It is very important for hemodialysis in patients with end stage renal disease to obtain vascular access that resists repeated punctures and maintains adequate blood flow. This study was designed to indentify factors that may influence early patency rate of autogenous arteriovenous fistula. Material and Method: 49 cases in 47 patients who underwent radiocephalic fistula formation in our hospital from June 2002 through May 2003 were reviewed and analyzed. Result: The early patency rate was 79.6%. Age, sex, hypertension, and diabetes mellitus were not significant factors for patency. Body mass index and duration of hypertension and diabetes did not influence the early results either. Cephalic vein diameter measured preoperatively and blood flow at radio-cephalic fistula were significantly positive correlative factors. Groups with the vein diameter less than 2.7mm, or with the blood flow less than 100 mL/min had significantly lower early patency rate than the other groups. Conclusion: To improve early patency rate of radiocephalic fistula, large sized cephalic vein should be selected and if the intraoperative flow at radiocephalic fistula is less than 100 mL/min, another arteriovenous fistula formation should be considered.
Kim, H.W.;Ju, Y.C.;Lee, D.H.;Lee, K.S.;Kim, K.H.;Kim, E.I.
Proceedings of the KIEE Conference
/
2001.04a
/
pp.480-484
/
2001
본 연구에서는 실제 풍력 자원 측정용 Pole에 설치된 풍속계가 mast에 의한 후류와 풍속계 설치시 기울어짐에 의해 풍속 data가 어떠한 영향을 받는가에 대하여 고찰하였다. 먼저 mast은 직경 4", 6" Pipe에 대하여 각각 실험하였고, 측정 mast의 방위각은 풍속에 평행한 방향을 $0^{\circ}$ 로 정하고 측정 mast 중심으로부터 $0^{\circ}{\sim}20^{\circ}$ 까지 $5^{\circ}$ 간격으로 측정하였다. 이 연구를 통해 실제 일정 두께를 갖는 mast에 설치되어 있는 풍속계에서의 풍속이 풍향에 대한 boom의 위치와 기울어짐에 따라 영향이 있음을 확인할 수 있었고, mast의 직경에 대한 영향도 크게 있음을 확인할 수 있었다. 따라서, 본 연구의 결과를 이용하여 향후의 풍력자원 자료 측정설비의 설치상의 정확도 검증이나 혹은 측정된 자료의 보정등에도 광범위하게 이용될 수 있을 것이다.
본 논문에서는 1.58 ${\times}$ 0.82 ${\times}$ 0.94 $mm^3$크기의 H 형태의 솔레노이드형 RF 칩 인덕터를 코일의 직경과 권선수를 변화시키면서 제작하였고, 그들의 고주파 성능을 비교 분석하였다. 저손실 $Al_2O_3$재료를 코아로 $30{\mu}m{\sim}40{\mu}m$의 여러 직경을 가진 Cu를 코일로 사용하였다. 인덕터의 인덕턴스(L), 품질계수(Q), 저항(R), 임피던스(Z) 그리고 커패시턴스(C) 등의 주파수 특성은 HP4291B로 측정하였다. 실험결과 동일권선수에 대해 코일직경이 자을수록 L, Q, R, 그리고 Z등이 증가하였고, 그 증가폭은 권선수가 클수록 커지는 경향이 있음을 알 수 있었다. 그러나 코일직경이 작을수록 기생 커패시턴스 효과가 빨리 나타나 자기 공진주파수 효과가 감소하는 경향을 보이고 있음을 확인하였다. 코일직경이 $3{\mu}m$이고 권선수가 6인 경우에 대표적인 값들은 다음과 같다. L=31.4nH(at 250MHz), Q=49.6(at 700MHz), R=0.362${\Omega}$(at 1MHz)
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2000.04a
/
pp.24-24
/
2000
작업 중 공구를 관에 떨어뜨리거나 작업하기 위해 관을 이동하던 중 다른 물체에 부딪힐 경우 복합재로 만들어진 관이 손상을 입게 되는 경우가 생기는데 관이 상황에 따라 얼마나 손상을 입었는지가 본 연구의 관심이다. 충격자는 직경이 25.4mm와 12.7mm인 반구형 2종류와 모서리의 직경이 15mm인 원추형 1종류로 각각 무게가 다르며, 떨어뜨리는 자유낙하 높이는 120mm에서 700mm로 종류에 따라 간격을 달리했다. 실험 장치로는 Dynatup 8250을 사용했으며 충격에너지, 최대충격하중, 충격변위, contact diameter를 측정했다. 시험 후 시편은 방사선 촬영을 하여 충격자의 종류에 따라 손상의 정도가 어떻게 다른지를 파악했다. 직경이 25.4mm인 반구형의 충격자는 표면의 손상은 적었으나 복합재 관의 내부에 delamination이 많이 생겼으며 직경이 12.7mm인 반구형의 충격자는 표면의 손상이 심했으나 내부의 delamination이 상대적으로 적었다. Contact diameter와 최대충격하중과의 관계는 실험치와 이론치가 잘 일치했으나 Kinetic energy와 최대충격하중과의 관계는 실험치와 이론치의 차이가 있었다.
