• Smart Media Journal
• /
• v.8 no.1
• /
• pp.51-58
• /
• 2019

This paper describes a gesture application to controlling the special effects of physical devices for 4D contents using the PWM (Pulse Width Modulation) method. The user operation recognized by the infrared sensor is interpreted as a command for 3D content control, several of which manipulate the device that generates the special effect to display the physical stimulus to the user. With the content controlled under the NUI (Natural User Interface) technique, the user can be directly put into an immersion experience, which leads to provision of the higher degree of interest and attention. In order to measure the efficiency of the proposed method, we implemented a PWM-based real-time linear control system that manages the parameters of the motion recognition and animation controller using the infrared sensor and transmits the event.

• Korean Journal of Optics and Photonics
• /
• v.17 no.3
• /
• pp.223-230
• /
• 2006

We demonstrate a distributed fiber sensor system based on spatially-selective Brillouin scattering, using a single laser diode as a light source whose optical frequency is directly modulated by the injection current. The pump and the counter-propagating probe lights, which are sinusoidally frequency-modulated, are superposed in the fiber so that stimulated Brillouin scattering takes places only at a specific location along the fiber. Brillouin gain peak position is controlled by varying the modulation frequency. Distributions of Brillouin shift frequency are measured for the case of concatenated optical fibers of two different kinds and also for the case of temperature distribution. The temperature coefficient of the Brillouin shift frequency is measured to be $1.33MHz/^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.8
• /
• pp.51-57
• /
• 2004

We have analyzed the effect of out-band dispersion in the cascaded fiber Bragg Elating(FBG) based optical add-drop multiplexers(OADM) when bypassed wavelengths contain SCM signals. In order to compute this impairment the dispersion characteristics of FBG have been analytically calculated by solving their coupled wave equations, and the Fourier method is applied to IMD analysis. The out-band dispersion effects over WDM/SCM signals are analyzed under different and common system situations as: ITU channel spacing(100, 50, 25 GHz), channel density parameter, frequency extension of the SCM plan, modulation characteristics, FBG length, etc. From this results, the transport of WDM/SCM signals in future DWDM transport networks could be limited by this effect which has to be taken into account for designing future networks.

• Convergence Security Journal
• /
• v.23 no.1
• /
• pp.19-25
• /
• 2023

The current network environment provides a real-time interactive service from an initial one-way information prov ision service. Depending on the form of web-based information sharing, it is possible to provide various knowledge a nd services between users. However, in this web-based real-time information sharing environment, cases of damage by illegal attackers who exploit network vulnerabilities are increasing rapidly. In particular, for attackers who attempt a phishing attack, a link to the corresponding web page is induced after actively generating a forged web page to a user who needs a specific web page service. In this paper, we analyze whether users directly and actively forge a sp ecific site rather than a passive server-based detection method. For this purpose, it is possible to prevent leakage of important personal information of general users by detecting a disguised webpage of an attacker who induces illegal webpage access using traceback information

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.12
• /
• pp.1258-1268
• /
• 2014

In this paper, we propose and design IBFD system based on DCR. And then, we analyze effect of DC offset by self-interference in the proposed system. Also, we evaluate BER performance of the proposed system according to DC offset. As a result of the simulation, we can confirm that when the self-interference is not completely cancelled by the RF cancellation, linearity of desired signal and self-interference is distorted by DC offset. Also, in the proposed system using m-QAM modulation, DC offsets of multi-level are caused by self-interference with m-QAM modulation. As a result, constellations of desired signal and self-interference are greatly distorted. In contrast, in the proposed system using m-PSK modulation, DC offset of single level is caused by self-interference with m-PSK modulation. In this condition, we confirm that distortion of constellations of desired signal and self-interference is less than when using m-QAM modulation. That is, we can confirm that m-PSK modulation is effective than m-QAM modulation in DCR based IBFD system. Also, we can confirm that it is important to cancel self-interference as much as possible in RF-stage.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.3 s.345
• /
• pp.59-67
• /
• 2006

