• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.2
• /
• pp.92-98
• /
• 2019

In general, high strength and high performance fiber reinforced cement composites exclude coarse aggregates basically in order to have homogeneous distributions of material properties. However, these fiber-reinforced cement mortar without coarse aggregate have a tenancy that the modulus of elasticity is low and the unit weight of cement is high, resulting in low economic efficiency. Therefore, in this study, the development of high ductile fiber - reinforced concrete was conducted, which has the adequate level of coarse aggregate but still retains the high flexural toughness and strength and also has the crack - distributing performance. Experimental study was carried out by using the amount of coarse aggregate as an experimental parameter. The results showed that the best flexural toughness and crack dispersion characteristics was obtained when the coarse aggregate was added at 25% by weight of the fine aggregate to the typical mixtures of high ductile cement mortar. PVA fiber was effective in crack distribution and ductility enhancement, and steel fiber was effective in strengthening flexural strength rather than crack distribution.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.10
• /
• pp.5-15
• /
• 2008

The purpose of this study is to examine the validity of recycled aggregates (RAs) as a substitute for Sand-Mat material for soft ground improvement in the housing site development. To evaluate the possibility of RAs as a substitute for sand mat material, first of all, the criteria and regulations related with the quality of lateral drain layer were collected and checked. Secondly, both of the properties of RAs were compared with the properties of natural sand for the lateral drain layer. The material properties related to coefficient of permeability, pressure at-rest state and so on satisfied most standards. On the basis of the test results, RAs were used to the construction site as lateral drain layer. Accordingly, if the quality of RAs can be managed well, the application of these RAs as lateral drain layer to replace natural sand was highly effective. Also, based on cost analysis of two materials, RAs are proved to be very competitive.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.438-446
• /
• 2001

Recently, porous concrete has been used for the purpose of decreasing the load of earth environment. It consists solely of cement, water and uniform-sized coarse aggregate. And its fundamental properties will be considerably affected by the physical properties of aggregate because the aggregate occupies for the most part in its mix proportion. For such a reason, this study was carried out to investigate the influence of the sizes and kinds of aggregate for the fundamental properties of porous concrete. It showed that the fundamental properties of porous concrete were the similar value in all sizes of aggregate except in the case of using the 2.5∼5㎜ aggregate and were varied according to the kinds of aggregate. In particular, compressive strength of porous concrete using 2.5∼5㎜ aggregate was more higher than that using other aggregate, and its void ratio and coefficient of permeability was lower. And the maintenance capacity of permeability of porous concrete was varied by the sizes and the kinds of aggregate. In particular, it was greatly decreased in case of using the 2.5∼5㎜ aggregate. And unlike dynamic modulus of elasticity of ordinary concrete, that of porous concrete was very high value in early ages and was slowly increased after that time.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.6
• /
• pp.301-306
• /
• 2010

The artificial aggregates were fabricated by using the inorganic wastes, dredged soil produced at a dredging work. The input temperature ($800{\sim}1000^{\circ}C$), output temperature ($1100{\sim}1200^{\circ}C$) and heating rate ($5{\sim}10^{\circ}C$/min) in sintering process were controlled to fabricate the aggregates with various value of density and water absorption, and their properties were analyzed as a function of those factors. The specimens sintered at the lower input temperature showed the higher density and the lower water absorption while those with higher input temperature had many pores inside of the aggregates, lower density and higher water absorption. Also increasing the input temperature accelerated the black core phenomenon in the aggregates. The bloating phenomena which the gigantic pores were generated inside the aggregates were improved as increasing the output temperature, but its effect was lower than that of input temperature. It could be realized that the bloating tendency was improved from the results that the density was increased and water absorption was decreased with increasing heating rate from 5 to $10^{\circ}C$/min. It was found that the artificial aggregates of light or heavy weight with various value of density and water absorption could be fabricated by using dredged soils naturally involving gas and fluxing components by controlling the sintering conditions.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.2
• /
• pp.133-140
• /
• 2018

The objective of this study is to propose a reliable mixing design procedure of concrete using artificial lightweight aggregate produced from expanded bottom ash and dredged soil. Based on test results obtained from 25 mixes, empirical equations to determine water-to-cement ratio, unit cement content, and replacement level of lightweight fine aggregates were formulated with regard to the targeted performance (compressive strength, dry density, initial slump, and air content) of lightweight aggregate concrete. From the proposed equations and absolute volume mixing concept, unit weight of each ingredient was calculated. The proposed mix design procedure limits the fine aggregate-to-total aggregate ratio by considering the replacement level of lightweight fine aggregates, different to previous approach for expanded fly ash and clay-based lightweight aggregate concrete. Thus, it is expected that the proposed procedure is effectively applied for determining the first trial mixing proportions for the designed requirements of concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.765-768
• /
• 2008

