• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.55-64
• /
• 2014

This work was investigated on pilot injection strategy of blended fuels(Diesel-DME) for combustion and emissions in a single cylinder direct injection compression ignition engine. Diesel and DME were blended by the method of weight ratio. Weight ratios for diesel and DME were 95:05 and 90:10 respectively. dSOI between main and pilot injection timing was varied. A total amount of injected fuels(single injection) was adjusted to obtain the fixed BMEP as 4.2 bar in order to compare with the fuel conditions. Also, the amount of pilot injection fuel was varied by 5%, 10% and 20% of total injection fuel. The engine was equipped with common rail and injection pressure is 700 bar at 1200 rpm. As a result, when mixing ratio increase, indicated thermal efficiency was increased in comparison with DD 100 and CO, THC and smoke were lower than DD 100. The influence of reducing NOx by pilot injection was more effective than DD 100. When pilot injection quantity increase, abrupt increase of NOx was occured at pilot injection quantity of 20%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.78-85
• /
• 2007

Recently, diesel vehicles have been increased and their emission standards have been getting strict. The emission of diesel vehicles contains numerous dangerous compounds, especially particulate matters cause a serious environmental pollutant and affect to human health seriously. Thousands of studies have already reported that particulate matters are associated with respiratory and cardiovascular diseases, and death. Due to these, it is necessary to measure the soot concentration and soot particle size in laboratory flames or practical engines to recognize the soot formation, and develop the control strategies for soot emission. In this study, the characteristics of exhausted soot particle size and volume fraction from 2.0L CRDI diesel engine have been investigated as varying engine speed and load. Laser induced incandescence has been used to measure soot concentration. Time-resolved laser induced incandescence has been used to determine soot particle size in the engine. The soot volume fraction is increased as increasing engine load but soot volume fraction is decreased as increasing engine speed. The primary particle size is distributed about $35nm{\sim}60nm$ at each experimental conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.187-196
• /
• 1996

In this study, 3-dimensional finite element model of a diesel engine cylinder head was made to accomplish heat transfer analysis and also thermal stress and deformation analysis. Heat release analysis and Nusselt-Reynolds correlations were applied to determine the convective boundary conditions which are required for heat transfer analysis to calculate temperature distribution. Thermal stress distribution was also investigated from heat transfer analysis results. Steady state temperature and heat flux were measured by using K-type thermocouples and then compared with numerical results to give a guarantee for the propriety of numerical analyses.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.78-85
• /
• 2000

This study is to develop the diesel engine which has 6 cylinder natural aspiration direct injection type of 7.4$\ell$ with high performance, low emissions and low fuel consumption Finally the developed engine meets Korean `98 exhaust emission regulation for the city bus of heavy duty diesel engine by optimizing the various combustion parameters affecting performance and exhaust emissions. Combustion parameters are the swirl ratio of intake ports, the profile of injection pump`s cam affecting injection pressure, the design features of piston bowl of injection pump`s cam affecting injection pressure, the design features of piston bowl of combustion chamber and injector`s hole size. Through experimental analysis, various combustion parameters are optimized and the results are as follows; the swirl ratio is 2.20, the profile of injection pump`s cam is concave and re-entrant ratio, inner diameter of piston bowl and hole diameter of injector is 0.88,$\psi$64.0mm and $\psi$0.25mm respectively.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.60-60
• /
• 2017

화석연료의 고갈과 환경오염이 문제시 되면서 친환경 에너지개발에 대한 연구가 진행되고 있다. 그중 바이오디젤은 동,식물성유지 및 폐식용유를 이용하여 생산이 가능할뿐더러 농용엔진에 특별한 개조 없이 사용가능하다. 또한 바이오디젤 자체에 산소를 함유하고 있어 이산화탄소 저감에 효율적이다. 바이오 디젤에 관한 많은 연구가 수행되었으며, 기존의 연구는 단일유지의 폐식용유를 사용하여 바이오디젤을 생산하는 연구가 진행되었다. 하지만 가정에서 배출되는 식물성 폐식용유의 경우 여러 가지가 혼합되어 배출되고 있어, 혼합폐식용유지의 바이오디젤 특성평가가 필요하다. 따라서 본 연구에서는 폐식물성유지(폐대두유, 폐카놀라유, 폐해바라기유)를 중량비(1:4, 1:1.5 1:0.66, 1:0.25)로 혼합하여 바이오디젤을 생산하고, 생산한 바이오디젤을 농용기관에 이용하여 농용기관의 출력특성 및 배기배출물특성 평가를 실시하였다. 실험에 사용된 농용기관은 배기량이 673cc인 직접분사식 디젤기관(ND10DE, Daedong, Korea)이며, 엔진성능평가를 위해 토크는 토크센서(YDL-704s, Setech, Korea)를 사용하였다. 배기배출물 평가는 배기가스분석기(HG-550, Airlex, Germany)를 이용하여 이산화탄소, 질소산화물을의 배출량을 측정하였다. 폐식용유를 이용하여 생산한 바이오디젤과 경유의 기관성능을 비교한 결과 토크와 축출력의 경우 BD의 혼합량이 증가할수록 줄어들었다. 토크는 혼합된 유지에 따라 상용운전범위인 1500rpm~2400rpm에서 평균 대두와 카놀라유를 혼합하여 생산한 BD10은 7.2%, BD20은 12.1% 감소하였고, 대두와 해바라기유를 혼합하여 생산한 BD10은 11.3% BD20은 16.3% 감소하였다. 또한 해바라기와 카놀라유를 혼합하여 생산한 BD10은 8.3%, BD20은 14.6% 감소하였다. 이는 BD의 발열량이 경유에 비해 낮아 토크가 감소한 것으로 판단된다. 또한 배기배출물 평가의 경우 질소산화물은 BD의 함랑이 증가함에 따라 경유에 비해 배출량이 증가하는 경향을 보였고, 이산화탄소는 저감되는 것으로 나타났다. 이는 바이오디젤이 함산소연료이므로, 연료내의 산소로 인해 완전연소를 촉진시켜 이산화탄소를 저감시키고 질소산화물은 증가된 것으로 판단된다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.26-31
• /
• 2006

