• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12A
• /
• pp.1883-1890
• /
• 1999

Wireless communication in an urban area, the accurate prediction of wave propagation characteristics are very important to determine communication service areas, select optimal base-stations, and design cells, etc. The CCIR model is a propagation prediction model using a shadowing by the buildings in an urban area. This model represent the shadowing rate by the means of the effect of shadowing between base-station and mobile unit in a shaped linear plane. But, This one occurred a lot of prediction error because it did not consider that density area by the buildings and terrain configurations by the hill and mountain on Line-Of-Sight. In this thesis, an improved propagation prediction model is proposed to reduce prediction error. We presents a new equation, which is using the SAS. This equation is associated with the shadow height by the buildings that considers the topology and the number of blocks that can affect the building shadow in the Line-Of-Sight. We measure the received electrical field level of base-station that high density area, medium density area, and low density area, and then compare and analysis the result to prediction of CCIR model and proposed model. The result compared with the measurement, the proposed model has the improvement of 9.71dB in a high density area, 9.66dB in a medium density area, and 4.02dB in a low density area better than the CCIR model. The result compared with the measurement, the proposed model has the improvement of 9.71dB in a high density area, 9.66dB in a medium density area, and 4.02dB in a low density area better than the CCIR model.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.6
• /
• pp.349-356
• /
• 2013

The purpose of this study is to review and overcome the limits of the existing design wave model applied to such waters as those located inside bays or near islands where the impact of wind influenced waves are more dominant, due to the nature of topographic isolation, than the influence of direct waves coming from the open sea. Although the existing model for an inside bay design wave is excellent for considering wind factors and very adaptable to topographically complicated areas compared to other models, it is difficult to show the wave diffractions and reflections caused by large scale structures or topographic features in the region. The study examined the various methods capable of taking into account wave diffraction, the angle of wave reflection, and changes in water depth. As a result of applying the modified design wave model to the target situation (inside bay or near island areas), it was found that the reliability of the design wave height around marine structures was improved, compared to the existing models. Therefore, it is fair to predict that the new model could provide more accurate design waves in the design of marine structures.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.4
• /
• pp.13-19
• /
• 2014

To develop a wind farm in a mountainous terrain like Korea, it is generally more advantageous to install wind turbines along a mountain ridge where has relatively better wind resource because that is open in all directions and free from shielding by the surrounding topography. In this study, the SRTM (Shuttle Radar Topography Mission) v4.1 3 arc-second resolution digital elevation database and the geomorphometric characterization software LandSerf v2.3 are used to extract ridge lines for assessing a wind farm siting in mountainous terrain. The effectiveness of wind farm siting along a ridge line is confirmed that the most of wind turbines in the Gangwon, Taegisan, and Maebongsan wind farms in Korea's mountainous terrain are placed along the primary and secondary ridge lines where wind resource is relatively outstanding.

• 전자공학회논문지 IE
• /
• v.43 no.4
• /
• pp.122-127
• /
• 2006

A series of conductive filler were prepared with electroless plating method. Base conductive materials of the filler were nickel and copper. The cores were prepared with Nylon 6 and rayon in different aspect ratio. Also, various complexes were made with ABS resin and conductive filler with different filler feed ratio. The conductivity of the filler was measured with conductivity analyzer and the size distributions of fillers was measured with laser particle size analyzer. Electromagnetic wave shielding efficiency of each complex film was measured with flange circular coaxial transmission line sample holder within the 1MHz$\sim$1GHz bandwidth range. From this study, the conductivity of filers surpass that of other carbon films. It is available that the filler made of fibrous materials can be applied in plastic molding industry of electric appliances as a EMI filler.

• Tunnel and Underground Space
• /
• v.10 no.1
• /
• pp.80-91
• /
• 2000

Open cut mining of limestone is generally considered to be more advantageous than underground mining in recovery, grade control, economics, and safety, but it causes substantial environmental pollutants such as ground vibration, noise, dust. It also changes ground surface and may destroy vegetation. The Halla limestone mine which lies adjacent to Baikdu mountains range is selected for a model study. To reduce environmental hazards, and to conserve original surface and woods, both open cut and underground mining methods must be adopted. In case of sub-level sloping. a unit block of 87m high, 70m wide, and 100∼l20m long is suggested with an estimated overall recovery of 42%. Some suggestions to reduce the environmental hazards are also included. The followings must be considered in determining the degree of fragmentation; the discontinuity conditions in the rock mass and the charge concentration both at the bottom and column of the hole. In addition to adopting a barrier wall for reducing environmental hazards, the probable production from underground mining is also discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.947-952
• /
• 2015

