• Journal of the Korean Institute of Landscape Architecture
• /
• v.49 no.5
• /
• pp.59-70
• /
• 2021

This study was to investigate the measurement point of root collar diameter of landscape trees in Korea. It may contribute to avoiding disputes caused by the difference in measurement criteria of root collar diameter of landscape trees between tree growers and constructors. The difference between landscape trees' root collar diameter measurement point was 3.59cm from 6cm underground to the surface and 1.35cm from 0cm to 6cm above ground. The source root collar diameter measurement point difference was larger in the basement than in the ground. The standard deviation of the root collar diameter of the landscape tree was 0.64 from 6cm underground to the surface, and the difference in standard deviation from 0cm to 6cm above ground was 0.16. The difference by measurement point of the root collar diameter was larger in the basement than in the ground. It has been proposed to set the reasonable measurement point of the landscaping tree root collar diameter at the inflection point where the standard deviation of the tree trunk diameter is the smallest in line with the size change of the standard for each root collar diameter measurement point. By tree species, Cornus officinalis Siebold & Zucc. 18cm above the ground, Chionanthus retusus Lindl. & Paxton. 12cm above the ground, Zelkova serrata (Thunb.) Makino. 12cm above the ground, Celtis sinensis Pers. 12cm above the ground, Styrax japonicus Siebold & Zucc. 10 cm above the ground, Cornus officinalis Siebold & Zucc. 10cm above the ground, Acer palmatum Thunb. ex Murray. 6cm above the ground, Ilex rotunda Thunb. 6cm above the ground, Quercus myrsmaefolia Blume. 4cm above the ground, Lagerstroemia indica L. 2cm above the ground The above heights were shown as reasonable measurement points. The difference by landscape tree root collar diameter measurement site showed that the standard deviation was small throughout the tree species, and the reasonable average measurement point with a stable slope of the deviation was 12cm or more on average. It can be said that the reasonable measurement point of the root collar diameter of a landscape tree is set at an average of 12cm above the ground. However, recognizing 30cm, which is a familiar ruler(尺) in traditional practices, is quick, It was recommended to measure at the height of 30cm from the surface for a reasonable measurement point of the root collar diameter of a landscape tree, for the uniformity of measurement standards.

• The Journal of the Korea Contents Association
• /
• v.15 no.6
• /
• pp.276-282
• /
• 2015

Fetal cerebellum is grow depending on the gestational age, measurement of transverse cerebellar diameter(TCD) is being used import indicator of fetal growth prediction in clinical. In this study, the subjects were normal pregnant women 20~37 week of gestation, and the volume scan was conducted on the 340 subjects. The research reports was indicated by regression curve the growth of fetal TCD in accordance with the gestational age. It got to the value of the results from a linear regression equation. Measurement fetal TCD using 3D US was statistically significant(p<0.001) and useful in the prediction of gestational age. TCD increases with gestational age can also distinguish between the normal fetal and prediction of accurate gestational age of fetal growth retardation. If the basic data of the present study, ongoing research is performed, the TCD using by 3D US are expected to be usefully applied in the correct prediction gestational age.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.515-520
• /
• 1998

영상처리방법에 의한 핵연료봉의 제원을 측정하기 위하여 영상처리 소프트웨어를 개발하였으며, 이 영상처리방법에 의하여 핵연료봉의 직경에 대한 백분을 측정상대오차는 $\pm$2.09% 이내이며 영상처리방법이 아닌 기존 방법에 의한 백분율 측정상대오차 $\pm$9.70 %보다 측정정확도가 약 5배정도 향상되었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.1
• /
• pp.9-13
• /
• 2002

A pool image processing measurement method has been developed to improve the examination efficiency and to minimize the errors of dimensional measurements of spent fuel assemblies in pool. Diameter and length measurements of mock-up fuel rods using the image processing system are $-0.24{\pm}0.03mm,\;0.34{\pm}0.06mm$ on the basis of the true value and their maximum errors are within -0.3 and 0.4mm, respectively, According to the result of dimensional measurement of spent fuels in pool, the upper and lower part diameter and mid part diameter of fuel rods of the J44 fuel assembly irradiated for 2 cycles in the Kori-2 nuclear reactor were decreased by about 2.0 and 3.0% in comparison with design values, respectively. The length of fuel rods was elongated by about 0.4%. The change behavior of diameter and length. of fuel rods of the F02 fuel assembly irradiated for 3 cycles in the Kori-1 nuclear reactor showed a trend similar to the results of J44.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.64-64
• /
• 2012

