• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.45-52
• /
• 2016

One commercial package for magnetic analysis was used to apply repulsive forces of permanent magnetics to bicycle cushion system. Reliabilities of finite element analysis were acquired by comparing with those of experimental measurements. Equivalent spring stiffnesses corresponding to various sizes of magnetics were implemented into the bicycle dynamic model with three degree of freedom. Input force caused at front and rear wheels due to road unevenness was considered in the dynamic model. Dynamic behaviors were observed in terms of vertical displacements of the rider and the front reach as well as pitching displacement of the mass center when the bicycle ran over half-triangular bump. The methodology suggested in this paper by the finite element analysis and numerical model will be an useful tool for more accurate prediction of cushion design for any vehicle system if magnetic forces are utilized.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.86-92
• /
• 2017

In this study, a running performance evaluation and roller rig test was conducted to evaluate the applicability of a composite bogie frame, which has the role of the primary suspension. The composite bogie frame was made of a GEP224 glass/epoxy prepreg. Vehicle dynamic analysis was carried out on the composite bogie with three different kinds of side beam thicknesses (50 mm, 80 mm, and 150 mm). From the results, the composite bogie with a side beam thickness of 80 mm satisfied all the dynamic design requirements. Although the composite bogie with the side beam thickness of 50mm also met the design requirements, its critical speed was just a 2% margin to the requirement. In contrast, the model of the side beam thickness of 150mm did not meet the ride comfort. In addition, a composite bogie frame with the side beam thickness of 80 mm was fabricated and installed on a complete bogie. Moreover, the roller rig test using the fully equipped bogie was performed to evaluate the critical speed. During the test, the lateral excitation was imposed on the wheelsets to realize the rail irregularity. There was no divergence of the lateral displacement of the wheelsets while increasing the speed. The measured critical speed was similar to the predicted result.

• Review of KIISC
• /
• v.33 no.4
• /
• pp.23-29
• /
• 2023

대부분의 임베디드 시스템은 기계장치와 전자기기 장치가 함께 작동되는 물리 장치로써, 이기종 네트워크, 복잡한 보안체계 등을 고려하여 가상화 기반 사이버훈련 환경이 구성되어야 한다. 또한, 차량을 대상으로 물리적인 실험환경에서 모의침투 등 사이버훈련을 수행한다는 것은 교통사고를 비롯한 안전사고 발생에 있어 위험이 존재한다. 본 논문에서는 가상 개발환경에서의 공격 기반 차량용 사이버훈련 프레임워크를 제안하고자 한다. 먼저, 공격 기반 차량용 사이버훈련 프레임워크의 작동은 자동 활성화되는 가상의 CAN 네트워크 인터페이스로 시작된다. 가상의 CAN 네트워크 인터페이스는 가상 머신에서 간단한 부트스트랩 명령어 실행을 통해 파이썬 패키지와 Ubuntu 서비스 목록 설치 명령이 자동으로 실행되면서 설치된다. 이후 내부 네트워크 시뮬레이터와 공격모듈과 관련된 UI가 자동으로 Ubuntu Systemd에 의해 백그라운드에서 실행되어 시작과 동시에 준비 상태를 유지하게 된다. 사이버훈련 UI 내 공격 모듈은 사용자에 의한 공격 선택 및 파라미터 셋팅 이후 차량의 이상 상태를 사이버훈련 UI에 다시 출력되게 된다. 본 논문에서 제안하는 가상 개발환경 기반의 차량용 사이버훈련 프레임워크는 자율주행 차량 사고의 위험이나 다른 특수한 제약 없이 사용자의 학습 경험을 확장시킬 수 있다. 또한, 기존의 가상화 기반 사이버훈련 교육 콘텐츠와는 달리 일반 사용자들이 접근하기 쉬운 형태로 확장 개발이 가능하다.