Proceedings of the Korea Water Resources Association Conference
/
2008.05a
/
pp.1833-1838
/
2008
본 연구는 호안보호공 중 하천 바닥 또는 제방의 유지시설로 많이 쓰이는 사석의 안정성 분석을 위하여 수리실험을 실시하였다. 안정성 분석을 위해 Isbash식, Netherlands 간이공식, ASCE식, Pilarczk식, Maynord식을 검토하였다. 실험결과 사석의 직경이 커짐에 따라 한계유속이 증가하였고, 형상계수가 커지면 한계유속이 증하하였다. 또한 랜덤배열일 때보다 규칙배열일 경우 한계유속이 크게 측정 되었다. 이로서 형상계수와 인터로킹의 정도가 사석의 안정성에 중요한 함수라는 것을 나타낸다. 사석은 Maynord의 직경공식과 미 California주 정부 중량공식이 적합하게 나왔고, 모형사석의 규칙배열에서는 Pilarczk의 직경공식과 Netherlands 간이 무게공식이 적합하였다. 모형사석의 랜덤배열시에는 Isbash 공식이 적합하였다. Isbash 공식과 직경산정에 형상계수를 대입하여 새로운 식을 개발하였다. 이는 기존공식의 적용성을 더 개선할 수 있으리라고 기대된다.
Journal of the Korean Society of Propulsion Engineers
/
v.14
no.5
/
pp.51-56
/
2010
An experimental study was performed to understand spray characteristics of the V type rotating fuel nozzle with orifice diameters by using high speed rotational system. The experimental apparatus consist of a high speed rotational system, fuel injection system and acrylic case. The droplet size and velocity were measured by PDPA(Phase Doppler Particle Analyzer) and spray was visualized by using Nd-Yag laser-based flash photography. From the test results, droplet size is reduced with increasing orifice diameter up to the critical value. When increasing orifice diameter over than this critical value, droplet size is not decreased with increasing the orifice diameter. This is due to the irregular distribution of the liquid sheet around the inner surface of injection orifice.
