• 동력기계공학회지
• /
• 제6권3호
• /
• pp.11-16
• /
• 2002

This paper describes the power performance and emission characteristics of the high speed direct injection diesel engine (2.9 litter displacements) driven by soybean oil asknown a bio diesel fuel. The results were compared to diesel fuel with blending bio diesel fuels. The soybean bio diesel fuel was added in the diesel fuel in concentration varying from 25% to 75% volume rates. We measured the emissions according to ECE 13 mode and full load, fixedengine speed. When the 25% bio diesel fuel was used, NOx emission at the ECE 13 mode test slightly decreased compared with diesel base engine. Over engine speed of 2000 rpm, the level of unburned hydrocarbon(HC) and carbon monoxide(CO) were the same to the diesel engine. Smoke emission decreased asthe blending bio diesel fuel rate increased.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.54-65
• /
• 1999

In this study, the flow field, spray structure, and combustion process were investigated in a direct injection diesel engine having an offset bowl in a combustion chamber. The KIVA-3V code was used in this study. In order to obtain accurate results, a droplet atomization model, wall impingement model, and ignition delay concept were added to KIVA-3V code. The results showed that the offset bowl engine had a large vortex flow. The direction of this flow counteracted to the direction of fuel injection in one side of combustion chamber. It decreased local turbulent kinetic energy and eventually nonuniform combustion was resulted in an offset bowl engine. In comparison with a center bowl engine case, the peak cylinder pressure was decreased about 6%. Finally , the effect of swirl on combustion was investigated in an offset bowl engine . As the became stronger, the nouniform characteristics in combustion were increased.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
• /
• pp.49-59
• /
• 2002

For the purpose of helping development of a GDI(Gasoline Direct Injection) engine, the spray behaviors and fuel distributions were investigated in a single cylinder GDI engine. The experimental engine is a swirl type GBI engine with a SCV(Swirl Control Valve). PLIF(Planar Laser Induced Fluorescence) system with KrF Excimer laser was used for the measurement of the fuel distributions. The effects of SCV opening angle and the Injector specifications, such as the spray cone angle and the offset an91e on the fuel distributions characteristics were investigated. As a result, it was found that the SCV opening angle had a great effect on the fuel distributions in the late stage of compression process by changing flow fields in the combustion chamber.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.99-106
• /
• 1999

The present study deals with the effect of combustion chamber shape on in-cylinder soot oxidation characteristics of a D.I . diesel engine. The analysed combustion chambers were a toroidal and a reentrant with a projection(Complex). The two-color method was used to measure in-cylinder flame temperature and KL value which is approximately proportional to the soot amount along the optical path. In addition, heat release rate was calculated from the in-cylinder pressure data. From these investigations , the soot oxidation of the reentrant and the complex which were strengthen squish flows went worse in late combustion period under heavy-load operation compared to that of the toroidal at retarded fuel injection timing . It might be the cause of the flame holding that squish lip depress the outflow of flame from the bowl to the entire combustion space.

• 동력기계공학회지
• /
• 제8권1호
• /
• pp.18-23
• /
• 2004

The direct injection diesel engine is one of the most efficient thermal engines. For this reason DI diesel engines are widely used for heavy-duty applications. But the world is faced with very serious problems related to the air pollution due to the exhaust emissions of diesel engine. So, that is air pollution related to exhaust gas resulted from explosive combustion should be improved. Exhaust Gas Recirculation(EGR) is a proven method to reduce NOx emissions. In this study, the experiments-were performed at various engine loads while the EGR rates were set from 0% to 20%. The emissions trade-off and combustion of diesel engine are investigated. Hot and cooled EGR are achieved without cooling and with cooling respectively. It was found that the exhaust emissions with the EGR system resulted in a very large reduction in oxides of nitrogen at the expense of higher smoke emissions. Also, the reduction rates of NOx emissions for hot and cooled EGR are similar at load 20%.

• 한국자동차공학회논문집
• /
• 제8권4호
• /
• pp.42-50
• /
• 2000

Drop size distribution of an air-assisted fuel injector(AAFI) was investigated. Influence of parameters such as ambient air density supply pressure and air-liquid mass ratio(ALR) was examined through both measurement and analysis. The Sauter mean diameter$D_{32}$ varied from 9 to 25$\mu$m throughout all experimental conditions. An empirical correlation for droplet size was obtained. Analytical correlations for predicting $D_{32}$ with respect to operating conditions were also derived through energy consideration and introduction of a simplified model of the from the empirical fitting was adapted to the original equation the proposed correlation in this study matched more closely with measured results. The current correlation exhibited a favorable study matched more closely with measured results. The current correlation exhibited a favorable prediction for $D_{32}$ compared to that by the empirical correlation at selected experimental conditions so that it may be used to predict atomization performance of the AAFI at operating conditions which was not covered in the measurements. After validation the analytical equation was applied to survey the feasible operating conditions for gasoline direct injection application.

