• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.508-514
• /
• 2013

Substrate integrated waveguide(SIW) constructed by two metal planes and conductive vias in a dielectric substrate, have all the conductors connected each other and hence, cannot be biased by DC sources. We propose a new folded corrugated substrate integrated waveguide(FCSIW) that can be DC-biased. Since the proposed FCSIW replaces the SIW conducting vias by folded open subs, it can supply the DC sources. The FCSIW has better transmission characteristics and 30 % less width than the common corrugated substrate integrated waveguide(CSIW) having a serious leakage generation problem. The FCSIW shows better insertion loss(1.49 dB) compared with that(3.08 dB) of the CSIW measured for 154 mm length devices and averaged at 9~15 GHz frequency band. No leakage has been observed from crosstalk measurements of the FCSIW.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.36-43
• /
• 2004

In this paper, the frequency spectra from respective mechanical noise signals detected using ultrasonic wave and AE(Acoustic Emission) sensor were analysed to under spark generation between brush and commutator side with arbitrarily 15$^{\circ}$ rotation for brush from the DC motor in operation. Also, the frequency spectra from respective magnetizing noise signals detected using ultrasonic wave and AE sensor were analysed to under neutral point for brush from the DC motor in normal operation. And the analyses and comparison between the mechanical noise signal and magnetizing noise signal of ultrasonic wave with brush location change from the DC motor in operation. As the experimental results, tile mechanical noise signal of ultrasonic wave under spark generation between brush and commutator side with brush location change from the DC motor in operation were increased about 2.5∼3.0 times than magnetizing noise signal of ultrasonic wave form the DC motor in normal operation. Also, the main frequency band for mechanical noise signals of AE under spark generation between brush and commutator side with brush location change from the DC motor in operation, appeared about 1.3[MHz]∼l.5[MHz] by the fast fourier transform.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.6
• /
• pp.138-146
• /
• 2010

DC railway power supply system generally uses the running rails as negative-polarity return conductor for traction load current, and the induced rail potential and stay current cause serious problems to any electrified matter in the underground and also safety problems to human body. This paper presents a new algorithm for the analysis of the rail potential and the stray current in DC railway power system operated under independent/parallel power feeding mode. The effect of load current fluctuation during train operation is also calculated by using TPS(Train Performance Simulation) program to analysis the variation of the railway potential and stray current along railway track. Simulation program is developed based on the proposed algorithm and case studies are provided.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.2
• /
• pp.128-136
• /
• 2003

This paper investigates the application of the anti-windup scheme to control U voltage of the three-phase four-wire active power filter, installed in a three-phase four-wire power system. In order to reduce efficiently the harmonic currents caused by the switching loads and to improve the whole performance of the flower system, the DC voltage of the three-phase four-wire active power filter should be properly controlled. PI controller can be applied to the U voltage controller of the three-phase four-wire active power filter. However, a large error input to PI controller leads to a windup phenomenon which deteriorate the dynamic characteristics of the U voltage controller Therefore, the application of the anti-windup scheme for the DC voltage controller is proposed and the improved performances of the anti-windup U voltage controller are proved through the computer simulation study.

• The Journal of the Korea Contents Association
• /
• v.11 no.10
• /
• pp.286-292
• /
• 2011

This study investigated the degree of fracture healing using cathode stimulation of microcurrent, cathode and anode stimulation of High Voltage Pulsed Galvanic Current (HVPGC). Measures were performed by X-ray test and Hematoxylin-Eosin stain and Masson's trichrome stain and osteocalcin-positive immunoreactivity. In the measure of X-ray, microcurrent stimulation group revealed more rapid recovery than the groups of HVPGC's cathode and anode stimulation in bone union degrees. Microcurrent group showed significant difference statistically (p<0.05). However, the groups of HVPGC's cathode and anode stimulation didn't show significant difference statistically(p>0.05). In the histologic examination with Hematoxylin-Eosin and Masson's trichrome, microcurrent stimulation group was observed more proliferation of irregular woven bones than the groups of HVPGC's cathode and anode stimulation. Osteocalcin-positive immunoreactivity was observed more osteoblast, osteocyte, osteoclast, bone matrix than the groups of HVPGC's cathode and anode stimulation. Microcurrent stimulation can be considered an effective way during healing of fresh fracture and it can show more effective method than HVPGC's cathode and anode stimulation in the fracture healing.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.5
• /
• pp.457-465
• /
• 2011

