• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.2
• /
• pp.77-81
• /
• 2010

D&B(Drill & Blast) method in tunnel construction requires accurate and rapid measurement of the ground movement, which is essential for feedback analysis. Case study and adaptability of IT technique for tunnel survey are discussed in this paper. The application of laserscannig and existing light wave instrument method in the field of tunnel construction were reported in several advanced country including Austria and Japan. Survey for the shoulder movements by IT survey method was conducted at a subway construction site and the results were compared to the conventional method. Also, the economic aspects of laserscannig method were analyzed using measured data which were categorized by expenses, frequency, interval and period in the field of construction. Therefore IT survey solution may contribute to execute more economic and safe construction

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.4
• /
• pp.345-356
• /
• 2004

Open-cut method has been widely used to construct underground structures, but it causes several problems such as traffic congestion and public resentment resulting from severe construction noise and ground settlement. In many cases, it is very difficult to build underground structures safely due to the unknown locations of buried facilities such as water pipes, drainage pipes, gas pipes and high-pressure cable conduits etc. Also in open-cut method, moving buried facilities causes additional cost and extension of construction period. Therefore, this paper is to present a case study in which Tubular Roof construction Method (T.R.c.M.), a newly developed construction method for underground structures using slab steel pipes and PC wall trench, is applied for the construction of a subway tunnel in Seoul. As a result, it is found that T.R.c.M. is a construction method by which tunnels can be constructed safely without any effect on the surrounding environment and traffic flow due to the minimized construction vibration and noise.

• Journal of the Society of Disaster Information
• /
• v.3 no.1
• /
• pp.37-53
• /
• 2007

Various difficult problems occur due to insufficient bearing capacity or excessive settlements when constructing roads or large complexes. Accurate predictions on the final settlement and consolidation time can help in choosing the ground improvement method and thus enables to save time and expense of the whole project. Asaoka's method is probably the most frequently used for settlement prediction which are based on Terzaghi's one dimensional consolidation theory. Empirical formulae such as Hyperbolic method and Hoshino's method are also often used. However, it is known that the settlement predicted by these methods do not match with the actual settlements. Furthermore these methods cannot be used at design stage when there is no measured data. To find an elaborate method in predicting settlement in embankments using various test results and actual settlement data from domestic sites, Back-Propagation Neural Network(BPNN) and Recurrent Neural Network(RNN) were employed and the most suitable model structures were obtained. Predicted settlement values by the developed models were compared with the measured values as well as numerical analysis results. Analysis of the results showed that RNN yielded more compatible predictions with actual data than BPNN and predictions using cone penetration resistance were closer to actual data than predictions using SPT results. Also, it was found that the developed method were very competitive with the numerical analysis considering the number of input data, complexity and effort in modelling. It is believed that RNN using cone penetration test results can make a highly efficient tool in predicting settlements if enough field data can be obtained.

• Journal of Korean Society for Geospatial Information Science
• /
• v.13 no.1 s.31
• /
• pp.63-69
• /
• 2005

Interferometric Synthetic Aperture Radar(InSAR) is a rapidly evolving technique. Spectacular results obtained in various fields such as the monitoring of earthquakes, volcanoes, land subsidence and glacier dynamics, as well as in the construction of Digital Elevation Models(DEMs) of the Earth's surface and the classification of different land types have demonstrated its strength. As InSAR is a remote sensing technique, it has various sources of errors due to the satellite positions and attitude, atmosphere, and others. Therefore, it is important to validate its accuracy, especially for the DEM derived from Satellite SAR images. In this study, Real Time Kinematic(RTK) GPS and Kinematic GPS positioning were chosen as tools for the validation of InSAR derived DEM. The results showed that Kinematic GPS positioning had greater coverage of test area in terms of the number of measurements than RTK GPS. But tracking the satellites near and/or under trees md transmitting data between reference and rover receivers are still pending tasks in GPS techniques.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.2D
• /
• pp.159-166
• /
• 2012

During concrete placement, the formwork structure supports the weight of concrete mass. The complexity of the operation can cause concentrated workloads, which in turn brings about a collapse of the temporary structure. As a countermeasure, the operation needs to be constantly monitored to maintain safety and prevent accidents. This paper presents a USN (Ubiquitous Sensor Network)-based safety monitoring system for formwork construction. The system takes advantage of ubiquitous technology in monitoring the behavior of the formwork structure such as deflection, load weight, and tilting. The collected data are sent to the host computer wirelessly for real time monitoring. The data can be then compared with the allowed limits on guidelines. The comparison can indicate whether the concrete placement operation is executed in a safe condition.