To supplement energy needs and take advantage of renewable energy sources, many wind farms are currently being built in mountainous areas under the supervision of the Korean government. However, operation of these wind farms can cause serious threats to national security due to Doppler modulation from the wind turbines causing interference with military radar operating in the vicinity. Therefore it is necessary to develop methods to analyze the Doppler frequency during the operation of wind turbines and the effect on radar signals. Based on modeling of the mountainous region, blockage analysis, turbine motion and the radar signals, this paper proposes a signal processing method to extract and analyze the Doppler frequency. Simulation results showed the change of Doppler frequency over time caused by the geometry of the mountainous area and the wind turbine.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.3
• /
• pp.553-562
• /
• 2020

S-band, C-band and X-band radars are used for weather observation purposes. Since the Meteorological Administration, the Ministry of Environment, and Republic of Korea Air Force operate radars according to the purpose of observation by departments, the installation site and observation characteristics are different. From a meteorological point of view, blind observational areas in the low level with an elevation of less than 1 km around the mountainous terrain near Jirisan and Taebaeksan. Assuming a small radar installation, we simulated low-level observations. In order to monitor dangerous weather in North Korea, we analyzed the precipitation of North Korea and simulated a large radar network. Finally, a radar network for Korean Peninsula was proposed.

• Journal of the Korean earth science society
• /
• v.38 no.7
• /
• pp.496-510
• /
• 2017

This study presents a new nationwide quantitative precipitation estimation (QPE) based on the hybrid surface rainfall (HSR) technique using the weather radar network of Korea Meteorological Administration (KMA). This new nationwide HSR is characterized by the synthesis of reflectivity at the hybrid surface that is not affected by ground clutter, beam blockage, non-meteorological echoes, and bright band. The nationwide HSR is classified into static (STATIC) and dynamic HSR (DYNAMIC) mosaic depending on employing a quality control process, which is based on the fuzzy logic approach for single-polarization radar and the spatial texture technique for dual-polarization radar. The STATIC and DYNAMIC were evaluated by comparing with official and operational radar rainfall mosaic (MOSAIC) of KMA for 10 rainfall events from May to October 2014. The correlation coefficients within the block region of STATIC, DYNAMIC and MOSAIC are 0.52, 0.78, and 0.69, respectively, and their mean relative errors are 34.08, 30.08, and 40.71%.

• Journal of Korea Water Resources Association
• /
• v.47 no.10
• /
• pp.867-878
• /
• 2014

Due to the nature of weather radar, blank areas occur due to impediments to observation, such as the ground clutter. Radar beam blockages have resulted in the underestimation rainfall amounts. To overcome these limitations, this study developed the Hybrid Scan Reflectivity (HSR) technique and compared the HSR results with existing methods. As a result, the HSR technique was able to estimate rainfalls in areas from which no reflectivity information was observable using existing methods. In case of estimating rainfalls depending on reflectivity scan techniques and beam-blockage/non beam-blockage, the HSR accuracy is superior. Furthermore, rainfall amounts derived from each method was inputted to the HEC-HMS to examine the accuracy of the flood simulations. The accuracy of the results using the HSR technique in contrast to the RAR calculation system and M-P relation was improved by 7% and 10%(based on correlation coefficients), and 18% and 34%(based on Nash-Sutcliffe Efficiency), on average, respectively. Therefore, it is advised that the HSR technique be utilized in the hydrology field to estimate flood discharge more accurately.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.6
• /
• pp.241-249
• /
• 2022

This paper discusses the design of a ground clutter prevention fence for a radar wind profiler (RWP). The design point of the clutter fence is to improve the quality of the received signal by removing the non-weather clutter coming from the side. In this paper, a clutter prevention fence composed of a metallash mesh around the RWP is proposed, and the phase center of the antenna, the length, and height of the down fence, and the height and slop of the top fence through M&S are designed. The designed ground clutter prevention fence and 256 active phase array antennas were used as basic data. The effectiveness of the design was confirmed by a simulation. The side lobe in the ±90° direction was reduced by more than 30dB depending on the presence or absence of the designed ground clutter prevention fence. The fence was manufactured by 3D modeling, and the clutter shielding performance of approximately 20dB or more on the side of the antenna (±90°) was confirmed by applying it to the currently operated RWP.