The fault analysis and detecting algorithm for a 3 phase diode rectifier is proposed. The 3 phase dioderectifier is used for the AC power rectifier of the PWM inverter. The input power or diode faults cause theripples of the DC voltage, degradation of the control performance and life shortening of the DC link capacitor.In this paper, the ripple of the DC voltage is mathematically analyzed for the earth fault of input power andopen circuit fault of the diode, respectively. The fault detection and type of fault can be obtained by comparingthe average DC voltage and the instant DC voltage which is sampled with 6 times of grid frequency. Theproposed method can be easily applicable and doesn't require additional circuit. The experimental and simulationresults are presented to verify the validity of the proposed method.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.2
• /
• pp.131-136
• /
• 2021

A DC motor is an important driving source used in a wide range along with an induction motor. Although the structure is complex and has disadvantages in terms of maintenance, most of the demands are given to induction motors as a power source in the industry today, but due to its excellent control performance, DC motors are constantly being used as small-sized control motors. In addition, DC motors with a structure capable of high-power and high-efficiency operation are being developed with the development of magnetic materials as a structure capable of using a permanent magnet in a armature. In addition, the configuration of the controller is simpler than that of an induction motor using an inverter, and the demand for a DC motor is still not negligible, so it is still occupied as an important power source. Considering these trends, this paper attempts to investigate the control performance of DC motors through hardware implementation such as modeling through simulation, PWM generation circuit and electric motor circuit using EPLD, and PI control using processor.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.6
• /
• pp.802-808
• /
• 2019

DC motors are used extensively on shipboard, including as the ship's winch operating motor, owing to their simple speed control and excellent output torque characteristics. Moreover, they were used as propulsion motors in the early days of electric propulsion ships. However, mechanical rectifiers, such as brushes, used in DC motors have certain disadvantages. Hence, brushless DC (BLDC) motors are increasingly being used instead. While the electrical characteristics of both types of motors are similar, BLDC motors employ electronic rectifying devices, which use semiconductor elements, instead of mechanical rectifying devices. The inverter system for driving conventional BLDC motors uses a two-phase excitation method so that the waveform of the back electromotive force becomes trapezoidal. This causes harmonics and torque ripple in the phase current switching period in which the winding wire through which the current flows is changed. Researchers have studied and presented various methods to reduce the harmonics and torque ripple. This study applies a cascaded H-bridge multilevel inverter, which implements a proportional-integral speed current controller algorithm in the driving circuit of the BLDC motor for electric propulsion ships using a power analysis program. The simulation results of the modeled BLDC motor show that the driving method of the proposed BLDC motor improves the voltage waveform of the input side of the motor and remarkably reduces the harmonics and torque ripple compared with the conventional driving method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.528-535
• /
• 2020

Recently, the protection coordination method of DC systems has been presented because renewable energy and distributed resources are being installed and operated in distribution systems. On the other hand, it is difficult to detect ground faults because there is no significant difference compared to a steady-state current in ungrounded IT systems, such as DC load networks and urban railways. Therefore, this paper formulates the detection principle of IMD (Insulation Monitoring Device) to use it as a protection coordination device in a DC system. Based on the signal injection method of IMD, which is analyzed by a wavelet transform, this paper presents an algorithm of detecting ground faults in a DC system in a fast and accurate manner. In addition, this paper modeled an IMD and an ungrounded DC system using the PSCAD/EMTDC S/W and performed numerical analysis of a wavelet transform with the Matlab S/W. The simulation results of a ground fault case in an ungrounded DC system showed that the proposed algorithm and modeling are useful and practical tools for detecting a ground fault in a DC system.

• Therapeutic Science for Rehabilitation
• /
• v.8 no.4
• /
• pp.7-18
• /
• 2019

Objective : This systematic review aimed to investigate the impact of transcranial direct current stimulation combined with constraint-induced movement therapy (CIMT) in patients with stroke Methods : PubMed and NDSL databases were employed to review literature published between January 2009 and December 2018. The main search terms were "Transcranial direct current stimulation" or "tDCS," "Constraint-induced movement therapy" or "CIMT," "Upper extremity function," "Upper limb," and "Stroke." Based on the inclusion and exclusion criteria, 6 articles were selected. Furthermore, intervention effects on upper extremity function, activities of daily living, and cortical activity were assessed. Results : The current intensity, application time, and protocol of the CIMT varied the between studies. However, the intervention procedures to perform CIMT immediately after transcranial direct current stimulation was the same. Transcranial direct current stimulation combined with CIMT was effective in improving upper limb function and activities of daily living in patients with stoke and had a significant effect on cerebral cortex activation. Conclusions : This study provides information on transcranial direct current stimulation combined with CIMT for use by clinical therapists. Further studies are needed to standardize the stimulation time, current intensity, and electrode attachment position. Furthermore, randomized controlled trials, including long-term follow up, are needed for larger populations using the most appropriate CIMT protocol.