아라미드는 일반적인 유기섬유와는 다른 우수한 역학적 성질을 바탕으로 보호의류 중에서 방탄방호 및 방검보호 의류에 사용되는 고부가 소재이다. 현재까지 ATY기계에서 사의 구조와 물성에 큰 영향을 미치는 Nozzle의 구조에 대한 연구결과는 많이 발표되어왔다. 그러나 최근 들어 소방방화방 검용 보호의류에 많이 사용되는 아라미드사에 ATY 공정 중에서 Nozzle의 직경이 ATY사의 물성에 어떤 영향을 미치는가에 대한 연구는 발표된 바가 없다. 따라서 본 연구에서는 Para-aramid/Nylon hybrid사를 이용하여 ATY로 제조할 경우, 표면에 생기는 loop로 인하여 타 소재와 접착시, 접착제 담지 성능이 향상되어 접착력이 상승되는 반면 아라미드 Hybrid사의 역학물성은 ATY가 가공되기 전의 물성보다 저하되는 약점을 가지고 있다. 따라서 본 연구에서는 ATY 제조공정에서 Nozzle의 직경을 달리할 때 Aramid/Nylon Hybrid ATY사의 물성변화를 분석함으로서 방화복과 방검용 보호의류에 적합한 아라미드 ATY사를 개발하고자 한다. 본 연구에서는 ATY 제조공정 중 다른 공정조건은 동일하게 하고 Nozzle의 직경을 0.6, 0.75, 1, 1.2mm로 변경하여 4가지 시료를 준비하고 물성분석을 위하여 제조된 시료의 강신도, 초기탄성률을 각각 측정하여 인장특성을 확인하였으며, 건열수축률과 습열수축률을 측정하여 시료의 열 수축률을 측정 분석하였다. 표면의 루프 발현 정도를 보기위하여 형태 불안정성을 측정 평가하였으며 영상현미경시스템을 사용하여 표면특성을 측정 평가하여 다음과 같은 결론을 얻었다. Nozzle의 직경이 증가함에 따라 절단강도는 30% 감소하였고 초기탄성률은 3배 가까이 감소하였다. 그리고 절단신도는 2배정도 증가하는 경향을 나타내었다. 또한 Nozzle의 직경이 증가함에 따라 ATY hybrid사의 건 습열수축률이 증가하다가 직경이 1.2mm일 때 감소하는 경향을 나타내었고 직경 변화에 따라 4~6%의 열 수축률의 분포를 보였다. Para-aramid/Nylon hybrid사의 형태불안정성은 0.3~0.5%를 분포를 나타내었고 Nozzle의 직경이 0.6, 1mm일 때 상대적으로 낮은 ATY의 불안정성이 확인되었다. Nozzle의 직경이 감소할수록 loop의 엉킴이 적으며 flat하였으며 직경이 1.2mm일 때 가장 조밀하고 표면에 loop가 많이 형성된 것을 확인하였다.

• Journal of Sensor Science and Technology
• /
• v.8 no.4
• /
• pp.347-353
• /
• 1999

We constructed an interferometer for precise measurement of the ball diameter, and measured the diameter of steel ball with a diameter of 78 mm. The interferometer was consisted of etalon to instal ball between two parallel plates and placed on the monolithic flexure to be moved parallel. The ball diameter was calculated from phase difference of one pair of signals interfered between the both sides of ball and two parallel plates, and the signals was observed by photodetectors with scanning the etalon. The results showed that the diameter of steel ball was 78.1893544 mm and measurement uncertainty of 29 nm in confidence level of 95.5%.