Proceedings of the Korean Vacuum Society Conference
/
2010.02a
/
pp.75-75
/
2010
단일벽 탄소나노튜브(SWNT)는 뛰어난 물리적 성질과 화학적 안정성을 가지고 있어서 다양한 분야의 응용이 기대되어 폭넓은 연구가 진행 되고 있다. 특히 SWNT의 전기적 및 기계적 특성들은 SWNT의 직경 및 뒤틀림도(chirality)에 의해 크게 좌우되기 때문에, 합성하는 단계에서 직경 또는 chirality를 제어에 관한 많은 이론적 연구가 진행되어 왔으며, 최근에는 초기 SWNT의 핵생성 단계에서의 촉매의 거동 및 상호 연관성 등에 관한 실험적인 연구결과들이 속속 보고되고 있는 실정이다. 하지만, 아직도 이에 관한 더욱 다양하고 활발한 연구 접근 및 결과들이 필요한 시점이다. 상기 배경을 바탕으로 본 연구에서는 균일한 직경을 갖는 SWNT의 합성을 위한 기초연구로서 SWNT의 직경과 촉매나노입자의 크기의 상호 연관성에 대해 체계적으로 조사하였다. 우선 SWNT합성을 위한 촉매나노입자를 얻기 위해 페리틴(ferritin)용액의 농도 및 스핀코팅 조건을 변화시킴으로써 기판 위에 분산농도를 제어한 후, 대기 열처리를 통하여 촉매나노입자의 농도를 제어하였다. 나노입자의 평균직경은 4 nm 정도로 비교적 균일하였으며, 고농도의 촉매입자는 SWNT의 다발화(bundling)를 유발하였다. 따라서, SWNT와 나노입자 직경의 상호연관성을 조사하기 위해서는 단분산(monodispersed) 된 나노입자를 이용하였으며, 아르곤 분위기에서 추가적으로 고온($900^{\circ}C$) 열처리를 실시함으로써 나노입자의 크기감소를 도모하였다. 실험결과, 열처리 시간의 증가에 따라 입자크기가 감소함을 확인하였으며, 이는 나노입자의 증발에 의한 것으로 예상된다. 다음으로는 열처리를 통하여 직경이 제어된 나노입자를 이용하여 SWNT를 합성한 후 SWNT와 촉매크기 사이의 크기 관계를 조사하였다. SWNT의 합성은 메탄을 원료가스로 열화학증기증착법을 이용하였고, 합성기판으로는 산화실리콘웨이퍼와 퀄츠기판을 이용하였다. 성장한 SWNT의 직경은 AFM을 이용하여 측정하였으며, 퀄츠기판에 수평배향 성장시킨 SWNT를 3차원 구조의 기판으로 전사(transfer)하여, 라만분석이 용이하도록 하였다.
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.31
no.4
/
pp.82-91
/
2003
Experiments to investigate the mixing performance of unlike doublet impinging jets are conducted. Reynolds number of simulants used in this study rages from 1.0 to 1.5 Cold flow test is performed to investigate the hydrodynamic effect and spray of the impinging jets are collected locally and calculated by using Rupe's mixing efficiency equation. Momentum exchanges and relative velocity ratio between two jets are taken as the main parameter to represent the effect of enlargement of the orifice diameter. As diameter ratio increases, the corresponding momentum ratio where maximum mixing efficiency occurs and relative velocity at the maximum mixing efficiency ranges 0.6 to 0.7, respectively. Penetration depth can be taken as a prominent parameter to estimate the mixing efficiency.
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.46
no.1
/
pp.59-67
/
2018
In this paper, the test facility for coaxial propellers at low Reynolds developed and validated by measured data. The test equipment was designed to measure the hovering performance of propellers according to distances between the upper/lower propellers. Thrust, torque, rotational speed, vibration, and amperage of upper and lower propellers can be measured separately. The data acquisition system was built to collect signals of sensors, and LabVIEW software was used to control the motor and collect the signal. The hover performance tests of single propellers were preceded for the facility validation, and then the performance values of coaxial propellers were measured according to distances and diameter differences between the upper/lower propellers. The results showed that the high efficiency is achieved at 20%~30% distance between the upper propeller and lower one. The configuration that the upper propeller has shorter diameter than the lower one has the highest efficiency than other configuration.
Purpose: We wanted to evaluate the normal glenoid size of Koreans in their 7th and 8th decades by conducting Computed tomographic (CT) studies. Materials and Methods: The CT images were obtained from the normal scapulae of the patients (mean age: 68.8) who had humeral fracture. A display workstation version 2.0.73.315 was used to measure the scans to determine the maximal superoinferior (SI) and anteroposterior (AP) diameters of the glenoid vault. Results: The average diameters of curvature of the glenoid were 31.2 mm (range: 27 to 34 mm) in the superior-inferior direction and 26.1mm (range: 22 to 31mm) in the anterior-posterior direction. Conclusion: This study showed the normal glenoid size of Koreans and it is different from the size that the international literature reported. It should be an important factor for the treatment of fracture or in designing arthroplasty implants.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.