• Journal of the Korean Society for Railway
• /
• v.2 no.2
• /
• pp.31-38
• /
• 1999

Two representative types of the AGT (Automated Guideway Transit) system, which are bogie and steering types, are available for the side-guided system. Each system primarily consists of the bogie frame, suspensions, wheelsets and axles, braking system and transmission system. Among these components, the bogie frame is one of the most significant components subjected to the whole vehicle and passenger loads. This paper describes structural analyses and associated fatigue analyses for each bogie frame depending on the various loading conditions on a basis of the railway vehicle code UIC 515-4. Subsequently, comparisons are made between those two types to estimate which type is more reliable in terms of strength and fatigue. It is observed that the bogie type is a little advantageous over the steering one from the strength analysis. However, the two types are found to be in a reliable range of fatigue even though a realistic fatigue load case is further carried out. In addition, an optimal size of thickness is suggested for designs of the bogie frame.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.6
• /
• pp.49-56
• /
• 2011

Leisure bicycles are fabricated in a variety of ways these days. Although, the bicycles are designed and manufactured in a variety of ways by numerous companies, customer has a difficulty in gaining information of bicycle which suits them. Accordingly most of buyers purchase bicycle considering body size. Employing the method is one of the ways to decide bike size on the ground of standard body measurement. However, the method above to purchase bicycle is not appropriate for customer considering his/her body. The research mainly aims to design bicycle which allows buyer to adjust optimal design system by himself/herself considering his/her body size. In addition, a device employing fuzzy controller implemented bicycle run test. Using on the result, the research explored an optimal bicycle system which makes a decision whether a bicycle fits body of customer.

• Journal of the Korean Society for Railway
• /
• v.20 no.4
• /
• pp.440-447
• /
• 2017

Spectrum level for the acoustic roughness of wheels and rail surface should be periodically maintained under the limitation of ISO to reduce rolling noise of railway vehicles. Thus, in maintaining railway track, displacement sensor-based measuring devices are broadly used to measure the surface roughness and to perform spectral analysis. However, these measuring devices cause unexpected measuring errors since the displacement sensors are fixed at moving platforms and the main frame produces pitching motion during measurement. To increase the accuracy of the measured values, this paper has investigated the effects of design variables such as wheel base, additional wheels, and elastic deformation of wheels on the surface roughness and acoustic roughness spectrum.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5854-5860
• /
• 2014

The on-site performance of a vision-based displacement measurement system (VDMS) was evaluated through a field test on a bridge. The VDMS used in this study is composed of a camera, a marker, a frame grabber, and a laptop. The system measures the displacement by attaching a marker at the location to be measured on the structure, by capturing images of that marker with a fixed rate, and by processing a series of images using a planar homography technique. The developed system was first validated from a laboratory test using a small-scale building structure. The VDMS was then employed in a field test on a railroad bridge with a KTX train running under various conditions. The on-site performance was evaluated by comparing the obtained displacement using the VDMS with the displacement measured from a laser Doppler vibrometer (LDV), which is an expensive and accurate displacement measurement device.

• Journal of the Korean Society for Railway
• /
• v.3 no.3
• /
• pp.117-124
• /
• 2000

The rubber wheel-type AGT has two major kinds of bogie; one is the bogie type and the other steering one. Both are important vehicular structure to support the whole running vehicle and passenger loads. This paper deals with the static analysis for the two types of bogie frame subjected to combined external forces, as well as independent ones specified in UIC 515-4. Furthermore, the dynamic analysis is performed under vibrational loading conditions so as to compare dynamic characteristics, Numerical results by using commercial packages, I-DEAS and NASTRAN show that maximum stresses do not exceed the yield strength level of material used for both bogies. From an overall viewpoint of strength, the bogie type turns out to be superior to the steering type except for the case of a lateral loading. It is also observed that the steering type shows a characteristics of low frequency behavior during a course of searching for structurally weak areas to be stiffened. The vibrational fatigue analysis for each bogie frame depends on the loading time history conditions which is applied. Time History Central Database List in the NASTRAN package. Subsequent1y, the fatigue life of bogie type is longer than the steering type.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.80-80
• /
• 2017