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.30-39
• /
• 2001

The direct injection into the cylinders has been regarded as a way of the reduction in fuel consumption and pollutant emissions. The spray produced by the high pressure injector is of paramount importance in DISI(Direct Injection Spark Ignition) engines in that the primary atomization process must meet the requirement of quick and complete evaporation, mixing with air and combustion especially to prohibit the excessive HC emissions. The interaction between air flow and fuel spray was investigated in a steady flow system embodied in a wind tunnel to simulate the variety of flow inside the cylinder of the DISI engine. The direct Mie scattered and shadowgraph images presented the macroscopic view of the liquid sprays and vapor fields. The velocity and particle size of fuel droplets were investigated by phase doppler anenometer(PDA) system. The processes of atomization and evaporation with a DISI injector were observed and consequently utilized to construct the data-base for the spray and fuel-air mixing mechanism as a function of the flow characteristics.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2245-2250
• /
• 2003

Particulate matters(PM) have bad effect on the health. We carried out measurements of diesel PM under $10{\mu}m$ diameter from a HSDI diesel engine with a diesel oxidation catalyst(DOC) by using the ELPI. This paper compares the two results of the smoke level and the PM level of masses and numbers. We also investigated the effect of the DOC. Under high speed and load, HSDI diesel engine exhausts much masses of particulate matters over 100nm diameter, and a number of PM from 7 to 100nm diameters at the same condition. DOC could reduce the total mass of the PM. However, the DOC could increase the number of ultra fine PM. Before light-off of the soot, the DOC absorb the PM and the DOC oxidize the PM after light-off temperature. The fine PM could be made during the oxidation. Therefore, the advanced DOC is needed to reduce the number of the fine PM.

• 대한기계학회논문집B
• /
• 제38권6호
• /
• pp.475-482
• /
• 2014

본 연구는 스프레이 열전달을 이용한 저온도차 스털링 엔진의 실험적 개념 연구를 제시한다. 스프레이 열교환기는 노즐을 통하여 엔진 작동 공간에 직접 물을 분사함으로써 엔진 성능을 저해하는 불용 공간을 최소화하고 열전달 효율을 높였다. 직접 구현된 실험 스털링 엔진의 실증 실험은 운전 시점의 기동 특성, 정상 상태의 운전 특성, 엔진의 출력 특성에 대하여 진행하였다. 실험 결과, 열수 유량 증가에 대하여 엔진 기동 시 작동 최소 온도는 감소한 반면, 고온부 온도와 고온부-저온부 온도차는 대체로 일정하였다. 정상 상태 운전의 경우 열수 온도 및 유량 증가에 대하여 작동 주파수는 증가하였다. 엔진 출력은 열수 온도 및 유량 증가에 따라 사이클당 일 및 작동 주파수 증가로 인하여 증가하였다. 본 연구에서 구현된 실험 스털링 엔진은 열수 유량 30 ml/min, 열수 온도 $65^{\circ}C$, 고온부-저온부 온도차 $6^{\circ}C$ 이상에서 엔진 출력 0.05W 수준으로 안정된 기동 및 운전 특성을 보였으며, 향후 출력 증가 및 다양한 적용 연구를 지속할 계획이다.

• 한국가스학회지
• /
• 제27권3호
• /
• pp.1-10
• /
• 2023

산업혁명의 발달로 인해 급격하게 증가된 온실가스 배출량을 저감하기 위해 배기 배출물 규제가 계속해서 강화되고 있다. 이를 만족시키기 위해선 친환경 연료의 사용은 필수적이다. 미래의 친환경 연료로서 수소가 주목받고 있지만, 물질적 특성으로 인해 취급과 보관에 큰 어려움을 겪고 있어, 이에 대안으로 암모니아가 제안되었다. 암모니아는 수소 대비 상온 조건에서 쉽게 액화가 가능하며, 에너지밀도가 높다. 이에 엔진의 연료로서 암모니아의 적용성을 검토하기 위해 직접분사식 암모니아 전소 엔진에서 연소제어인자의 변경에 따른 실험을 진행하였다. 본 실험은 점화시기(Spark Timing)와 공기과잉률(Excess Air Ratio) 두 개의 변수를 변경하여 실험을 진행하였다.엔진 속도 1,500 RPM 및 중부하 이상(제동 토크 200 Nm)의 조건에서 암모니아 전소를 하였을 때, 연소 안정성과 질소산화물, 미연 암모니아 등의 배기 배출물의 경향을 관찰하였다. 연소제어인자의 최적화를 통해 암모니아만을 연료로 사용한 경우에도 안정적인 연소가 가능한 조건을 찾을 수 있었고, 향후 운전영역 확장을 위한 전략을 적용할 계획이다.