An experimental investigation of an early injection strategy was conducted on a small single cylinder common-rail DI diesel engine to reduce the oxides of nitrogen($NO_x$) emission. The main objectives of this study were to investigate the emissions, performance and combustion characteristics in a diesel engine with early and two-stage injections. The two- stage injection was conducted to reduce the wall-wetting of early injected fuels on the cylinder wall or to promote the ignition of premixed charge. The engine test was performed at conditions of 1500rpm, injection timing ranging from TDC to BTDC $80^{\circ}$. The experimental results show that $NO_x$ emissions were decreased in both cases of early injection and two stage injection compared to the conventional diesel combustion by the near TDC injection. However, soot and products of incomplete products (i.e. HC and CO) are slightly increased. Also, the second injection near TDC promoted the ignition of premixed fuel, therefore, IMEP was increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.105-113
• /
• 2014

Spray and combustion process with waste cooking oil (WCO) biodiesel and commercial diesel were analyzed in an optically-accessible single-cylinder compression ignition diesel engine equipped with a high pressure common-rail injection system. Direct imaging method was applied to investigate spray and combustion characteristics. From the mie-scattering results, it was verified that WCO biodiesel had a longer injection delay compared to diesel. Spray tip penetration length of WCO biodiesel was longer and spray angle was narrower than those of diesel due to poor atomization characteristics. In terms of combustion, WCO biodiesel showed later start of combustion, while flame was vanished more rapidly. Analysis of flame luminosity showed that WCO biodiesel combustion had lower intensity and lasted for shorter duration.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1045-1050
• /
• 2014

$N_2O$(Nitrous Oxide) is known as the third major GHG(Green House Gas) following $CO_2$(Carbon Oxide) and $CH_4$(Methane). The GWP(Global Warming Potential) factor of $N_2O$ is 310 times as large as that of $CO_2$ because $N_2O$ in the atmosphere is very stable, and it becomes a source of secondary contamination after photo-degradation in the stratosphere. Investigation on the cause of the $N_2O$ formation have been continuously reported by several researchers on power sources with continuous combustion form, such as a boiler. However, in the diesel engine, research on $N_2O$ generation which has effected from fuel components has not been conducted. Therefore, in this research, author has investigated about $N_2O$ emission rates which was changed by nitrogen and sulfur concentration in fuel on the diesel engine. The test engine was a 4-stroke direct injection diesel engine with maximum output of 12 kW at 2600rpm, and operating condition of that was set up at a 75% load. Nitrogen and sulfur concentrations in fuel were raised by using six additives : nitrogen additives were Pyridine, Indole, Quinoline, Pyrrol and Propionitrile and sulfur additive was Di-tert-butyl-disulfide. In conclusion, diesel fuels containing nitrogen elements less than 0.5% did not affect $N_2O$ emissions in the all concentrations and kinds of the additive agent in the fuel. However, increasing of the sulfur additive in fuel increased $N_2O$ emission in exhaust gas.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.140-156
• /
• 1997

The combustion characteristics of DI Diesel engine using turbocharging and EGR are numerically studied. Computations are carried out for the wide range of trubochyarged pressures, EGR ratios, and Ar/He dilution. Numerical results indicate that the Ar/He dilution in the intake gas significantly influence the engine performance, the spray combustion process, and the pollutant formation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.40-47
• /
• 2000

A model for the prediction of combustion and exhaust emissions of DI diesel engine has been formulated and developed. This model is a quasi-dimensional phenomenological one and is based on multi-zone combustion modelling concept. This model is developed based on the concept of Hiroyasu's multizone combustion models. It takes nozzle injection (spray) parameters, induction swirl into consideration and the models of zone velocity, air entrainment, fuel droplet evaporation and mixture combustion are upgraded. Various parameters, such as cylinder pressure, heat release rate, Nox and soot emission, and these parameters in the zone are simulated. The results are compared with the experimental ones, too.