OFDM (Orthogonal frequency Division Multiplexing) systems convert serial data stream to N parallel data streams and modulate them to N orthogonal subcarriers. Thus spectrum utilization efficiency of the OFDM systems are high and high-speed data transmission is possible. However, with the OFDM systems using the same modulation method at all subcarriers, the error probability is dominated by the subcarriers which experience deep fades. Therefore, in order to enhance the performance of the system adaptive modulation is required, with which the modulation methods of the subcarriers are determined according to the estimated SNRs. The IEEE 802.11a system selects various transmission speed between 6 and 54 Mbps according to the modulation mode. There are three typical methods for SNR estimation: Direct estimation method uses the frequency domain symbols to estimate SNR directly by minimizing MSE (Mean Square Error), EVM method utilizes the distance between the demodulated constellation points and received complex values, and the method utilizing the Viterbi algorithm uses the cumulative minimum distance in decoding process to estimate the SNR indirectly. Through comparison analyses of three methods we propose a new SNR estimation method, which employs both the EVM method and the Viterbi algorithm. Finally, we perform extensive computer simulations to confirm the performance improvement of the proposed adaptive OFDM systems on the basis of IEEE 802.11a.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.3
• /
• pp.517-526
• /
• 2000

In this paper, we propose the trellis coded spread spectrum communication system with one channel signal selection of the subset by the PN code. This paper proposes the Viterbi decoder that have the squared Euclidean distance of the order phase difference as well as 1st order phase difference as the branch metrics by using the multiple symbol detection method. TCM method was developed to overcome limited power and bandwidth efficiently in digital communication. we multiply one of convolution code's output data to PN code for applying TCM to the spread spectrum. We investigated the performance of the direct sequence/spread spectrum communication system with trellis coded modulation. In this system, we could improved the coding gain in the spread spectrum.

• Journal of the Institute of Convergence Signal Processing
• /
• v.1 no.2
• /
• pp.131-137
• /
• 2000

In this paper, as a compatible software radio transmission system, Digital-Radio conversion system which can directly change the digital signal generated by the logic circuit into radio signal is proposed. By the vector synthesis method, the digital signals can change directly into radio signal. If such a circuit is realized, RF circuit and an antenna can be composed by the simple one device, and the radio is directly controlled and performed by the software processing which is the essence of software radio. This Digital-Radio conversion system of this paper give many number of communication channels being offered by PN code and offer a hardware design flexibility by digitization, therefore it decrease the percentage ratio of hardware of system and give a more flexible function of software basis. In this paper, the principle of digital to radio signal generation algorithm is explained and the performance characteristics of proposed algorithm is shown in time base by the computer simulation method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.6
• /
• pp.610-617
• /
• 2011

This paper proposes a novel and direct dead-time compensation method of the 3-phase inverter using space vector pulse width modulation(SVPWM) topology. The proposed dead-time compensation method directly compensates the dead-time to the turn-on time of the effective voltage vector according to the current direction of the medium voltage reference. Each phase voltages are determined by the switching times of the effective voltage vectors, and the practical switching times have loss according to the current direction by the dead-time effect in the 3-phase inverter. The proposed method adds the dead-time to the switching time of the effective voltage vector according to the current direction, so it does not require complex d-q transform and controller to compensate the voltage error. The proposed dead-time compensation scheme is verified by the computer simulation and experiments of 3-phase R-L load.

• Korean Journal of Optics and Photonics
• /
• v.31 no.6
• /
• pp.259-267
• /
• 2020

We evaluate the degradation of receiver sensitivity induced by direct and indirect exposure to solar irradiance in free-space optical communication systems. For this purpose, we calculate the variances of numerous noise components arising from solar irradiance, and then estimate the receiver sensitivity penalties for intensity-modulation/direct-detection and coherent systems. The results show that the penalties are less than 1.3 dB when indirect sunlight impinges on the detector, regardless of the system. However, the sensitivity penalties are estimated to be larger than 30 dB when the sunlight is directly incident upon the receiver. These penalties are barely reduced if we insert an optical polarizer, or if we adjust the bandwidth of an optical filter at the receiver to be as narrow as the signal's bandwidth.