• International Journal of Highway Engineering
• /
• v.5 no.2 s.16
• /
• pp.25-35
• /
• 2003

During construction of circular lifeline pipe, the non-proper compaction along the pipe and the decrease of compaction efficiency are the main problems to induce the failure of underground pipe. The use of CLSM(controlled low strength materials) is one of the applications to overcome those problems. In this research, the numerical analysis by PENTAGON FEM program was carried out for 20 cases with the couple of combinations on bedding materials, backfill materials, and pipes. From the FEM analysis, the use of CLSM as backfill materials reduced the settlement of ground surface and the deformation of pipe employed. In case of the vertical deformation on the pipe, common soil backfill for flexible pipes showed 2 times for rigid pipes, but CLSM backfill case did less deformation than the soil backfill for rigid pipes. CLSM backfills for rigid pipes showed the similar results. Judging from the FEM analysis, the use of CLSM increases the structure capacity of the underground pipes.

• Tunnel and Underground Space
• /
• v.22 no.6
• /
• pp.449-461
• /
• 2012

Coal ash generated from thermal power plants is planned to use for mine filling in order to prevent subsidence of the ground. In according, the basic physical properties and flow characteristics were grasped using coal ash from generated Yeongdong thermal power plant, and hydraulic filling experiments were performed a total of eight times by manufacturing the model of 1 inclined shaft in Hanbo coal mine. The specific gravity of coal ash is 2.34, and the result of particle size analysis belongs to silty sand (SM). Coal ash of weight ratio of 60% was used in the filling experiments of the model, since liquefaction have shown in coal ash less than weight ratio of 70% from the result of slump and flow test. The outlet should be located at the bottom of the inclined and vertical shaft, this was favorable way in improving the filling efficiency from the experiment results regardless of groundwater exists.

• International Journal of Highway Engineering
• /
• v.14 no.2
• /
• pp.45-53
• /
• 2012

Hollows are easily made and bearing capacity is lowered near underground structures of concrete pavement because of poor compaction and long term settlement of the ground. Distresses occur and lifespan is shortened because of larger stress induced by external loadings expected than that in the design. In this paper, the distresses of the concrete pavement slab over box culverts were investigated at the Korea Expressway Corporation(KEC) test road. The transverse cracking of the slabs over the culverts was compared between up and down lines with different soil cover depth. The box culvert without soil cover and concrete pavement were modeled and analyzed by the finite element method(FEM) to verify the transverse cracking at the test road. Wheel loading was applied after self weight of the pavement and temperature gradient of the concrete slab at Yeojoo, Gyeonggi where the test road is located were considered. Positions of maximum tensile stress and corresponding positions of the wheel loading were found for each loading combination. Joint position minimizing the maximum tensile stress was found and optimal slab length over the culverts with diverse size were suggested.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.11a
• /
• pp.213-234
• /
• 2002