The prevent methods of Alkali-Silica Reaction (ASR) are studying after the failure cases by ASR were reported in Korea. When ASR failure is causing to the step of maintenance, the available repair methods were rarely studied in the World. In this study, premixed fly ash cement was applied to prevent ASR in the concrete pavement. The ratio of fly ash and cement is 20 percent and 80 percent by weight of total cementious material. The construction performance of premixed fly ash cementious concrete pavement was studied that the application is verify to performance collected data during the constructing in the field. The freeze-thaw test was studied to verify durability of the premixed fly ash cementious material made specimen in the laboratory. The results show that construction performance and durability are well condition in this test section and freeze-thaw test.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.6
• /
• pp.74-87
• /
• 2020

Overloaded trucks are the main source that threatens road safety and directly affects the reduction of pavement life. The On-board truck scale is the only equipment that could prevent overloading by measuring and adjusting the loading weight before driving. Legislation is needed to encourage its installation so that the driver can prevent overloading. In this study, an on-board truck scale system was installed on 30 dump trucks for transporting construction waste, such as soil and aggregates, which are major loads of 36.55% for overloading, and the trucks were monitored remotely. The overload prevention effect was analyzed by comparing driving data for 1 month before distribution of the weight display app that can recognize the weight to the driver and 1 month after distribution. After installation, overloading could be 6.1% reduced, and the transportation efficiency could be increased by checking the weight provided from the On-board truck scale system.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.4
• /
• pp.270-278
• /
• 2005

Recycled aggregate concrete has lower strength and durability compared to concrete with natural aggregate. Therefore, metakaolin is used to improve the properties of recycled aggregate concrete. Main components of metakaolin are $SiO_2$ and $Al_2O_3$. and specific surface area is 9 times larger than that of ordinary portland cement. Quality of demolished-recycled aggregate(DRA) satisfies the type 1 of KS F 2573, but quality of source-recycled aggregate(SRA) does not satisfy with the type 2 of KS F 2573. When metakaolin was replaced with 20% of cement, compressive strength of concrete with SRA and DRA develops about 40~64% of control concrete. Water absorption ratio was reduced about 2% by replacing 20% metakaolin and it represents low compared to the natural aggregate concrete without metakaolin. In addition, the resistance to freezing and thawing, of concrete with DRA is indicated to remarkably enhanced due to the contribution of metakaolin. However, when metakaolin is replaced with 20% of cement, relative dynamic modulus of elasticity of concrete with SRA was below 60% at 210 freezing and thawing cycles.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.75-81
• /
• 2012

In case of crushing rock to produce materials for lean concrete subbase layer in concrete pavement, natural sand is used for the gradation adjustment of aggregates, and the percentage of natural sand used is 30%~40% of the weight ratio of aggregate mix. The supply of natural sand that is used in lean concrete as a fine aggregate is getting harder due to the current of exhaustion of source, and the cost for the purchase of natural sand is included in the cost of roadway construction. This study, therefore, was conducted in order to resolve the exhaustion of materials and economize in construction expenditure by the application of screenings, which is by-product of crushing rock in quarry, as an alternative to natural sand. As a result of a comparative analysis on the application of screenings and natural sand with typical types of rock that is produced in domestic, which was conducted in the first year, It is found out that the use of screenings as a fine aggregate showed better unconfined compression strength. Verification of actual application of screenings was conducted in the second year, after test construction and follow-up investigation. The compressive strength, compaction density, settlement of screenings applied case was higher than that of natural sand. Thus, it is expected that application of screenings to construction in field will contribute to the cost saving, material recycling and the protection of environment.

• Land and Housing Review
• /
• v.2 no.1
• /
• pp.69-78
• /
• 2011

The purpose of this research is particle shape evaluation of aggregate using Digital Image Process(DIP). DIP is very useful to measure the roughness and particle shape of aggregates. Couple of aggregates, like standard sand, two different crushed stones, and two different marine aggregates, have been employed. Shape factors of two different marine aggregates are ranged 0.35 to 0.54. Crushed stone I is 0.74 which is highly flat, but standard sand is elongated shape. Especially, two marine aggregate showed a big difference of width and length which meaned a long shape. There is any significant difference of elongation ratio and flatness for each aggregate with different measuring system, like direct measurement of vernier calipers and DIP method. Shape conversion coefficient and equivalent diameter for changing 2D image to 3D image by the Digital Image Process(DIP) have been suggested and modified particle size distribution curve has been showed. The measured flatness ratios of each aggregate were 0.30, 0.36, 0.47 and 0.83, respectively. Also, the conversion shape coefficients of each aggregate were determinded as 0.77, 0.78, 0.84 and 0.92. The size of aggregate has been modified by multiplying the shape conversion coefficient and the aggregate size from DIP. The modified gradation curve with modified volume and weight of aggregate has been suggested. Within the limited test results, DIP is one of useful to get the particle shape of aggregate with limitation of measuring errors and to apply the particle distribution curve.