• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.10
• /
• pp.40-47
• /
• 2006

Optical performance of the mirror for satellite camera is highly dependent on the adhesive properties of its support. Therefore, in this paper, the adhesive properties of three kinds of space adhesives are investigated. For this purpose, the lap shear test is performed with Zerodur-to-metal lap shear specimen as well as metal-to-metal one. And it is also investigated whether reliable adhesive strength can be secured after the specific thermal cycle. Finally, the properties of three adhesives are compared with each other.

• Tunnel and Underground Space
• /
• v.30 no.6
• /
• pp.551-558
• /
• 2020

This note presents the calculation of nominal area for rock core specimen under direct shear testing condition. The initial nominal area was assumed as ellipsoid, and the equations for calculating the nominal area are derived. The normalized shear displacement and normalized nominal area have an identical relationship regardless of the ellipsoid shape. New testing constants and the generalized method were suggested to calculate the decrease of the nominal area. The method was applied to calculate the direct shear testing data and the changes of result were discussed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.129-132
• /
• 2008

Coupled shear wall system is the primary seismic load resisting system of buildings. The coupling beam of these buildings must exhibit excellent ductility and energy dissipation capacity. To achieve better ductility and energy dissipation, the steel coupling beam embedded in the reinforced concrete walls is proposed. Performance of the steel coupling beam is mainly effected by embedment length. ACI equation and BS equation were examined with 23 previous test results. The statistical study uses the values of mean value, standard deviation, correlation coefficient, normal distribution curve, and error analysis. Through the analytical program, the evaluation of the 2 equations was established.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.12 no.1
• /
• pp.67-77
• /
• 2008

Seismic isolation has been studied continuously as a solution of the seismic engineering to reduce the sectional forces and the damages of structures caused by earthquakes. To certify reliable design and installation of the seismic isolation systems, seismic isolation bearings should be fabricated under well planned quality control process, and proper evaluation tests for their seismic performance should be followed. In this study, shear property evaluation tests for the lead rubber bearings(LRB) and the rubber bearings(RB) were implemented and the temperature dependency tests were also implemented to evaluate the changes of shear properties according to the changes of temperature. After evaluation tests, the measured shear properties were compared to their design values and their deviation was analyzed comparing with the allowable error ranges specified in Highway Bridge Design Specifications. These results showed that a considerable number of isolation bearings have so large deviations from their design values that their error ranges were over or very close to the allowable ranges. And the test results for temperature dependency showed that the shear properties of isolation bearings would be changed in great degree by the change of temperature during their service period. If these two types of changes in their shear properties are superposed, it would possible that the changes of shear properties from their original design values are over than 50%.

• Journal of the Korea Concrete Institute
• /
• v.15 no.4
• /
• pp.513-521
• /
• 2003

Existing tests results have shown that confining the concrete compression region with closed stirrups improves the ductility and load-carrying capacity of beams. However, only few researchers have attempted to utilize the beneficial effects of the presence of these stirrups in design. This paper presents the result of experimental studies on the load-deflection behavior and the strengthening effect of laterally confined structural high-strength concrete beam members in which confinement stirrups have been introduced into the compression regions. Fifteen tests were conducted on full-scale beam specimens having concrete compressive strength of 41 MPa and 61 MPa. Different spacing of stirrups(0.25∼1.0d) and amount of tension steel($0.55{\sim}0.7{\rho}_b$) as major variables were investigated. And also, this study present an appropriate shear equation for decision of ultimate failure modes of high-strength concrete beams according to stirrup spacing. The equation is based on interaction between shear strength and displacement ductility. Prediction of failure mode from presented method and comparison with test results are also presenteded

• Composites Research
• /
• v.30 no.3
• /
• pp.215-222
• /
• 2017

The effect of a multi walled carbon nanotubes (MWNCT) on the adhesive properties and thermal properties of epoxy were studied by double lap-shear tests. Epoxy/MWCNT resins were prepared from a different amount of the MWCNT incorporated into the epoxy resins (araldite 2011). Steel plates and carbon fiber reinforced plastics (CFRP) were chosen as materials. Mechanical tests were performed by a universal testing machine (UTM). The analysis of thermal properties were conducted by a thermogravimetric analyzer (TGA) and a differential scanning calorimetry (DSC). The fracture surface morphology was examined using a scanning electron microscopy (SEM) and optical microscope. Compared to neat epoxy, it was found that the mechanical properties of epoxy/MWCNT resins are increased.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.62-68
• /
• 1997

In the first part of the paper, the crack growth process in rolling contact fatigue has been investigated on ring type plate specimens, in which crack growth is two dimensional and cracks are observed on the side surface of the specimens. The results have shown that cracks are initated from the contact surface in tensile mode in the direction approximately normal to the contact surface and after some short length of growth, shear mode growth occurs from the tip of the crack and it grows until the separation of the surface layer, namely flakung type failure, occurs. In the second part, mode U fatigue crack growth tests have been made by using an apparatus designed based on the concept that the subsurface fatigue crack growth in rolling contact fatigue is the mode U fatigue crack growth under the stress state where the tensile mode growth is suppressed by compression stress. The rest results have shown that the mode U fatigue crack growth occurs if the superposed compression stress is enough to suppress the tensile mode growth.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.2
• /
• pp.129-139
• /
• 2006

When blasting by imposing the time difference between two adjacent charge holes, the mutual interference phenomenon occurs depending the feature of blast. This interference phenomenon of blast amplifies or compensates the blast-induced vibration depending on the overlapping mechanism. Thus, this experiment aims at finding out the optimum delay time by measuring the blast vibration data from the single hole blast during the blasting test and composing each blasting waveform, and at proving the its efficiency by applying the composition delay time in the entire cross section. The experiment showed that the blasting-induced vibration was reduced by endowing an optimum delay time of electronic detonator appropriate to the rock quality of construction site compared to the typical delay time (20, 25ms) of existing detonator (non-electric and electric detonator). From these results, the excavation efficiency using blasting could be enhanced..