우리 나라는 70년대까지 광업은 부흥하였으나, 그 이후 급속히 위축되면서 80년대 이후 거의 대부분 광산들이 폐광 또는 휴광된 실정이다. 그 결과 현재 전국 각지에 다수의 폐갱도가 존재하게 되었으며, 이제는 지반침하 및 각종 침출수의 원인자로 간주될 정도이다. 최근 지자체에서는 이런 폐갱도를 지역 자원으로서 가치를 인정하고 지역 활성화를 위해 재 이용하려는 움직임이 보이고 있는데, 구체적으로는 관광시설, 연구시설, 농업생산시설, 저장시설, 폐기물처리시설 등이다. 일본은 폐광된 금속광산 재활용을 위해 입지여건과 주변지역, 입갱 가능성 등 기초조사를 하였다. 조사결과 폐갱도의 문제점으로 입갱이 가능한 광산이 적다는 점을 들 수 있다. 대부분의 광산은 갱구가 함몰되었거나, 갱내에 지하수가 차 있어 접근이 불가능한 경우가 대부분이다. 비교적 양호한 암반 경우는 서브 레벨 스토핑, 잔주, 주방식 등의 채굴법에 의해 대규모 공동이 잔존하고 있는 경우도 있지만 그리 많지 않았다. 폐광된 광산 재활용 여건은 우리 나라와 일본이 대동소이 경우로 현실적으로 활용이 가능한 폐광은 많지 않으며 활용코자 할 때에는 기존갱도를 활용하면서 암반이 견고한 곳에 새로운 갱도를 설치하여야 한다. 그러나 몇몇 곳에서는 매우 유용하게 잘 활용되고 있는 곳도 있고, 연구 검토하면 충분한 활용성이 있다고 생각되는 곳도 있다. 그러므로 현재의 상황을 보고 판단할 것이 아니라, 활용기술과 접목해서 활용성을 검토함으로써 불용 자산의 유용화 방안이 검토되어야 할 것이다. 현재 가행중인 광산은 입지여건 및 암반이 양호하고, 대형갱도를 굴착하는 석회석광산 등을 선택하여 폐광 후 활용이 가능토록 채광기술 발전시켜 나가야 하며, 인간 중심적인 시설 또는 산물 중심적인 시설로 구분하여 폐광 후 복구비용을 우선 지원하는 방식 등을 통하여 시추, 탐광굴진, 현대화, 수갱굴착, 자금융자 등을 지원하는 우리 공사와 산업자원부가 지자체, 산림청, 건교부, 농림부 등과 연계하여 종합적인 지원육성책을 마련하여야 할 것이다. 결과적으로, 지방자치단체 등에서 관심을 갖고 있는 저장시설, 폐기물처리시설, 관광시설, 농업생산시설, 연구시설 등을 중심으로 ＆apos;광산 채굴적을 미래에 어떻게 활용한 것인가＆apos;를 선진외국 사례를 벤치마킹하고, 연구ㆍ검토하여 친환경적인 광산개발이 되도록 기본적인 방향과 개념을 갖도록 하여 관련 정책을 계획적이고, 체계적으로 수립 일관성 있게 추진해 나가야 할 것이다.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.11a
• /
• pp.3-21
• /
• 2002

국내의 휴ㆍ폐탄광 수는 2002년 현재 230여 개에 이르고 있다. 이에 따라 갱도, 폐석적치장 및 광산 시설물들은 방치상태로 남게 되며 광해의 주요인자가 되고 있다. 광해현상은 이들로부터 유출되는 산성광산배수(Acid Mine Drainage : AMD), 폐석 및 오염토양의 유실 및 하류부 퇴적, 채굴적 상부 및 인접지역의 지반침하 등이다. AMD는 pH가 6.0 미만이고 총산도(total acidity)가 총알카리도(total alkalinity)를 초과하는 물로서 노천광이 가행되었던 지역, 가행중이거나 휴광 또는 폐광된 광산에서 유출된다. 또한 도로사면 절개부나 지하철 터널에서도 황철석(pyrite)이나 백철석(marcasite)등을 함유하는 층이 공기 중에 노출되면 산성수가 침출되어 나오기도 한다. AMD에 의한 하천수의 오염이 매우 극심하여 때로는 미생물마저도 그 속에 살 수 없게 된다. AMD에 의해 오염된 하천수의 오염범위는 산성수의 양, 농도, 하천에 유입되는 산성수의 분포, 상류에서 흘러드는 오염되지 않은 물의 양, 지류에서 유입되는 물의 양에 따라 좌우된다. AMD 오염이 문제시되고 있는 나라는 미국을 포함하여 호주, 일본, 한국, 러시아, 남아연방 등이다. AMD를 처리하기 위해 여러 기술이 도입 적용되었으며 일부 기술들은 현재도 사용되고 있다. 각 기술마다 일장일단이 있으므로 경비의 과다, 유지 및 관리에 대한 지속성 여부, 공간의 확보 여부, 지역적 특수성에 맞춰 가장 적합한 방법을 채택하여야 하며 꾸준히 채택한 기술의 개량 및 새로운 기술의 첨가가 요구되고 있다. 따라서, AMD 오염지대에 대해 획일적으로 같은 처리방법을 채택하여 사용하는 것보다 각 지역 또는 AMD가 유출되어 나오는 광산폐기물의 특성 등을 고려하여 거기에 맞는 기술들을 복합적으로 또는 단독으로 사용하되 처리방법 채택 시 신중을 기할 것이 요망된다. 우리나라에서도 폐탄광을 복원하기 위하여 여러 시도가 있었으나 시간적, 경제적으로 충분히 고려하지 않아 시행착오을 범하고 있다. 따라서, 복원 대상광산에 대한 실제적인 조사, 평가 및 복구설계의 과정을 예로 들어 적절한 처리과정을 토의하고자 한다.