국내에서 대부분 생산되는 사료(사일리지) 수확 작업은 베일 생산 및 비닐 래핑 작업이 독립적으로 수행되고 있어서 비효율적이다. 본 연구에서 개발한 조사료 수확기는 수집, 롤링, 베일 네트 생성, 래핑, 래핑 종료 및 베일 방출작업을 통합적으로 수행하도록 설계-제작하였다. 통합형 다목적 조사료수확기의 설계는 3D 디자인 툴 (CATIA V5R18)을 이용하여 실시하였으며, 기구부 23 파트 어셈블리, 전기제어 어셈블리, 유압요소기술을 통합하여 통합시작기를 제작하였다. 기초 프레임, 오거장치파트, 픽업장치파트, 하부롤러파트, 상부롤러파트, 하부 프레임 및 주행부 파트, 래핑회전파트, 롤러부 구동 동력부, 유압파트, 전기제어파트, 드로우바파트, 체결 및 컨트롤러 파트 등 25개 파트로 구성되어 있다. 본 연구에서 개발한 시작기의 견인력 및 소요동력 분석은 선행 연구에서 사용한 Brixius (1987) 제안 모델을 체택하여 분석하였다. 이 Brixius 제안 모델은 견인력 예측에서 토양변수 및 토양강도 특성을 나타내는 원추지수 (Cone Index, CI)를 이용하여 트랙터의 견인력 예측에 사용하였다. 또한 트랙터-조사료수확기 시스템의 소요 견인력을 예측하는데 있어, 트랙터-조사료수확기 시스템이 운용되는 토양조건과 트랙터의 마력에 따른 소요 견인력 특성을 분석하기 위해 대표적으로 3수준의 토양조건 (CI: 356 kPa, 543 kPa, 1,429 kPa)을 적용하였으며, 베일의 개당 최대무게는 최고 수준인 옥수수 기준으로 800 kgf를 적용하였다. 본 연구에서 적용된 3수준의 CI 조건은 연구팀에서 선행연구과정 (토양특성에 따른 최적 경운작업 시스템 개발, 2006)에서 분석한 전국 10개 지역의 33개 지점의 경반층 CI지수의 측정범위인 1,050-3,170 kPa에 대해 견인력이 많이 소요되는 열악한 조건 수준을 적용하였다. 각 작업에 사용된 소요동력은 베일 작업시 (ASABE D497.7, 2011) 그리고 래핑작업시 (Zhortuylov et al., 2013)를 사용하였으며 두 소요마력을 트랙터-조사료 수확기 시스템의 필요 소요마력의 합계로 계산하였다. 트랙터-조사료수확기 시스템의 최소 소요 동력, 차축 소요 동력과 PTO 소요 동력을 Zoz and Grisso (2003)을 이용하여 계산하였다. 연구에서는 기본적으로 ASAE의 작업속도 및 작업효율을 적용하였는데, 적용된 조사료수확기의 현장 작업효율은 60-86%의 범위이고 일반적으로 70%를 적용하고 이때 작업속도는 2.5-8.0 km/h이며 전형적으로 5.0 km/h를 기준하고 있다. 자주식 (SP; sief-propelled machine) 조사료수확기의 경우 작업속도가 2.5-10.0 km/h의 범위에서 작업효율은 60-85% 범위이다. 적용되는 조사료 수확기의 작업효율인 60-85% 범위에서 일반적으로 적용되는 작업효율인 70%를 적용하면 트랙터의 소요동력은 95hp를 적정 작업환경으로 하였다.

• The KIPS Transactions:PartB
• /
• v.14B no.3 s.113
• /
• pp.163-170
• /
• 2007

In autonomous navigation of a mobile vehicle or a mobile robot, localization calculated from recognizing its environment is most important factor. Generally, we can determine position and pose of a camera equipped mobile vehicle or mobile robot using INS and GPS but, in this case, we must use enough known ground landmark for accurate localization. hi contrast with homography method to calculate position and pose of a camera by only using the relation of two dimensional feature point between two frames, in this paper, we propose a method to calculate the position and the pose of a camera using relation between the location to predict through perspective transform of 3D feature points obtained by overlaying 3D model with previous frame using GPS and INS input and the location of corresponding feature point calculated using KLT tracking method in current frame. For the purpose of the performance evaluation, we use wireless-controlled vehicle mounted CCD camera, GPS and INS, and performed the test to calculate the location and the rotation angle of the camera with the video sequence stream obtained at 15Hz frame rate.