• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.350-351
• /
• 2011

본 논문에서는 대형 LED lamp용 직렬 공진형 direct ac-dc 컨버터를 제안하였다. 교류상용전원을 통한 LED lamp에 전원 공급 시, 입력전류의 왜곡을 방지하기 위해, PFC ac-dc 컨버터가 적용된다. 하지만 PFC 컨버터의 특성에 따라 회로의 복잡도 및 수용 전력의 한계가 존재한다. 제안된 컨버터는 기존의 전력변환 방식과 다른 형태로서, 교류 쵸퍼(AC chopper)와 직렬공진회로가 혼합된 구성을 가지며, 교류 쵸퍼의 직접 전력 변환을 통해 PFC 회로 구성없이도 고 역률을 획득할 수 있으며, 직렬공진회로를 통하여 제안된 컨버터의 모든 스위치의 영전압 스위칭(ZVS) 턴-온동작을 통해 손실저감을 도모한다. 본 논문에서는 제안된 컨버터의 동작원리를 간단히 설명하고, 250W의 프로토 타입을 통하여 제안된 컨버터의 우수성을 검증한다.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.145-146
• /
• 2019

본 논문에서는 DQ 변환을 적용한 직렬-직렬 공진형 무선 전력 전송 시스템의 동기 좌표계 모델을 제안한다. 일반적으로 무선 전력 전송 시스템의 경우 급전 측과 집전 측에 단상 전류가 흐르기 때문에 제어에 어려움이 있다. 따라서 정상 상태의 전압 및 전류의 수식을 이용하여 부하에 전달되는 전압 및 전류의 크기를 제어하는 경우가 많다. 따라서 과도 상태의 전압 및 전류의 동특성이 원하는 특성과 다르게 나타날 수 있다. 본 논문에서는 직렬-직렬 공진형 무선 전력 전송 시스템의 단상 전압 및 전류를 DQ 변환하여 과도 상태 및 정상 상태의 전압 및 전류의 동특성을 해석할 수 있는 등가 회로 모델을 제시한다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.5
• /
• pp.259-267
• /
• 2010

An experiment has been performed in order to investigate the characteristics of multiple thermoelectric modules (TEMs) with electrical circuits. The open circuit voltage of TEM connected parallel circuit is equal to the sum of individual TEMs. In contrast, the open circuit voltage is equal to the average of that individual TEM for a series circuit. The power output and conversion efficiency of TEM for both parallel and series circuits increase as the operating temperature conditions for individual TEMs becomes identical. Comparing parallel with series circuits, the power generation performance is more excellent for series circuit than parallel circuit. This result is attributed to the power loss from the TEM with better power generation performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.63-70
• /
• 2004

This paper describes the link layer and physical layer of the Serial ATA which is the next generation for parallel ATA specification that defines data transfer between PC and peripheral storage devices. The link layer consists of CRC generation/error detection, 8b/10b decoding/encoding, primitive generation/detection block. For the physical layer, it includes CDR(Cock Data Recovery), transmission PLL, serializer/de-serializer. It also includes generation and receipt of OOB(Out-Of-Band) signal, impedance calibration, squelch circuit and comma detection/generation. Additionally, this chip includes TCB(Test Control Block) and BIST(Built-In Selt Test) block to ease debugging and verification. It is fabricated with 0.18${\mu}{\textrm}{m}$ standard CMOS cell library. All the function of the link layer operate properly. For the physical layer, all the blocks operate properly but the data transfer is limited to the 1.28Gbps. This is doe to the affection or parasitic elements and is verified with SPICE simulation.

• Journal of the Korean Society for Railway
• /
• v.11 no.5
• /
• pp.477-481
• /
• 2008

This paper dealt with a detection method of series arc existence which is a symptom of electric fires in low-voltage system. The proposed detection circuit consists of a high-pass filter with a low cut-off frequency of 3kHz to attenuate power frequency voltage by 80 dB and an active band-pass filter with a center frequency of 4kHz to detect only the series arc signals. The performance of the circuit was evaluated in a phase-controlled incandescent lamp as a non-linear load and an inverted-fed induction motor as a high frequency load by using the arc generator specified in UL1699. From the experimental results, it was confirmed that the proposed method solved the detection error, which is being the most problem, by discriminating the series arc signal even in non-linear and high frequency loads.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.34-35
• /
• 2009

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.250-253
• /
• 2007

This paper presents a new sustain driver employing energy recovery function to minimize power losses transpired during the operation of plasma display panel. The proposed circuit uses the resonance between the equivalent capacitance of panel and an external inductor to provide/recover energy to/from the panel. The proposed circuit can save the system cost compared with the conventional one, and has high-performance in energy recovery. To verify the validity of the proposed circuit, we implemented experiments based on 7.5 inch AC-PDP.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.6 no.4
• /
• pp.1-7
• /
• 1969

A Series Inverter circuit is analyzed and Fourier analysis is applied to its output waveform. It is proved that under the optimum condition the Output is nearly sinusoidal wave which contains only odd harmonic Components and the relative amplitude of the hramonic components are expressed with very simple formula which contain only "Q" of the circuit as a parameter.parameter.

• Journal of KIISE:Software and Applications
• /
• v.26 no.4
• /
• pp.500-507
• /
• 1999

다중 데이터베이스 시스템에서 지역 사이트의 자치성을 유지하면서 전통적인 전역 직렬가능성을 보장하는 일은 지역 트랜잭션에 의한 간접 충돌로 인하여 전역 트랜잭션의 동시 실행 정도의 저하를 초래하게 된다. 본 논문에서는 동시성 정도를 향상시킬수 있도록 전역 직렬가능성 기준을 완화하고 이를 기초로하는 전역 동시성 알고리즘을 제안한다. 제안된 알고리즘은 트랜잭션의 연산 유형을 이용하고 있으므로 특히 읽지 전용 트랜잭션의 경우 동시성 정도의 향상을 기대할 수 있다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.6
• /
• pp.251-255
• /
• 2015

In this paper, we propose a fuse controller which is used for storing the optimal value or the correction value for the surrounding product of the IoT applications and it is implemented serial communication circuit using a single pin. Because of the proposed single pin protocol is simpler in the hardware than the conventional $I^2C$ and SPI using two or more pins, it is suitable for the area of small amount of data transmission. The function of the one pin protocol is verified by logic simulation and the FPGA test board and it is fabricated using CMOS 0.35um technology. It is expected to use the IoT product that require the low power consumption and simple hardware.