 2018

Recently, around the world, active development of new renewable energy sources including solar power, waves, and fuel cells, etc. has taken place. Particularly, floating offshore wind farms have been developed for saving costs through large scale production, using high-quality wind power and minimizing noise damage in the ocean area. The development of floating wind farms requires an evaluation of the Maritime Safety Audit Scheme under the Maritime Safety Act in Korea. Floating wind farms shall be assessed by applying the line and area concept for systematic development, management and utilization of specified sea water. The development of appropriate evaluation methods and standards is also required. In this study, proper standards for marine traffic surveys and assessments were established and a systemic treatment was studied for assessing marine spatial area. First, a marine traffic data collector using AIS or radar was designed to conduct marine traffic surveys. In addition, assessment methods were proposed such as historical tracks, traffic density and marine traffic pattern analysis applying the line and area concept. Marine traffic density can be evaluated by spatial and temporal means, with an adjusted grid-cell scale. Marine traffic pattern analysis was proposed for assessing ship movement patterns for transit or work in sea areas. Finally, conceptual design of a Marine Traffic and Safety Assessment Solution (MaTSAS) was competed that can be analyzed automatically to collect and assess the marine traffic data. It could be possible to minimize inaccurate estimation due to human errors such as data omission or misprints through automated and systematic collection, analysis and retrieval of marine traffic data. This study could provides reliable assessment results, reflecting the line and area concept, according to sea area usage.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.21 no.3
• /
• pp.121-134
• /
• 2019

This study was conducted to review the trends of forest meteorological studies based on the publications for last 20 years in Korean Journal of Agricultural and Forest Meteorology (KJAFM), and to provide insight for future prospect for researches in the field of forest meteorology. A total of 220 papers related to forest meteorology were published in KJAFM for the last 20 years. That corresponds to 33.5% out of all the papers including agricultural meteorology papers. To review the trends of forest meteorology studies, the 220 published papers were classified into seven categories. They are forest meteorology and forest fire, forest meteorology and tree physiology, forest meteorology and forest protection, micrometeorology in mountain area, climate and forest growth, climate and forest vegetation distribution, and climate change and forest ecosystem. Even if there were differences in paper numbers among the seven categories, it was found that various and very specific studies were conducted in the field of forest meteorology for the last 20 years. It was also expected that the accumulation and utilization of various and accurate forest meteorological information would bring remarkable progress of forest meteorological studies in the near future.

• Journal of the Korean Society of Radiology
• /
• v.13 no.1
• /
• pp.111-118
• /
• 2019

Chest digital tomosynthesis has become a practical imaging modality because it can solve the problem of anatomy overlapping in conventional chest radiography. However, because of both limited scan angle and finite-size detector, a portion of chest cannot be represented in some or all of the projection. These bring a discontinuity in intensity across the field of view boundaries in the reconstructed slices, which we refer to as the truncation artifacts. The purpose of this study was to reduce truncation artifacts using a weighted normalization approach and to investigate the performance of this approach for our prototype chest digital tomosynthesis system. The system source-to-image distance was 1100 mm, and the center of rotation of X-ray source was located on 100 mm above the detector surface. After obtaining 41 projection views with ${\pm}20^{\circ}$ degrees, tomosynthesis slices were reconstructed with the filtered back projection algorithm. For quantitative evaluation, peak signal to noise ratio and structure similarity index values were evaluated after reconstructing reference image using simulation, and mean value of specific direction values was evaluated using real data. Simulation results showed that the peak signal to noise ratio and structure similarity index was improved respectively. In the case of the experimental results showed that the effect of artifact in the mean value of specific direction of the reconstructed image was reduced. In conclusion, the weighted normalization method improves the quality of image by reducing truncation artifacts. These results suggested that weighted normalization method could improve the image quality of chest digital tomosynthesis.

• Journal of The Korean Association For Science Education
• /
• v.25 no.7
• /
• pp.746-753
• /
• 2005

In order to be efficient teachers should understand the current level of leaners through diagnostic evaluation. However, it is arduous to administer a diagnostic examination in every class because of various limitations. This study examined, the major issues arising from the development of a new science diagnostic evaluation system by incorporating the using knowledge state analysis method. The proposed evaluation system was based on the knowledge state analysis method. Knowledge state analysis is a method where by a distinguished collection of knowledge uses the theory of knowledge space. The theory of knowledge space is very advantageous when analyzing knowledge in strong hierarchies like mathematics and science. It helps teaching plan through methodically analyzing a hierarchy viewpoint for students' knowledge structure. The theory can also enhance objective validity as well as support a considerable amount of data fast by using the computer. In addition, student understanding is improved through individualistic feedback. In this study, an evaluation instrument was developed that measured student learning outcome, which is unattainable from the existing method. The instrument was administered to pre-service physics teachers, and the results of student evaluation was analyzed using the theory of knowledge space. Following this, a revised diagnostic evaluation system for facilitating student individualized learning was constructed.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.9
• /
• pp.130-139
• /
• 2007

The disaster from functional gastrointestinal disorders (FGID) has detrimental impact on the quality of life of the affected population. There are, however, rare diagnostic methods for FGID. Our research group identified recently that the gastrointestinal tract well of the patients with FGID became more rigid than that of healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. The objective of the current study is, therefore, to identify feasibility of a diagnostic system for FGID based on ultrasound technique, which can quantify the characteristics above. Two-dimensional finite difference (FD) models (one normal and two rigid models) were developed to analyze the reflective characteristic (displacement) on each soft-tissue layer responded after application of ultrasound signals. Based on the results from FD analysis, the ultrasound system for diagnosis of the FGID was developed and clinically tested via application of it to 40 human subjects with/without FGID who were assigned to Normal and Patient Groups. The results from FD analysis showed that the maximum displacement amplitude in the rigid models (0.12 and 0.16) at the interface between the fat and muscle layers was explicitly less than that in the normal model (0.29). The results from actual specimens showed that the maximum amplitude of the ultrasound reflective signal in the rigid models $(0.2{\pm}0.1Vp-p)$ at the interface between the fat and muscle layers was explicitly higher than that in the normal model $(0.1{\pm}0.0Vp-p)$. Clinical tests using our customized ultrasound system showed that the maximum amplitudes of the ultrasound reflective signals near to the gastrointestinal tract well for the patient group $(2.6{\pm}0.3Vp-p)$ were generally higher than those in normal group $(0.1{\pm}0.2Vp-p)$. These findings suggest that our customized ultrasound system using the ultrasound reflective signal may be helpful to the diagnosis of the FGID.