• Journal of Korean Ophthalmic Optics Society
• /
• v.17 no.4
• /
• pp.469-476
• /
• 2012

Purpose: The purpose of this study is to investigate the changes of asphericity according to diameter and direction of the cornea. Methods: The changes of asphericity according to diameter and direction of cornea is measured by using Pentacam(Oculus Co., Germany), as targeting 57 adults (average $27.0{\pm}4.8$, 20 men, 37 women) without any ophthalmic diseases, which may be effective in eyesight, and refractive surgery. Results: As diameter increases in every direction based on the corneal vertex, asphericity has attentively increased (p<0.05), and the size of asphericity in each direction from every measured diameter showed as superior > nasal > inferior > temporal. In group comparison by nearsightness and astigmatism level, asphericity measured high when nearsightness and astigmatism levels were higher, and this appears to be statistically attentive.(p<0.05). Conclusions: Asphericity of cornea significantly increased according to increase of diameter of cornea, and as measured figure or increased quantity appeared differently in all directions based on corneal vertex, so it helps to understand shape of cornea, and considered that is the part to be considered during manufacturing and fitting of RGP lenses.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.49 no.2
• /
• pp.27-40
• /
• 2021

This study was carried out for the description of the conflicts on the measurement of the root collar diameter of the landscape trees that are currently being produced, distributed, and planted in S. Korea, and for determination of the standard for root collar diameter measurement. The difference in consciousness of appropriate measurement of root collar diameter among different ages of landscape practitioners was statistically significant at p<0.05 level. It seemed to be due to the difference in the amount of field experiences among different age groups. On "the ambiguity of measuring the root collar diameter' of landscape trees", the consciousness was significantly different at p<0.05 level among job positions. On "Improvement of measurement criteria for landscape trees," it was significantly different at p<0.05 level among job types. This was thought to be due to the disagreement between the client and the contractor. On "prevention of topsoil removal" when excavating landscape trees, the consciousness was significantly different at p<0.001 level among different age groups, and different at p<0.01 level among different occupations, and different at p<0.05 level among different working area. The consciousness on "removing top soil when excavating landscape trees and rooting after transplantation" was not significantly different. The consciousness on the conflict caused by "ambiguity in root collar diameter measurement criteria" was high with an average of 3.85 for job type, occupation, jop position, and work experience. It was higher for landscape contractors than public institutions. The higher job positions and more experiences, the more conflicts. The consciousness on the appropriate position of root collar diameter measurement for landscape trees revealed that measuring at above-ground part (66.5%) was prefered to the underground part (33.0%). During the excavation of landscape trees for transplant, topsoil removal up to average depth of -2cm to -4cm was favored by 84.0%, and the purpose of removing topsoil was recognized as 'to increase the size and unit cost' by 59.7%.

• Proceedings of the Korea Contents Association Conference
• /
• 2015.05a
• /
• pp.195-196
• /
• 2015

태아의 소뇌는 임신주수에 따라 성장하며 소뇌횡직경 길이의 측정은 태아성장 예측의 중요한 지표로 활용하고 있다. 임신주수에 따른 태아 소뇌횡직경의 성장을 회귀곡선으로 표시하였고 선형회귀방정식에서 결정계수를 얻었다. 3차원초음파를 이용한 소뇌횡직경의 측정법은 통계적으로 유의(P<0.001)하였으며, 태령을 예측함에 유용하다는 것을 알 수 있었다. 또한 성장장애가 있는 태아의 경우에도 임신주수의 예측이 가능하다. 본 연구를 기초자료로 하여 지속적인 연구가 시행된다면 정확한 임신주수 예측에 유용할 것으로 기대한다.

• Korean Journal of Agricultural Science
• /
• v.6 no.2
• /
• pp.192-197
• /
• 1979

Spread factors were tried to determine the diameter of airborne droplet emitted: from the sprayer by the measurements of airborne droplet diameter emitted from the uniform size droplet producer and impression diameter on Kromekote card or Eucalypt's leaf in the different dilute concentration with Geigy Red Herbicide Dye from 0.5% to 2% by weight. The results abtained were as follows; The general form of the equation in the relationship between airborne droplet and impression diameter on Kromekote card or Eucalypt's leaf was an exponential equation as follows; $$Y=aX^b$$ which gave a linear relation on log-log graph paper. The spread factor seemed to be larger in the thin dilute concentration than in the thick dilute concentration. The spread factor was remarkably smaller on Eucalypt's leaf than on Kromekote card due to the penetration of liquid into the leaf and the stomata of the epidermis. The calculated equation of the mean depth of the droplet sprayed on Eucalypt's leaf was the same form as $Y=aX^b$, which implied that the spray liquid was distributed in surplus in accordance with the diameter of the droplet larger than the optimum size droplet to control insect and disease.