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.89-94
• /
• 2021

The mechanical reliability of flexible devices has become a major concern on their commercialization, where the importance of reliable bonding is highlighted. In terms of component materials' properties, it is important to consider thermal damage of polymer substrates that occupy large area of the flexible device. Therefore, room temperature bonding process is highly advantageous for implementing flexible device assemblies with mechanical reliability. Conventional epoxy resins for the bonding still require curing at high temperatures. Even after the curing procedure, the bonding joint loses flexibility and exhibits poor fatigue durability. To solve this problems, low-temperature and adhesive-free bonding are required. In this work, we develop a room temperature bonding process for polymer substrates using carbon nanotube heated by microwave irradiations. After depositing multiple-wall carbon nanotubes (MWNTs) on PET polymer substrates, they are heated locally with by microwave while the entire bonding specimen maintains room temperature and the heating induces mechanical entanglement of CNT-PET. The room temperature bonding was conducted for a PET/CNT/PET specimen at 600 watt of microwave power for 10 seconds. Thickness of the CNT bonding joint was very thin that it obtains flexibility as well. In order to evaluate the mechanical reliability of the joint specimen, we performed lap shear test, three-point bending test, and dynamic bending test, and confirmed excellent joint strength, flexibility, and bending durability from each test.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.65-65
• /
• 2017

밭작물 중 양파와 마늘은 높은 노동투하시간, 노임의 상승, 복잡한 수거 과정 등으로 최근 재배면적이 감소하는 추세이다. 밭농업 활성화 방안으로 생산비 절감과 작업 속도 향상을 위한 수확기계 개발 연구로 줄기절단기가 개발되었다. 이 연구는 줄기절단기 예취날의 설치각이 절단부하에 미치는 영향을 분립체 해석 기법으로 분석하고자 하였다. 실험에 사용한 시뮬레이션은 EDEM으로 인장탄성계수, 전단탄성 계수, 중첩길이, 입자 반경 및 질량, 상대속도를 이용하여 충돌시 힘을 해석하고 인장 및 전단강도, 한계, 결합 길이를 통해 입자간 결합을 설정할 수 있다. 시제품으로 설계된 줄기절단기의 치수를 활용하여 프로그램 상에서 줄기 절단 시뮬레이션을 진행하여 절단부하 결과를 얻도록 하였고 칼날 설치각을 30도, 45도, 60도로 변경하여 각각의 부하를 분석하여 경향성을 파악하고자 하였다. 실험에서 사용한 프로그램은 EDEM 2.7.1 Academic Research 버전이며 시뮬레이션을 진행한 PC의 사양은 Intel(R) $Core^{TM}$ i7-4790 CPU @ 3.60GHz, Memory 16.0GB이다. 줄기 절단 시뮬레이션에 적용시킨 줄기 모델은 마늘의 조건을 적용시켜 직경 1mm의 입자로 이루어진 지름 12mm, 높이 214mm의 원통형 모델이며 60.32N의 최대절단력을 가지고 있다. 줄기절단기는 2개의 회전날을 가지고 있으나 좌우대칭을 적용하여 절반에 대한 해석으로 하나의 회전날로 절단을 하도록 줄기 모델은 4조로 하여 3열을 140mm 간격으로 위치시켰다. 줄기절단기의 칼날은 반경 350mm로 회전하며 진행속도는 1.65m/s, 회전속도는 1680rpm으로 작업하도록 하였다. 시뮬레이션은 0.5초의 시간에 대해 해석하도록 하였으며 0.003초 간격으로 칼날에 가해지는 힘을 구하여 저장하도록 하였다. 시뮬레이션 해석시간은 약 116시간이었으며 설치각별 시간에 따른 칼날에 가해지는 압축력 값과 그래프를 얻을 수 있었다. 대부분의 시간에서 절단이 이루어지지 않으므로 0의 값을 나타내었으며 절단이 이루어지는 시점에 절단부하가 나타났다. 결과 해석을 위해 그래프의 피크 값들을 이용하였으며 그 중 상위 6개의 값으로 분석하였다. 30도, 45도, 60도의 설치각에 따른 절단부하의 평균 값은 각각 105.4N, 160.5N, 215.9N으로 나타났다. 설치각에 따른 절단부하의 경향성은 유의수준은 3.93%로 각각의 차이가 유의미하게 나타났으며 상관계수는 0.489로 증가하는 경향이 보였다. 그러나 $R^2$는 0.2394로 낮은 값을 보여 데이터 처리 방법의 개선과 적절한 회귀 모델의 적용이 필요하다. 향후 포장시험을 진행하고 복합적으로 분석하여 경향성을 자세히 분석하고자 한다.